通风空调工程定额解释.

第九册通风空调工程定额解释1．通风管道工程量计算时“不包括部件所占长度”，其部件及其长度如何界定？答：通风管道部件是指风管阀门、风口、风帽、罩类、静压箱及消声器等部件，其长度应按设计图纸或其采用的标准图集标示的长度计算。2．帆布接口与柔性软风管有何区别？答：区别在于：（1）功能不同：前者是用于设备与风管或部件的连接；后者是用于不易于设置刚性风管位置的挠性风管，属通风管道系统。（2）固定方式不同：前者采用法兰连接形式，一般不设专门的支托吊架；后者采用镀锌皮卡子连接，采用吊托支架固定。（3）长度不同：前者按标准图集长度常为150—250mm；后者长度一般在0.5—2.5m左右。（4）材质不同：前者定额中采用帆布；后者是由金属，涂塑化纤织物，聚酯、聚乙烯、聚氯乙烯薄膜、铝箔等材料制成的。（5）定额内容不同：前者为现场制作安装；后者为成品软管安装。在套用定额时应注意：柔性软风管如每根长度小于3m时，可直接采用定额，如每根大于3m时，可按3m一根折算，不足3m按3m计。3．多叶排烟口及板式排烟口是按在什么位置安装考虑的？答：该定额是按安装在墙上或通风井道壁上进行编制的。如是安装在通风管道上的防火排烟风口，则按第二章相应防火阀定额执行。4．遇到折板式消声器安装应执行什么定额？答：折板式消声器是新产品，如遇有折板式消声器安装可执行同规格阻抗式复合消声器定额项目。5．轴流风机防雨短管制作安装项目如何执行定额？答：轴流风机防雨短管制作安装可按风管壁厚使用相应通风管道定额项目，人工乘以系数3.0。6．净化风管制作安装未包括膨胀螺栓及电锤台班的消耗量，请问其支架的固定方式是怎样考虑的？答：净化风管支架的固定是按在预埋铁件上焊接考虑的。如设计要求采用膨胀螺栓固定支架，可按实际调整相关消耗量。7．第十章说明第七条 规定 关于下班后关闭电源的规定党章中关于入党时间的规定公务员考核规定下载规定办法文件下载宁波关于闷顶的规定 ：铝板风管采用咬口、法兰连接形式，可参照第一章镀锌钢板咬口连接项目执行。请问，执行第一章相应项目时，可否调整不同的材料？答：可以按图纸设计或标准的要求进行调整。比如铝质铆钉、铝质型材或螺栓、垫圈等均可调整。8．铝板风管制安没考虑加固框，如发生时，应如何执行定额？答：铝板风管一般设计不需要加固框。如发生时，可按9-548、549项目执行，需扣除紧固、密封材料。9．成品风管法兰的重量是否包括焊条、焊丝的增重？答：从理论上说，成品风管法兰重量内，已包括成型后焊缝填充材料的重量，不应另行增加焊条、焊丝重量。10．风阀电动执行机构安装定额中是否包括其电气系统安装？答：风阀电（气）动执行机构的安装，只包括本体安装、就位、固定，不包括执行机构动力系统的安装调试，该部分应执行第二册定额相关规定。11．各类冷水机组设备安装包括哪些工作内容？答：各类冷水机组均属定型设备，定额中是按整体安装就位考虑的，包括设备本体及其配套的附件的安装，以及设备无负荷试车以及配合生产厂家负荷试车的内容。设备安装技术说明要求在现场进行拆装检查，应按第一册压缩机拆装检查相应项目执行。设备安装不包括设备充工质及系统调试内容。12．本册中的冷水机组、风机、除尘器等各类设备安装，可否同第一册一样，计取“起重机具摊销费”？答：本册的设备安装对此没有规定，该部分内容已含在定额内，所以不能计取。13．设置于竖井及已完吊顶内的空调通风管道系统安装，是否应增加人工调整系数？答：属于管道间、已封闭吊顶内的空调通风管道系统，在执行本册定额时，其人工应乘以系数1.3。调整系数序号所处位置系数名称计取规定适用范围备注9.1P4说明十二·2脚手架搭拆费定额人工费×3%（其中人工占25%）全册 9.2P4册说明十二·3通风空调工程系统调整费系统工程人工费×13%（其中人工占25%）全册 9.3P3册说明十一·1超高增加消耗量操作物高度计算 方法 快递客服问题件处理详细方法山木方法pdf计算方法pdf华与华方法下载八字理论方法下载 定额中操作物高度距楼地面超过6m时计取，不扣除6m以下工程量的定额人工 ≤10m定额人工费×1.10≤15m定额人工费×1.15≤20m定额人工费×1.20＞20m定额人工费×1.409.4P4册说明十二·1高层建筑增加费9层(30m)以下定额人工费×3%建筑物高度在6层或20m以上时见《解释》共性问题第7条12层(40m)以下定额人工费×5%15层(50m)以下定额人工费×7%18层(60m)以下定额人工费×9%21层(70m)以下定额人工费×11%24层(80m)以下定额人工费×12%27层(90m)以下定额人工费×15%30层(100m)以下定额人工费×18%33层(110m)以下定额人工费×23%36层(120m)以下定额人工费×27%39层(130m)以下定额人工费×32%42层(140m)以下定额人工费×35%45层(150m)以下定额人工费×39%48层(160m)以下定额人工费×42%51层(170m)以下定额人工费×45%54层(180m)以下定额人工费×49%57层(190m)以下定额人工费×51%60层(200m)以下定额人工费×54%其中人工占70%，其余为机械费。9.5P7说明九通风系统采用渐缩管按风管相应定额人工×2.509-1~15 9.6P7说明十空气幕送风管按风管相应定额人工×3.009-1~15 9.7《解释》九册-5轴流风机防雨短管制安按风管相应定额人工×3.09-1~12 9.8P121说明七分体式空调器“一拖多”机型，室内机安装按分体式空调器相应定额×0.669-415~428室内机区分不同安装形式9.9P121说明十四玻璃挡水板制作安装按钢板挡水板定额材料、机械×0.459-491~494人工不变9.10P121说明十五保温钢板密闭门制作安装按钢板密闭门定额材料×0.50，机械×0.459-489、490人工不变9.11P155说明六净化风管只在法兰处涂抹密封胶每10m2净化风管减去密闭胶1.5kg和0.37个工日9-503~506定额中净化风管接口外表面全部按涂密封胶考虑9.12P163说明五不锈钢风管及部件采用手工氩弧焊定额人工×1.238，材料×1.163，机械×1.6739-521~526 9.13P171说明三铝板风管及部件采用手工氩弧焊定额人工×1.154，材料×0.852，机械×9.2429-530~545 9.14《解释》九册-13设置于管道井、已封闭吊顶内通风空调系统安装定额人工×1.30全册 综合解释1、空调风管、冷媒水管所用的垫木均需防腐及防火处理，如何套用定额?答：垫木可按成品价格列入材料费。2、如果风机盘管进行单体试压，如何计取费用?答：此种检验属于新颁 规范 编程规范下载gsp规范下载钢格栅规范下载警徽规范下载建设厅规范下载 的要求，定额中没有考虑，可采用现场签证的方式处理。定额编号项目名称单位省价淄博价基价人工费材料费 第一章薄钢板通风管道制作安装      9-1镀锌钢板圆风管δ0.5内10728.50729.27510.70171.56　　镀锌钢板δ0.5　　　　11.389-2镀锌钢板圆风管δ0.8内10562.62559.90325.08201.71　　镀锌钢板δ0.75　　　　11.389-3镀锌钢板圆风管δ1.0内10462.62459.01248.26194.88　　镀锌钢板δ1　　　　11.389-4镀锌钢板圆风管δ1.2内10574.23569.56315.36244.47　　镀锌钢板δ1.2　　　　11.389-5镀锌钢板矩形风管δ0.5内10680.52678.26332.46294.23　　镀锌钢板δ0.5　　　　11.389-6镀锌钢板矩形风管δ0.8内10497.80494.80245.20219.49　　镀锌钢板δ0.75　　　　11.389-7镀锌钢板矩形风管δ1.0内10397.89394.34188.28189.64　　镀锌钢板δ1　　　　11.389-8镀锌钢板矩形风管δ1.2内10476.91471.87228.78230.91　　镀锌钢板δ1.2　　　11.38　9-9普通钢板圆形风管δ2内101095.891094.87602.78316.03　　普通钢板δ2　　　　10.809-10普通钢板圆形风管δ3内101268.121263.09676.91407.41　　普通钢板δ3　　　　10.809-11普通钢板矩形风管δ2内10942.28940.95465.08330.77　　普通钢板δ2　　　　10.809-12普通钢板矩形风管δ3内101134.741128.68527.58455.10　　普通钢板δ3　　　　10.809-13镀锌钢板矩形风管(插条)δ0.5内10387.31388.75257.04110.12　　镀锌钢板δ0.5　　　　11.509-14镀锌钢板矩形风管(插条)δ0.6内10322.22322.51222.1280.74　　镀锌钢板δ0.6　　　　11.509-15镀锌钢板矩形风管(插条)δ0.8内10278.34277.04187.5670.22　　镀锌钢板δ0.8　　　　11.509-16风机盘管连接管δ0.5内10843.11838.46392.15391.83　　镀锌钢板δ0.5　　　　12.259-17风机盘管连接管δ0.8内10686.62681.60315.43332.75　　镀锌钢板δ0.75　　　　12.259-18风机盘管连接管δ1.0内10694.20686.26296.28363.96　　镀锌钢板δ1　　　　12.259-19风机盘管连接管δ1.2内10712.05703.34316.87366.68　　镀锌钢板δ1.2　　　　12.259-20柔性软风管φ150内根19.1219.556.1612.77 9-21柔性软风管φ250内根25.5826.317.7817.84 9-22柔性软风管φ500内根37.0138.0310.7326.19 9-23柔性软风管φ710内根46.6147.9513.9732.67 9-24柔性软风管φ910内根58.1559.7217.9340.35 　20-24：柔性软风管根   　1.009-25弯头导流叶片103.79105.0054.0450.96 9-26软管接口219.11217.3883.16131.63 9-27风管检查孔T614hkg1710.691698.67766.08726.32 9-28温度.风量测定孔T615个37.5437.6220.8810.93 9-29支架制作安装50kg内hkg764.39752.04284.04440.26 9-30支架制作安装>50kghkg621.21609.08159.84433.49  第二章风管阀门制作安装      9-31空气加热器上通阀T101-11#个179.89178.6885.5083.76 9-32空气加热器上通阀T101-12#3#个240.27238.29109.44115.41 9-33空气加热器上通阀T101-14#个296.75294.04131.62145.28 9-34空气加热器上通阀T101-15#个272.39269.99121.97132.52 9-35空气加热器上通阀T101-16#个317.38314.40139.82156.13 9-36空气加热器上通阀T101-17#个367.99364.36159.84182.62 9-37空气加热器旁通阀T101-2Ⅰ710个149.05147.7372.1867.52 9-38空气加热器旁通阀T101-2Ⅰ1250个221.61219.35100.66105.81 9-39空气加热器旁通阀T101-2Ⅰ1750个284.58281.50125.64138.87 9-40空气加热器旁通阀T101-2Ⅱ710个185.10183.3186.4786.41 9-41空气加热器旁通阀T101-2Ⅱ1250个266.72263.88118.62129.50 9-42空气加热器旁通阀T101-2Ⅱ1750个348.20344.32150.84172.07 9-43空气加热器旁通阀T101-2Ⅲ710个189.39187.5388.1688.72 9-44空气加热器旁通阀T101-2Ⅲ1250个268.44265.58119.27130.40 9-45空气加热器旁通阀T101-2Ⅲ1750个342.89339.03148.68169.42 9-46空气加热器旁通阀T101-2Ⅳ710个230.10227.74104.33110.04 9-47空气加热器旁通阀T101-2Ⅳ1250个320.87317.34140.04157.86 9-48空气加热器旁通阀T101-2Ⅳ1750个411.15406.45175.82205.12 9-49圆形瓣式启动阀T301-5φ455内个590.10588.26244.30107.39 9-50圆形瓣式启动阀T301-5φ585内个751.25748.55305.93136.68 9-51圆形瓣式启动阀T301-5φ650内个937.47933.40367.85185.639-52圆形瓣式启动阀T301-5φ840内个1088.981076.96413.39260.88 定额编号项目名称单位省价淄博价基价人工费材料费9-53圆形瓣式启动阀T301-5φ910内个1205.101190.05440.89316.579-54圆形瓣式启动阀T301-5φ1040内个1454.951436.43546.37388.399-55圆形瓣式启动阀T301-5φ1300内个1955.301930.17721.76528.129-56圆形保温蝶阀T302-2φ250内个101.59101.2343.3428.079-57圆形保温蝶阀T302-2φ450内个154.78154.0870.4945.519-58圆形保温蝶阀T302-2φ630内个228.48224.9698.1779.119-59圆形保温蝶阀T302-2φ800内个324.77319.62140.40113.769-60圆形保温蝶阀T302-2φ1000内个451.85443.96198.61165.009-61圆形保温蝶阀T302-2φ1120内个582.65572.52256.43209.039-62方.矩形保温蝶阀T302-4.6Ｌ800个81.2080.8835.3926.439-63方.矩形保温蝶阀T302-4.6Ｌ1200个145.52144.9256.5942.279-64方.矩形保温蝶阀T302-4.6Ｌ1600个176.00175.0660.0161.399-65方.矩形保温蝶阀T302-4.6Ｌ2000个217.39214.0263.1190.379-66方.矩形保温蝶阀T302-4.6Ｌ2400个246.18242.1272.07107.499-67方.矩形保温蝶阀T302-4.6Ｌ2800个309.55304.4291.80134.929-68方.矩形保温蝶阀T302-4.6Ｌ3200个379.03372.26112.68172.309-69方.矩形保温蝶阀T302-4.6Ｌ4000个493.56484.67147.92221.349-70圆形蝶阀T302-1.7φ250内个97.5797.0350.7226.019-71圆形蝶阀T302-1.7φ450内个184.54183.4689.3945.219-72圆形蝶阀T302-1.7φ630内个267.65261.1889.6893.999-73圆形蝶阀T302-1.7φ800内个391.90382.14131.33139.539-74圆形蝶阀T302-1.7φ1000内个546.34531.84182.81201.459-75圆形蝶阀T302-1.7φ1120内个657.08639.88220.75236.889-76方.矩形蝶阀T302-3.5.8.9Ｌ800个87.5687.0232.5428.369-77方.矩形蝶阀T302-3.5.8.9Ｌ1200个143.61142.7648.0241.709-78方.矩形蝶阀T302-3.5.8.9Ｌ1600个195.50194.1469.9863.329-79方.矩形蝶阀T302-3.5.8.9Ｌ2000个249.73244.0374.5996.779-80方.矩形蝶阀T302-3.5.8.9Ｌ2400个310.83303.1294.64128.149-81方.矩形蝶阀T302-3.5.8.9Ｌ2800个373.16363.94115.42153.019-82方.矩形蝶阀T302-3.5.8.9Ｌ3200个481.90469.13150.16207.159-83方.矩形蝶阀T302-3.5.8.9Ｌ4000个634.73617.92198.47269.809-84圆形风管止回阀T303-1φ250内个112.93120.6140.0362.399-85圆形风管止回阀T303-1φ360内个158.23168.8255.9186.689-86圆形风管止回阀T303-1φ450内个194.81208.0466.71106.859-87圆形风管止回阀T303-1φ630内个275.51295.1285.36157.869-88圆形风管止回阀T303-1φ800内个362.04388.58105.59221.119-89圆形风管止回阀T303-1φ900内个422.16454.10122.62264.199-90方形风管止回阀T303-2Ｌ800内个112.87119.5435.2462.269-91方形风管止回阀T303-2Ｌ1000内个147.05155.3545.5078.639-92方形风管止回阀T303-2Ｌ1200内个177.78188.2455.0898.429-93方形风管止回阀T303-2Ｌ1600内个216.43229.7066.42124.349-94方形风管止回阀T303-2Ｌ2000内个296.90316.0083.70177.419-95方形风管止回阀T303-2Ｌ2400内个371.81394.8999.68234.889-96方形风管止回阀T303-2Ｌ3200内个487.98518.55134.21312.399-97密闭式斜插板阀T309φ120内个79.8579.1442.3728.919-98密闭式斜插板阀T309φ160内个112.23111.1259.1540.499-99密闭式斜插板阀T309φ200内个133.79132.2764.7352.509-100密闭式斜插板阀T309φ250内个158.16155.8065.3472.979-101密闭式斜插板阀T309φ300内个209.74206.6372.2296.009-102密闭式斜插板阀T309φ340内个268.63264.7494.75119.029-103矩形风管三通调节阀T310-1.2800个57.0056.8631.2113.139-104矩形风管三通调节阀T310-1.21200个73.7873.5940.6116.699-105矩形风管三通调节阀T310-1.21400个93.1992.9351.5520.759-106矩形风管三通调节阀T310-1.21600个110.31110.0260.9124.799-107矩形风管三通调节阀T310-1.21800个122.07121.7467.1427.769-108矩形风管三通调节阀T310-1.22000个143.95143.5379.6731.899-109矩形风管三通调节阀T310-1.22460个196.21195.60109.3342.619-110矩形风管三通调节阀T310-1.22760个229.93229.23128.0950.029-111对开多叶调节阀T311Ｌ1600内个261.88261.9693.38100.079-112对开多叶调节阀T311Ｌ2400内个392.63392.15144.36142.369-113对开多叶调节阀T311Ｌ3200内个607.11599.87171.79278.529-114对开多叶调节阀T311Ｌ4000内个802.97792.92232.16357.239-115对开多叶调节阀T311Ｌ5200内个1203.431187.94346.46539.149-116对开多叶调节阀T311Ｌ6500内个1604.631583.77461.30722.769-117空气加热器上通阀个62.6962.9541.0420.529-118空气加热器旁通阀个29.7629.8827.002.889-119圆形瓣式启动阀φ600内个44.1344.3036.726.949-120圆形瓣式启动阀φ800内个58.2558.2546.0811.539-121圆形瓣式启动阀φ1000内个87.7988.2956.5219.649-122圆形瓣式启动阀φ1300内个114.46114.9675.2421.899-123蝶阀止回阀插板阀多叶调节阀800个11.6511.757.563.959-124蝶阀止回阀插板阀多叶调节阀1600个34.4834.6110.805.989-125蝶阀止回阀插板阀多叶调节阀2400个54.0154.1818.728.359-126蝶阀止回阀插板阀多叶调节阀3200个72.3672.5725.2011.70定额编号项目名称单位省价淄博价未计价材基价人工费材料费9-127蝶阀止回阀插板阀多叶调节阀4000个98.3098.5534.5614.06 9-128蝶阀止回阀插板阀多叶调节阀5200个123.72123.7241.4722.33 9-129蝶阀止回阀插板阀多叶调节阀6500个145.36145.3648.3827.08 　117-129：调节阀个   　1.009-130风管防火阀周长2200内个135.01135.0162.1043.64 9-131风管防火阀周长3600内个176.76176.4370.1360.61 9-132风管防火阀周长5400内个315.40313.58121.10126.57 9-133风管防火阀周长8000内个436.28433.62173.02166.87 　130-133：风管防火阀个   　1.009-134余压阀周长1200内个100.8799.9040.1854.31 9-135余压阀周长1600内个177.45176.1260.0573.88 9-136余压阀周长2400内个232.66230.8077.94106.16 　134-136：余压阀个   　1.009-137风阀电(气)动执行机构套100.37100.3161.6334.37 　连杆组件套   　1.00 第三章　风口制作安装      9-138带调节板活动百叶风口300X150个70.7070.7446.6916.83 9-139带调节板活动百叶风口450X225个98.5898.3962.1427.55 9-140带调节板活动百叶风口600X300个141.48141.0590.5438.08 9-141单层百叶风口T202-2300X150内个48.5848.4134.6713.29 9-142单层百叶风口T202-2400X240内个81.0880.4057.8222.01 9-143单层百叶风口T202-2550X375内个106.72105.6869.1935.83 9-144双层百叶风口T202-2300X150内个76.7776.3753.5322.09 9-145双层百叶风口T202-2400X240内个135.87135.1395.5838.38 9-146双层百叶风口T202-2550X375内个164.52163.1497.5664.07 9-147三层百叶风口T202-3290X180内个96.8296.3259.4733.94 9-148三层百叶风口T202-3410X250内个149.90149.1294.0752.09 9-149三层百叶风口T202-3570X320内个202.63201.48119.6678.05 9-150连动百叶风口T202-4300X195内个81.8781.6345.8619.26 9-151连动百叶风口T202-4350X285内个115.06114.7466.0226.86 9-152连动百叶风口T202-4500X375内个154.77154.2690.2540.46 9-153矩形送风口T203100X87内个69.1168.8642.6224.45 9-154矩形送风口T203160X139内个92.6091.7246.4042.47 9-155矩形送风口T203200X173内个125.66124.3563.3257.12 9-156矩形空气分布器T206-1.2300X150个135.65134.9068.2260.69 9-157矩形空气分布器T206-1.2500X250个212.65211.35104.1897.29 9-158矩形空气分布器T206-1.2700X350个379.91377.32182.02176.62 定额编号项目名称单位省价淄博价基价人工费材料费9-159风管插板风口T208-1.2周长660内个12.0811.976.984.679-160风管插板风口T208-1.2周长840内个15.9115.727.567.769-161风管插板风口T208-1.2周长1200内个20.9020.649.0411.129-162风管插板风口T208-1.2周长1680内个26.8726.529.9016.149-163旋转吹风口T209-1.21#/250内个194.04192.2566.7894.209-164旋转吹风口T209-1.22#/280内个223.15221.0675.96108.329-165旋转吹风口T209-1.23#/320内个266.89264.3090.65128.919-166旋转吹风口T209-1.24#/360内个334.92331.81117.50160.239-167旋转吹风口T209-1.25#/400内个379.17375.54131.69181.519-168旋转吹风口T209-1.26#/450内个449.05444.54154.55214.579-169圆形直片散流器CT211-12#/140个115.17114.4665.5927.709-170圆形直片散流器CT211-15#/250个191.23190.01109.5545.209-171圆形直片散流器CT211-18#/360个263.41261.42131.0472.759-172圆形直片散流器CT211-110#/450个350.74348.10174.2497.069-173圆形直片散流器CT211-111#/500个381.24378.35188.89105.689-174方形直片散流器CT211-2160X160个98.8798.2659.1123.399-175方形直片散流器CT211-2250X250个153.87152.6377.9844.949-176方形直片散流器CT211-2400X400个252.45250.49126.4374.179-177方形直片散流器CT211-2500X500个339.09336.44167.76100.439-178流线形散流器CT211-41#/160内个143.97143.1585.3232.249-179流线形散流器CT211-42#/200内个194.35193.15114.7343.169-180流线形散流器CT211-43#/250内个279.78277.96166.6160.839-181流线形散流器CT211-44#/320内个361.59359.20213.7079.599-182单面送吸风口T212-1周长640内个50.1449.5925.9922.499-183单面送吸风口T212-1周长800内个65.6564.8533.5229.919-184单面送吸风口T212-1周长1000内个111.71110.2656.4551.899-185单面送吸风口T212-1周长1280内个131.17129.1552.6774.149-186单面送吸风口T212-1周长1600内个180.51177.5069.59105.169-187单面送吸风口T212-1周长2000内个264.06259.55103.00152.659-188双面送吸风口T212-2周长640内个53.7553.2831.5420.659-189双面送吸风口T212-2周长800内个67.9767.3339.7426.239-190双面送吸风口T212-2周长1000内个110.50109.3964.0443.319-191双面送吸风口T212-2周长1280内个145.15143.5076.5464.119-192双面送吸风口T212-2周长1600内个188.81186.4697.9286.269-193双面送吸风口T212-2周长2000内个240.69237.23111.20122.849-194活动箅板式风口T261周长1200内个90.5190.4360.6610.409-195活动箅板式风口T261周长1600内个119.14118.9881.7915.969-196活动箅板式风口T261周长2000内个136.78136.4891.3320.659-197活动箅板式风口T261周长2400内个169.93169.51113.4428.959-198活动箅板式风口T261周长2600内个188.61188.11125.4232.349-199网式矩形风口T2623#/350X250内个30.2930.4417.1011.639-200网式矩形风口T2625#/550X350内个64.6264.8639.8522.139-201网式矩形风口T2628#/800X500内个74.8475.1341.9430.799-202网式三面风口T2622#/300X200内个79.1579.5633.1941.499-203网式三面风口T2624#/500X250内个141.14141.7461.9271.089-204网式三面风口T2626#/620X300内个185.93186.6883.2392.239-205单百叶风口135型CT263-1190X150个56.2855.0640.6113.999-206单百叶风口135型CT263-1310X240个99.1996.8671.4624.779-207单百叶风口135型CT263-1490X390个171.78166.10111.7153.229-208单百叶风口135型CT263-1615X490个215.16207.76138.6767.639-209单百叶风口135型CT263-1775X620个297.41286.95192.1392.879-210单百叶风口135型CT263-1975X620个391.20376.85252.07122.209-211双百叶风口135型CT263-1190X150个83.3080.8558.0022.119-212双百叶风口135型CT263-1310X240个139.12134.8896.4137.399-213双百叶风口135型CT263-1490X390个239.94231.35156.9672.449-214双百叶风口135型CT263-1615X490个318.60305.59199.04104.169-215双百叶风口135型CT263-1775X620个373.28355.74213.66138.959-216双百叶风口135型CT263-1975X620个499.05474.52281.77188.479-217带导流片百叶风口135型190X150个89.8687.0862.0624.289-218带导流片百叶风口135型310X240个152.68147.80105.1941.509-219带导流片百叶风口135型490X390个225.84215.52127.3086.399-220带导流片百叶风口135型615X490个321.22305.60180.94122.029-221带导流片百叶风口135型775X620个442.81421.00249.41168.019-222带导流片百叶风口135型975X620个555.56527.64311.00212.129-223钢百叶窗风口J718-10.5内个218.44215.8573.37124.139-224钢百叶窗风口J718-11内个316.05312.23110.92179.129-225钢百叶窗风口J718-11.5内个477.85472.03170.32268.439-226钢百叶窗风口J718-12.0内个628.23620.43218.88357.189-227钢百叶窗风口J718-13.0内个830.47819.17264.67502.139-228钢百叶窗风口J718-14.0内个1094.871079.57342.61667.149-229活动金属百叶风口T718-1479.82470.01349.20119.379-230条缝形风口KS-11600X100个164.28163.02106.0655.889-231条缝形风口KS-111200X100个315.43312.82204.52106.389-232条缝形风口KS-112000X100个506.99502.78328.43171.35定额编号项目名称单位省价淄博价未计价材基价人工费材料费9-233百叶风口安装800内个10.4910.586.843.50 9-234百叶风口安装1200内个14.2014.378.755.38 9-235百叶风口安装1600内个25.3325.5416.888.42 9-236百叶风口安装2400内个36.4936.7425.4211.08 9-237百叶风口安装3200内个47.5047.8332.9014.69 9-238百叶风口安装>3200个57.0257.4339.4917.65 　233-238：百叶风口个   　1.009-239矩形送风口安装400内个8.949.115.443.67 9-240矩形送风口安装600内个10.7010.876.953.92 9-241矩形送风口安装800内个12.6512.828.754.07 　239-241：矩形送风口个   　1.009-242矩形空气分布器安装1200内个23.1723.2519.084.17 9-243矩形空气分布器安装1500内个28.1728.3022.325.98 9-244矩形空气分布器安装2100内个34.1234.2826.647.64 　242-244：矩形空气分布器个   　1.009-245旋转吹风口安装φ320内个29.4929.6116.9212.69 9-246旋转吹风口安装φ450内个47.4047.5228.0819.44 　245-246：旋转吹风口个   　1.009-247方.圆形散流器安装500内个8.999.037.201.83 9-248方.圆形散流器安装1000内个14.5714.6412.242.40 9-249方.圆形散流器安装2000内个20.6520.7715.844.93 　247-249：散流器个   　1.009-250条缝形风口(分布器)ｍ31.2131.3621.499.63 　条缝形风口(分布器)ｍ   　1.009-251活动箅板式风口安装1330内个13.6513.7412.600.50 9-252活动箅板式风口安装1910内个15.9416.0414.760.56 9-253活动箅板式风口安装2590内个20.0520.1918.720.67 　251-253：活动箅式风口个   　1.009-254钢百叶窗安装0.5内个14.6014.9711.992.98 9-255钢百叶窗安装1内个20.9821.4317.783.65 9-256钢百叶窗安装2内个35.9136.4930.825.67 9-257钢百叶窗安装4内个38.9639.6832.657.03 　254-257：钢百叶窗个   　1.009-258多叶排烟口1200内个105.42104.7763.9438.39 9-259多叶排烟口1600内个124.95124.1575.3546.00 9-260多叶排烟口2400内个211.93210.25121.2883.47 9-261多叶排烟口2800内个262.06260.11153.43100.37 9-262多叶排烟口3200内个292.61290.44172.12111.43 9-263多叶排烟口4000内个420.91417.00220.82184.34 　258-263：多叶排烟口个   　1.009-264多叶排烟口带远控装置1200个167.20165.90113.6549.81 9-265多叶排烟口带远控装置1600个186.73185.28125.0657.42 9-266多叶排烟口带远控装置2400个277.38275.05171.0098.55 9-267多叶排烟口带远控装置2800个323.85321.25203.15111.79 9-268多叶排烟口带远控装置3200个354.40351.57221.83122.85 9-269多叶排烟口带远控装置4000个482.67478.10270.50195.76 　264-269：多叶排烟口个   　1.00　远程控制器(带盒)个   　1.00　镀锌钢管DN20ｍ    (─)　钢丝绳φ6ｍ    (─)9-270板式排烟口带远控装置1200个141.83140.6395.8342.85 9-271板式排烟口带远控装置1600个151.63150.2997.7050.31 9-272板式排烟口带远控装置2400个187.11185.56118.2264.25 9-273板式排烟口带远控装置2800个215.30213.57135.0774.73 9-274板式排烟口带远控装置3200个277.17274.65160.52108.17 9-275板式排烟口带远控装置4000个322.81319.88182.09130.52 　270-275：板式排烟口个    1.00　远程控制器(带盒)个    1.00　镀锌钢管DN20ｍ    　钢丝绳φ6ｍ    (─) 第四章风帽制作安装      9-276圆伞形风帽T6093#/250内个192.83193.7561.09131.15 9-277圆伞形风帽T6095#/320内个250.58251.8182.30167.60 9-278圆伞形风帽T6097#/400内个326.91328.20111.10214.47 9-279圆伞形风帽T60910#/560内个415.19415.39114.52297.81 9-280圆伞形风帽T60912#/700内个544.81544.04151.13389.46 9-281圆伞形风帽T60913#/800内个704.04700.77176.80519.22 9-282圆伞形风帽T60914#/900内个816.53811.62202.43604.31 9-283圆伞形风帽T60915#/1000内个940.12933.55228.06699.50 9-284圆伞形风帽T60916#/1120内个1118.811109.77271.37831.03 9-285圆伞形风帽T60917#/1250内个1296.791285.22312.44964.14 9-286锥形风帽T6103#/250内个338.44336.89107.35223.76 9-287锥形风帽T6105#/320内个460.73458.47150.77300.38 9-288锥形风帽T6107#/400内个557.19553.43155.41389.31 定额编号项目名称单位省价淄博价基价人工费材料费9-289锥形风帽T61010#/560内个864.92856.45249.48597.709-290锥形风帽T61012#/700内个1212.221198.78354.38833.479-291锥形风帽T61013#/800内个1498.411478.66399.821066.229-292锥形风帽T61014#/900内个1813.451788.20486.431289.199-293锥形风帽T61015#/1000内个2123.642092.78569.951509.479-294锥形风帽T61016#/1120内个2583.942544.84695.451833.079-295锥形风帽T61017#/1250内个3082.723034.55828.722186.319-296筒形风帽T6112#/200内个258.23257.9882.12173.879-297筒形风帽T6113#/280内个350.92349.67114.84231.979-298筒形风帽T6114#/400内个545.58543.75182.99356.769-299筒形风帽T6115#/500内个806.99799.77222.44572.269-300筒形风帽T6116#/630内个1087.801076.64295.38775.199-301筒形风帽T6117#/700内个1251.631238.14339.26892.069-302筒形风帽T6118#/800内个1386.381370.21343.151019.289-303筒形风帽T6119#/900内个1889.131864.09460.441394.749-304筒形风帽T61110#/1000内个2186.972156.90530.241616.88 第五章罩类制作安装     9-305皮带防护罩T108B式hkg2190.202184.981455.37613.359-306皮带防护罩T108C式hkg1840.051834.841117.87664.109-307电机防雨罩T110hkg1339.681314.17406.58857.429-308上吸式侧吸罩T401-1.2hkg1097.281090.44420.48655.149-309下吸式侧吸罩T401-1.2hkg1067.681061.05369.58676.659-310中小型零件焊接台排气罩T401-3hkg1278.491272.59551.70710.469-311整体.分组式槽边侧吸罩T403-1hkg1265.031203.54492.95660.989-312吹.吸式槽边通风罩94T459hkg1280.261219.17497.81667.939-313各型风罩调节阀hkg1292.101250.92411.01590.509-314条缝槽边抽风罩86T414hkg1335.511257.42483.41720.589-315泥心烘炉排气罩T407-1hkg1160.691156.19540.65586.169-316升降式回转排气罩T409hkg1986.931981.191361.66616.739-317墙.砼柱上下吸式圆形回转罩T410hkg942.68933.51370.30559.509-318钢柱上下吸式圆形回转罩T410hkg813.85791.96201.89583.439-319升降式排气罩T412hkg833.16815.69308.48446.219-320手锻炉排气罩T413hkg937.91883.20256.90594.779-321镀锌钢板排气罩制安2400内275.32276.35134.60138.179-322镀锌钢板排气罩制安4000内213.07222.3287.34132.209-323镀锌钢板排气罩制安5600内168.26169.8446.87121.369-324不锈钢排气罩安装84.5184.1951.8031.13定额编号项目名称单位省价淄博价未计价材基价人工费材料费　不锈钢排气罩   　1.00 第六章消声器制作安装      9-325片式消声器T701-11#组10119.7910023.272725.816562.12 9-326片式消声器T701-12#组13787.6113670.593671.069023.91 9-327片式消声器T701-13#组17431.2517281.964618.7311447.51 9-328片式消声器T701-14#组24760.1324566.436512.1816358.34 9-329矿棉管式消声器T701-21#组330.89314.63129.92163.91 9-330矿棉管式消声器T701-22#4#组388.93369.70153.14192.21 9-331矿棉管式消声器T701-23#7#组447.13424.91176.80220.23 9-332矿棉管式消声器T701-25#组464.11441.10183.10229.15 9-333矿棉管式消声器T701-26#8#组535.66508.96212.22263.49 9-334矿棉管式消声器T701-29#组623.23591.98247.61305.75 9-335聚酯泡沫管式消声器T701-31#组226.13213.4646.33163.59 9-336聚酯泡沫管式消声器T701-32#组264.01249.0454.43190.65 9-337聚酯泡沫管式消声器T701-33#组302.98285.7462.64218.71 9-338聚酯泡沫管式消声器T701-36#组354.60334.3473.55255.85 9-339聚酯泡沫管式消声器T701-39#组405.24381.9184.46291.96 9-340卡普隆纤维管式消声器T701-41#组321.74301.99111.31176.55 9-341卡普隆纤维管式消声器T701-42#组370.97348.03128.95202.88 9-342卡普隆纤维管式消声器T701-45#组431.92405.71153.07233.64 9-343卡普隆纤维管式消声器T701-43#组419.52394.15148.36227.37 9-344卡普隆纤维管式消声器T701-46#组504.40472.97176.33274.90 9-345卡普隆纤维管式消声器T701-49#组581.25544.78204.19315.63 9-346弧形声流式消声器T701-51#组6245.225949.962439.142949.86 9-347弧形声流式消声器T701-52#组8663.218252.623389.184085.25 9-348阻抗复合式消声器T701-61#组1212.571144.02480.89650.04 9-349阻抗复合式消声器T701-62#组1409.341329.69559.55754.84 9-350阻抗复合式消声器T701-63#组1754.601654.47698.04938.20 9-351阻抗复合式消声器T701-64#组1952.441841.01777.061043.88 9-352阻抗复合式消声器T701-65#组1618.471527.03641.70868.37 9-353阻抗复合式消声器T701-66#组1798.241695.91714.35962.98 9-354阻抗复合式消声器T701-67#组2270.702142.63902.161216.10 9