PFI ES-3-2000 预制管件精度公差Fabricating Tolerances

~ STD.PFI ES-3-ENGL 2000 7Lb4544 00005LL bT8 D PFI Standard ES-3 (Reaffimied September 2000) FABRICATING TOLERANCES Prepared by Pipe Fabrication Institute Engineering Committee All PFI Standards are advisory only. There is no agreement to adhere to any PFI Standard and their use by anyone is entirely voluntary. Copyright by PIPE FABRICATION INSTITUTE Dedirnted io Teclinicnl Adiwnceinenis nnd Stondnrdizntion in rlie Pipe Fnbricniioii lridiisii.). Since i913 USA CANADA PMB 323 Woshinglon. DC 20003 655. 32"" ove. sirite 201 H8T3G6 61 I Pennsjhmia Averiire SE Lnrkine. Qirebec WEB SITE /zttp://iMi?ii.pfi-insfi/i~te. org COPYRIGHT Pipe Fabrication Institute Licensed by Information Handling Services COPYRIGHT Pipe Fabrication Institute Licensed by Information Handling Services PFI Standard ES-3 (Reaffirmed September 2000) FABRICATING TOLERANCES METRIC CONVERSIONS The conversion of quantities between systems of units involves a determination of the number of significant digits to be retained. All conversions depend upon the intended precision of the original quantity and are rounded to the appropriate accuracy. Pipe sizes together with applicable wall thickness are not shown with metric equivalents. The SI (metric) values where included with the customary U.S. values in this Standard are the rounded equivalents of the U.S. values and are for reference only. Metric units were derived utilizing the following conversion factor: Conversion Factor inches to 25.4 millimeter 1. Scope 1.1 This standard covers general pipe shop fabricating tolerances for prefabricated piping assemblies. 2. Linear Tolerances 2.1 The tolerances on linear dimensions (intermediate or overall) apply to the face to face, face to end, and end to end measurements of fabricated straight pipe and headers; center'to end or center to face of nozzles or other attachments; or center to face of bends; as illustrated on Fig. 1. These tolerances are not accumulative. excess of those specified in paragraphs 2.2 and 2.3 may occur. 3. Angularity and Rotation Tolerances 3.1 Angularity tolerance across the face of flanges, weld end preparation and on rotation of flanges are as stated on Fig. 1. 4. Closer Tolerances 4.1 When closer tolerances than those given in paragraphs 2.2, 2.3 and 2.4 are absolutely necessary, they shall be subject to agreement between the Purchaser and Fabricator. 2.2 Linear tolerances on "A" are k 1/8" (3.0 mm) for sizes 10" and under, k 3/16" (5.0 mm) for sizes 12" through 24" and I 1/4" (6.0 mm) for sizes over 24" through 36". 2.3 Linear tolerances on "A" for sizes over 36" are subject to tolerances o f f 1/4" (6.0 mm), increasing by plus or minus 1/16" (2.0 mm) for each 12" in diameter over 36". 2.4 Due to the cumulative effects of tolerances on fittings or flanges, when joined without intervening pipe segments, deviations in 2 COPYRIGHT Pipe Fabrication Institute Licensed by Information Handling Services COPYRIGHT Pipe Fabrication Institute Licensed by Information Handling Services ~ ~ S T D - P F I ES-1-ENGL 2000 71b4544 0000513 470 4 "A" b FOR BENDING TOLERANCE, MINIMUM RADIUS AND MINIMUM TANGENT SEE PFI STANDARD ES-24 TOLERANCES ON DIMENSIONS WHICH Do NOT INCLUDE PIPE SEGMENTS ARE TO BE BASED ON ANSI SPECIFICATIONS FOR FITTINGS OR FLANGES INVOLVED (SEE PARAGRAPH 2.4) ROTATION OF FLANGES FROM THE INDICATED POSITION MEASURED AS SHOWN, 1/16' (2.0 mrn) MAX APPLICATION OF PIPE FABRICATION TOLERANCES 3 I SECTION X-X L ALIGNMENT OF FACINGS OR ENDS SHALL NOT DEVIATE FROM THE INDICATED POSITION MEASURED ACROSS ANY DIAMETER MORE THAN 3/64" PER FOOT (1.0 mm PER 25.0 cm) OR 1/32" (1 .O mm) WHICHEVER IS GREATER L (3.0 mm) COPYRIGHT Pipe Fabrication Institute Licensed by Information Handling Services COPYRIGHT Pipe Fabrication Institute Licensed by Information Handling Services ~ STD-PFI ES-3-ENGL 2000 = 7Lb4544 OOOCI5L ' i 307 CHARTER MEMBERS ACCORD PIPE FABRICATORS, INC. AIR CONDITIONING COMPANY, INC. FLO-RITE, INC. GEM INDUSTRIAL, INC. HPI CONSTRUCTION CO., INC. HUXTABLE & ASSOCIATES, INC. IDEAL WELDERS, LTD. INDUSTRIAL POWER SYSTEMS, INC. IVOR J. LEE, INC. JOHN E. GREEN COMPANY J. F. AHERN CO. J. H. KELLY LLC J. S. MC KINNEY, INC. KINETIC SYSTEMS, INC. M & M WELDING AND FABRICATORS, INC. MC ABEE CONSTRUCTION, INC. MC CARL'S, INC. MECHANICAL INCORPORATED MID STATES PIPE FABRICATING, INC. MURPHY COMPANY NARDE1 FABRICATORS, LTD. NEWMECH COMPANIES, INC. PHILLIPS, GETSCHOW COMPANY PIPING SYSTEMS, INC. S. A. COMUNALE COMPANY, INC. S&D I OSTERFELD MECHANICAL CONTRACTORS SCOTT CO. OF CALIFORNIA SPECIALTY PIPING CORPORATION TEAM INDUSTRIES, INC. W. J. O'NEIL COMPANY Jamaica, Glendale, Riviera Beach, Wal bridge, Huntington, Lawrence, Delta, Toledo, Masury, Highland Park, Fond du Lac, Longview, Freeport, Santa Clara, Gaithersburg, Tuscaloosa, Beaver Falls, Freeport, EI Dorado, St. Louis, Calgary, St. Paul, Oconto Falls, New London, Barberton, Dayton, San Leandro, Davisville, Kau kauna, Livon ia, New York California Florida Ohio West Virginia Kansas British Columbia (Canada) Ohio Ohio Michigan Wisconsin Washington Texas California Maryland Alabama Pennsylvania Illinois Arkansas Missouri Alberta (Canada) Minnesota Wisconsin Wisconsin Ohio Ohio California West Virginia Wisconsin Michigan A current index of the latest revised ES Standards, Technical Bulletins and Safety Training Guideline is available from the Pipe Fabrication Institute. PFI Safety Training Guideline, Standards and Technical Bulletins are published to serve proven needs of the pipe fabricating industry at the design level and in actual shop operations. Hence, such needs are continually considered and reviewed by the Engineering Committee of the Pipe Fabrication Institute to provide recommended procedures, which have been demonstrated by collective experiences to fiilfill requirements in a manner for Code compliance. However, as the PFI Standards are for minimum requirements the designer or fabricator always has the option of specifying supplementary conditions in the form of requirements beyond the scope of the PFI publications. COPYRIGHT Pipe Fabrication Institute Licensed by Information Handling Services COPYRIGHT Pipe Fabrication Institute Licensed by Information Handling Services