单臂路由实验详解
我是一名正在学习NA的学员 本来是小白 学习NA的时候遇到的困难不是一点半点 所以把NA中的实验难点发给大家 希望大家一起提高
PC 配置
配置IP 地址 子网掩码 网关 这是很基本的东西 不用多说
交换机配置
Switch>
Switch>en
Switch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#vlan 2 配置VLAN2
Switch(config...
我是一名正在学习NA的学员 本来是小白 学习NA的时候遇到的困难不是一点半点 所以把NA中的实验难点发给大家 希望大家一起提高
PC 配置
配置IP 地址 子网掩码 网关 这是很基本的东西 不用多说
交换机配置
Switch>
Switch>en
Switch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#vlan 2 配置VLAN2
Switch(config-vlan)#exit
Switch(config)#vlan 3 配置VLAN3
Switch(config-vlan)#exit
Switch(config)#int fa 0/1 把端口加入到VLAN
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 2
Switch(config-if)#int fa 0/2
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 3
Switch(config-if)#exit
Switch(config)#int fa 0/4 设置 Trunk
Switch(config-if)#switchport access trunk
^
% Invalid input detected at '^' marker.
Switch(config-if)#switchport mode trunk
Switch(config-if)#exit
Switch(config)#exit
Switch#
%SYS-5-CONFIG_I: Configured from console by console
Switch#show int fa 0/4 switchport 查看Trunk端口
Name: Fa0/4
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: Off
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Protected: false
Appliance trust: none
Switch#
路由器配置、
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa 0/0
Router(config-if)#no shutdown 打开路由器
Router(config-if)#exit
Router(config)#int fa 0/0.? 查看子接口
<0-4294967295> FastEthernet interface number
Router(config)#int fa 0/0.1 配置子接口
Router(config-subif)#encapsulation dot1q 2 封装给vlan2
Router(config-subif)#ip add 192.168.1.1 255.255.255.0
Router(config-subif)#no shutdown
Router(config-subif)#int fa 0/0.3
%LINK-5-CHANGED: Interface FastEthernet0/0.3, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.3, changed state to up
Router(config-subif)#encapsulation dot1q 3 封装协议给vlan3
%Configuration of multiple subinterfaces of the same main
interface with the same VID (3) is not permitted.
This VID is already configured on FastEthernet0/0.5.
Router(config-subif)#ip add 192.168.2.1 255.255.255.0
% Configuring IP routing on a LAN subinterface is only allowed if that
subinterface is already configured as part of an IEEE 802.10, IEEE 802.1Q,
or ISL vLAN.
Router(config-subif)#no shutdown
Router(config-subif)#exit]
^
% Invalid input detected at '^' marker.
Router(config-subif)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
本文档为【单臂路由实验详解】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑,
图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。