RG100A-AA刷机教程

序言序言序言序言 刷坏了不要找我，没有动手能力的不要找我。。。有什么在帖子问吧我 也不算高手，大家一起讨论，最近捡到一个 RG100A-AA的路由器（不 要喷我，的确没花一分钱朋友不喜欢送我的。。约等于捡到）于是上 网找刷机教程翻遍整个互联网只有零星的一些资料，看到很多人问也 没人说明白今天有空把我这几天的工作做个 总结 初级经济法重点总结下载党员个人总结TXt高中句型全总结.doc高中句型全总结.doc理论力学知识点总结pdf 希望也能帮到大家。 准备工作准备工作准备工作准备工作 1.电烙铁一把，助焊剂一些（推荐松香），焊锡一些（尽量选硒多铅 少的） 2.万用表一块（数字，模拟均可） 3. 25针公头一只,100欧姆电阻 4只 4.传输线若干（可以选一些好线能屏蔽线）我自己好找不知道其他朋 友们咋样 5.操作人一个（不要砸我啊）。。。 教程教程教程教程 首先我们来做 JTAG 线(愿意淘宝的自己淘宝。。。这东西我是不淘宝 了的。。。DYI么呵呵）上线路图（用别人的自己懒的画了相机也不好) 必备的东西很容易做还是做个好吧 12针 JTAG接口定义：（贝尔 RG100A-AA) 1、nTRST 2、GND 3、TDI 4、GND 5、TDO 6、GND 7、TMS 8、GND 9、TCK 10、GND 11、nTRST 12、GND JTAG线路图 JTAG连接线大家尽量短（按某大大的说法速度快稳定事实也是这样) JTAG软件软件软件软件 留个位置怕某些同志不会用这个软件（留以后上软件使用说明） TTL线制作 方法 快递客服问题件处理详细方法山木方法pdf计算方法pdf华与华方法下载八字理论方法下载 线制作方法线制作方法线制作方法 这个线的做法很多地方都有但是对于大多数朋友来说还是比较麻烦 （淘宝把。。） 我的做法是很早有一个 8210 数据线拆开以后芯片被打磨过不知道是 什么型号但是通过看外围元件和手机原理可以知道这种东西一般就 是MX232呵呵，在加个 USB转 SR232的口轻松搞定。上图图 RG100A-AA-TTL定义图（郁闷继续用别人的图） TTL线和 USB-SR232图图(继续郁闷等相继用= =！） [attach]26410[/attach] 2、 顺利连接上(O(∩_∩)O~） Boot Address 0xbe000000 Initializing Arena. Initializing Devices. Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000] AuxFS[93,0xbeba0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000] Flash RootFS Partition Length: 12058624 CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz CPU running TP0 Total memory: 33554432 bytes (32MB) Total memory used by CFE: 0x80401000 - 0x80529860 (1214560) Initialized Data: 0x8041E740 - 0x80421060 (10528) Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-8) : 96358VW2 Number of MAC Addresses (1-32) : 12 Base MAC Address : 00:1f:a3:49:XX:XX PSI Size (1-64) KBytes : 24 Flash Block Size (1-128) in KBytes: 128 Auxillary File System Size Percent: 25 Main Thread Number [0|1] : 0 udp_send finished No answer .auto boot ... *** Press any key to stop auto run (1 seconds) ***（在此快速点击回车） Auto run second count down: 0 Code Address: 0x80010000, Entry Address: 0x80010000 Decompression OK! Entry at 0x80010000 Closing network. Starting program at 0x80010000 Linux version 2.6.30.9 (yuzt@Ubuntu) (gcc version 4.3.3 (GCC) ) #3 Tue Nov 17 00:48:10 CST 2009 Detected Broadcom 0x6358 CPU revision a1 CPU frequency is 300000000 Hz 32MB of RAM installed registering 40 GPIOs board_bcm963xx: CFE version: 1.0.37-10.3 console [early0] enabled CPU revision is: 0002a010 (Broadcom BCM6358) board_bcm963xx: board name: 96358VW2 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00002000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00002000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes. Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 128 (order: 7, 512 bytes) Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 29504k/32768k available (2079k kernel code, 3264k reserved, 429k data, 132k init, 0k highmem) Calibrating delay loop... 299.00 BogoMIPS (lpj=598016) Mount-cache hash table entries: 512 net_namespace: 532 bytes NET: Registered protocol family 16 registering PCI controller with io_map_base unset bio: create slab at 0 PCI: Enabling device 0000:00:01.0 (0000 -> 0002) ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered NET: Registered protocol family 1 audit: initializing netlink socket (disabled) type=2000 audit(0.310:1): initialized squashfs: version 4.0 (2009/01/31) Phillip Lougher Registering mini_fo version $Id$ JFFS2 version 2.2. (NAND) (SUMMARY) 漏 2001-2006 Red Hat, Inc. msgmni has been set to 57 alg: No test for stdrng (krng) io scheduler noop registered io scheduler deadline registered (default) gpiodev: gpio device registered with major 254 gpiodev: gpio platform device registered with access mask FFFFFFFF bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart console handover: boot [early0] -> real [ttyS0] bcm63xx_enet MII bus: probed bcm963xx_flash: 0x02000000 at 0x1e000000 bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 bcm963xx: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. bcm963xx_flash: Read Signature value of CFE1CFE1 bcm963xx_flash: CFE bootloader detected bcm963xx_flash: CFE boot tag found with version 6, board type 96358VW2, and tagid bc310. bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000 bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00 bcm963xx_flash: Partition 2 is rootfs offset 100000 and length ee0000 bcm963xx_flash: Partition 3 is nvram offset fe0000 and length 20000 bcm963xx_flash: Partition 4 is linux offset 20000 and length fc0000 bcm963xx_flash: Spare partition is 460000 offset and length b80000 Creating 5 MTD partitions on "bcm963xx": 0x000000000000-0x000000020000 : "CFE" 0x000000020100-0x000000100000 : "kernel" mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only 0x000000100000-0x000000fe0000 : "rootfs" mtd: partition "rootfs" set to be root filesystem mtd: partition "rootfs_data" created automatically, ofs=460000, len=B80000 0x000000460000-0x000000fe0000 : "rootfs_data" 0x000000fe0000-0x000001000000 : "nvram" 0x000000020000-0x000000fe0000 : "linux" bcm63xx_wdt started, timer margin: 30 sec Registered led device: adsl Registered led device: ppp-fail Registered led device: power Registered led device: stop Registered led device: TCP westwood registered NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly on device 31:2. Freeing unused kernel memory: 132k freed Please be patient, while OpenWrt loads ... 3、- preinit - Press CTRL-C for failsafe switching to jffs2 mini_fo: using base directory: / mini_fo: using storage directory: /jffs - init - Please press Enter to activate this console. eth1: link forced UP - 100/full - flow control off/off device eth1.0 entered promiscuous mode device eth1 entered promiscuous mode br-lan: port 1(eth1.0) entering forwarding state cfg80211: Using static regulatory domain info cfg80211: Regulatory domain: US (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) cfg80211: Calling CRDA for country: US PPP generic driver version 2.4.2 NET: Registered protocol family 24 SCSI subsystem initialized roboswitch: Probing device eth0: <3>roboswitch: [/media/router/routerLinux/openwrt/build_dir/linux-brcm63xx/kmod-swit ch/switch-robo.c:131] SIOCGETCPHYRD failed! roboswitch: [/media/router/routerLinux/openwrt/build_dir/linux-brcm63xx/kmod-swit ch/switch-robo.c:131] SIOCGETCPHYRD failed! No Robo switch in managed mode found, phy_id = 0xffffffff roboswitch: Probing device eth1: found a 5325! It's a 5350. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb b43-phy0: Broadcom 4318 WLAN found (core revision 9) Registered led device: b43-phy0::tx Registered led device: b43-phy0::rx Registered led device: b43-phy0::radio Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ] NTFS driver 2.1.29 [Flags: R/O MODULE]. loop: module loaded tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky ip_tables: (C) 2000-2006 Netfilter Core Team Driver 'sd' needs updating - please use bus_type methods ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1 bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300 bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected nf_conntrack version 0.5.0 (512 buckets, 2048 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. IMQ driver loaded successfully. Hooking IMQ before NAT on PREROUTING. Hooking IMQ after NAT on POSTROUTING. xt_time: kernel timezone is -0000 nf_conntrack_rtsp v0.6.21 loading nf_nat_rtsp v0.6.21 loading arp_tables: (C) 2002 David S. Miller ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2 bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd: USB Universal Host Controller Interface driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. fuse init (API version 7.11) b43 ssb0:0: firmware: requesting b43/ucode5.fw b43 ssb0:0: firmware: requesting b43/pcm5.fw b43 ssb0:0: firmware: requesting b43/b0g0initvals5.fw b43 ssb0:0: firmware: requesting b43/b0g0bsinitvals5.fw b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10) device wlan0 entered promiscuous mode br-lan: port 2(wlan0) entering disabled state b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10) br-lan: port 2(wlan0) entering forwarding state BusyBox v1.14.4 (2009-11-14 01:59:39 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M KAMIKAZE (bleeding edge, r18405) ------------------ * 10 oz Vodka Shake well with ice and strain * 10 oz Triple sec mixture into 10 shot glasses. * 10 oz lime juice Salute! --------------------------------------------------- root@OpenWrt:/# 关于很多网友出现 RG100A-AA老重启的解决方法 说来你不信就是固件问题引起的这个时候请用 TTL 线连接后在上面 红字处按回车速度要快啊进入CFE以后请用 e a清楚掉芯片的所有内 容有的大大说 e n好些我认为 e a是最可靠的呵呵个人想法不做评论 4、 硬件部分大致和上面差不多等细化吧 软件部分软件部分软件部分软件部分 根据个人这几天的经验刷新固件比较好的 CFE 还是 RG100A-AA 自 带的好其他我也试过一些都有问题所以经验啊还是原机 CFE 吧，在 有看到很多朋友说 CFE的密码不对提供几个基本都是他们, 1:USER=telecomadmin pass=telecomadmin 2:user=telecomadmin pass=nE7jA%5m 3:user=bjcnchgw pass=8mCnC@bj