LM158 258 358 2904

LM158/LM258/LM358/LM2904 Low Power Dual Operational Amplifiers October 2005 LM158/LM258/LM358/LM2904 Low Power Dual Operational Amplifiers General Description The LM158 series consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. Application areas include transducer amplifiers, dc gain blocks and all the conventional op amp circuits which now can be more easily implemented in single power supply systems. For example, the LM158 series can be directly operated off of the standard +5V power supply voltage which is used in digital systems and will easily provide the required interface electronics without requiring the additional ± 15V power supplies. The LM358 and LM2904 are available in a chip sized package (8-Bump micro SMD) using National’s micro SMD package technology. Advantages n Two internally compensated op amps n Eliminates need for dual supplies n Allows direct sensing near GND and VOUT also goes to GND n Compatible with all forms of logic n Power drain suitable for battery operation Features n Available in 8-Bump micro SMD chip sized package, (See AN-1112) n Internally frequency compensated for unity gain n Large dc voltage gain: 100 dB n Wide bandwidth (unity gain): 1 MHz (temperature compensated) n Wide power supply range: — Single supply: 3V to 32V — or dual supplies: ± 1.5V to ± 16V n Very low supply current drain (500 µA) — essentially independent of supply voltage n Low input offset voltage: 2 mV n Input common-mode voltage range includes ground n Differential input voltage range equal to the power supply voltage n Large output voltage swing Unique Characteristics n In the linear mode the input common-mode voltage range includes ground and the output voltage can also swing to ground, even though operated from only a single power supply voltage. n The unity gain cross frequency is temperature compensated. n The input bias current is also temperature compensated. Voltage Controlled Oscillator (VCO) 00778723 © 2005 National Semiconductor Corporation DS007787 www.national.com LM158/LM258/LM358/LM2904 Absolute Maximum Ratings (Note 9) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. LM158/LM258/LM358 LM158A/LM258A/LM358A Supply Voltage, V+ Differential Input Voltage Input Voltage Power Dissipation (Note 1) Molded DIP Metal Can Small Outline Package (M) micro SMD Output Short-Circuit to GND (One Amplifier) (Note 2) V+ ≤ 15V and TA = 25˚C Input Current (VIN < −0.3V) (Note 3) Operating Temperature Range LM358 LM258 LM158 Storage Temperature Range Lead Temperature, DIP (Soldering, 10 seconds) Lead Temperature, Metal Can (Soldering, 10 seconds) Soldering Information Dual-In-Line Package Soldering (10 seconds) Small Outline Package Vapor Phase (60 seconds) Infrared (15 seconds) 215˚C 220˚C 260˚C 300˚C 260˚C 0˚C to +70˚C −25˚C to +85˚C −55˚C to +125˚C −65˚C to +150˚C Continuous 50 mA 830 mW 550 mW 530 mW 435mW 32V 32V −0.3V to +32V LM2904 26V 26V −0.3V to +26V 830 mW 530 mW Continuous 50 mA −40˚C to +85˚C −65˚C to +150˚C 260˚C 300˚C 260˚C 215˚C 220˚C See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering surface mount devices. ESD Tolerance (Note 10) 250V 250V Electrical Characteristics V+ = +5.0V, unless otherwise stated Parameter Input Offset Voltage Input Bias Current Input Offset Current Input Common-Mode Voltage Range Supply Current Conditions (Note 5), TA = 25˚C IIN(+) or IIN(−), TA = 25˚C, VCM = 0V, (Note 6) IIN(+) − IIN(−), VCM = 0V, TA = 25˚C V+ = 30V, (Note 7) (LM2904, V+ = 26V), TA = 25˚C Over Full Temperature Range RL = ∞ on All Op Amps V+ = 30V (LM2904 V+ = 26V) V+ = 5V 1 0.5 2 1.2 1 0.5 2 1.2 1 0.5 2 1.2 mA mA 0 2 10 V+−1.5 0 5 30 V+−1.5 0 3 30 V+−1.5 nA V LM158A Min Typ 1 20 Max 2 50 LM358A Min Typ 2 45 Max 3 100 LM158/LM258 Min Typ 2 45 Max 5 150 mV nA Units www.national.com 2 LM158/LM258/LM358/LM2904 Electrical Characteristics V+ = +5.0V, unless otherwise stated Parameter Input Offset Voltage Input Bias Current Input Offset Current Input Common-Mode Voltage Range Supply Current Conditions Min (Note 5) , TA = 25˚C IIN(+) or IIN(−), TA = 25˚C, VCM = 0V, (Note 6) IIN(+) − IIN(−), VCM = 0V, TA = 25˚C V = 30V, (Note 7) (LM2904, V+ = 26V), TA = 25˚C Over Full Temperature Range RL = ∞ on All Op Amps V+ = 30V (LM2904 V+ = 26V) V+ = 5V 1 0.5 2 1.2 1 0.5 2 1.2 mA mA + LM358 Typ 2 45 5 0 Max 7 250 50 V −1.5 + LM2904 Min Typ 2 45 5 0 Max 7 250 50 V −1.5 + Units mV nA nA V Electrical Characteristics V+ = +5.0V, (Note 4), unless otherwise stated Parameter Large Signal Voltage Gain Common-Mode Rejection Ratio Power Supply Rejection Ratio Amplifier-to-Amplifier Coupling Output Current Conditions V+ = 15V, TA = 25˚C, RL ≥ 2 kΩ, (For VO = 1V to 11V) TA = 25˚C, VCM = 0V to V+−1.5V V+ = 5V to 30V (LM2904, V+ = 5V to 26V), TA = 25˚C f = 1 kHz to 20 kHz, TA = 25˚C (Input Referred), (Note 8) Source VIN+ = 1V, VIN− = 0V, V+ = 15V, VO = 2V, TA = 25˚C Sink VIN− = 1V, VIN+ = 0V V+ = 15V, TA = 25˚C, VO = 2V VIN− = 1V, VIN+ = 0V TA = 25˚C, VO = 200 mV, V+ = 15V Short Circuit to Ground Input Offset Voltage Input Offset Voltage Drift Input Offset Current Input Offset Current Drift Input Bias Current Input Common-Mode Voltage Range IIN(+) or IIN(−) V = 30 V, (Note 7) (LM2904, V+ = 26V) + LM158A Min Typ 50 100 Max LM358A Min Typ 25 100 Max LM158/LM258 Min Typ 50 100 Max Units V/mV 70 85 65 85 70 85 dB 65 100 65 100 65 100 dB −120 −120 −120 dB 20 40 20 40 20 40 mA 10 20 10 20 10 20 mA 12 50 12 50 12 50 µA TA = 25˚C, (Note 2), V+ = 15V (Note 5) RS = 0Ω IIN(+) − IIN(−) RS = 0Ω 40 60 4 40 60 5 40 60 7 mA mV µV/˚C 7 15 30 7 20 75 7 100 10 40 0 300 V+−2 nA pA/˚C nA V 10 40 0 200 100 V+−2 0 10 40 300 200 V+−2 3 www.national.com LM158/LM258/LM358/LM2904 Electrical Characteristics Parameter Large Signal Voltage Gain Output Voltage Swing Output Current V+ = +15V (Continued) V+ = +5.0V, (Note 4), unless otherwise stated Conditions LM158A Min Typ 25 RL = 2 kΩ RL = 10 kΩ 26 27 28 5 10 10 20 15 20 10 5 Max LM358A Min Typ 15 26 27 28 5 20 8 20 10 5 Max LM158/LM258 Min Typ 25 26 27 28 5 20 8 20 Max V/mV V V mV mA mA Units (VO = 1V to 11V) RL ≥ 2 kΩ VOH V+ = +30V (LM2904, V+ = 26V) VOL V+ = 5V, RL = 10 kΩ Source VIN+ = +1V, VIN− = 0V, V+ = 15V, VO = 2V Sink VIN− = +1V, VIN+ = 0V, V+ = 15V, VO = 2V Electrical Characteristics V+ = +5.0V, (Note 4), unless otherwise stated Parameter Large Signal Voltage Gain Common-Mode Rejection Ratio Power Supply Rejection Ratio Amplifier-to-Amplifier Coupling Output Current Conditions V+ = 15V, TA = 25˚C, RL ≥ 2 kΩ, (For VO = 1V to 11V) TA = 25˚C, VCM = 0V to V+−1.5V V+ = 5V to 30V (LM2904, V+ = 5V to 26V), TA = 25˚C f = 1 kHz to 20 kHz, TA = 25˚C (Input Referred), (Note 8) Source VIN+ = 1V, VIN− = 0V, V+ = 15V, VO = 2V, TA = 25˚C Sink VIN− = 1V, VIN+ = 0V V+ = 15V, TA = 25˚C, VO = 2V VIN− = 1V, VIN+ = 0V TA = 25˚C, VO = 200 mV, V+ = 15V Short Circuit to Ground Input Offset Voltage Input Offset Voltage Drift Input Offset Current Input Offset Current Drift Input Bias Current Input Common-Mode Voltage Range IIN(+) or IIN(−) V+ = 30 V, (Note 7) (LM2904, V+ = 26V) 0 IIN(+) − IIN(−) RS = 0Ω 10 40 500 V+−2 0 TA = 25˚C, (Note 2), V+ = 15V (Note 5) RS = 0Ω 7 150 40 60 9 7 45 10 40 500 V+ −2 200 40 60 10 mA mV µV/˚C nA pA/˚C nA V 12 50 12 50 µA 10 20 10 20 mA 20 40 20 40 mA −120 −120 dB 65 100 50 100 dB 65 85 50 70 dB 25 100 25 100 V/mV LM358 Min Typ Max Min LM2904 Typ Max Units www.national.com 4 LM158/LM258/LM358/LM2904 Electrical Characteristics Parameter Large Signal Voltage Gain Output Voltage Swing Output Current V+ = +15V (Continued) V+ = +5.0V, (Note 4), unless otherwise stated Conditions LM358 Min 15 RL = 2 kΩ RL = 10 kΩ 26 27 28 5 10 5 20 8 20 10 5 Typ Max Min 15 22 23 24 5 20 8 100 LM2904 Typ Max V/mV V V mV mA mA Units (VO = 1V to 11V) RL ≥ 2 kΩ VOH V+ = +30V (LM2904, V+ = 26V) VOL V+ = 5V, RL = 10 kΩ Source VIN+ = +1V, VIN− = 0V, V+ = 15V, VO = 2V Sink VIN− = +1V, VIN+ = 0V, V+ = 15V, VO = 2V Note 1: For operating at high temperatures, the LM358/LM358A, LM2904 must be derated based on a +125˚C maximum junction temperature and a thermal resistance of 120˚C/W for MDIP, 182˚C/W for Metal Can, 189˚C/W for Small Outline package, and 230˚C/W for micro SMD, which applies for the device soldered in a printed circuit board, operating in a still air ambient. The LM258/LM258A and LM158/LM158A can be derated based on a +150˚C maximum junction temperature. The dissipation is the total of both amplifiers — use external resistors, where possible, to allow the amplifier to saturate or to reduce the power which is dissipated in the integrated circuit. Note 2: Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short cirucits to ground, the maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15V, continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers. Note 3: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to the V+voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3V (at 25˚C). Note 4: These specifications are limited to −55˚C ≤ TA ≤ +125˚C for the LM158/LM158A. With the LM258/LM258A, all temperature specifications are limited to −25˚C ≤ TA ≤ +85˚C, the LM358/LM358A temperature specifications are limited to 0˚C ≤ TA ≤ +70˚C, and the LM2904 specifications are limited to −40˚C ≤ TA ≤ +85˚C. Note 5: VO . 1.4V, RS = 0Ω with V+ from 5V to 30V; and over the full input common-mode range (0V to V+ −1.5V) at 25˚C. For LM2904, V+ from 5V to 26V. Note 6: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so no loading change exists on the input lines. Note 7: The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25˚C). The upper end of the common-mode voltage range is V+ −1.5V (at 25˚C), but either or both inputs can go to +32V without damage (+26V for LM2904), independent of the magnitude of V+. Note 8: Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be detected as this type of capacitance increases at higher frequencies. Note 9: Refer to RETS158AX for LM158A military specifications and to RETS158X for LM158 military specifications. Note 10: Human body model, 1.5 kΩ in series with 100 pF. 5 www.national.com LM158/LM258/LM358/LM2904 Typical Performance Characteristics Input Voltage Range Input Current 00778734 00778735 Supply Current Voltage Gain 00778736 00778737 Open Loop Frequency Response Common-Mode Rejection Ratio 00778738 00778739 www.national.com 6 LM158/LM258/LM358/LM2904 Typical Performance Characteristics Voltage Follower Pulse Response (Continued) Voltage Follower Pulse Response (Small Signal) 00778740 00778741 Large Signal Frequency Response Output Characteristics Current Sourcing 00778742 00778743 Output Characteristics Current Sinking Current Limiting 00778744 00778745 7 www.national.com LM158/LM258/LM358/LM2904 Typical Performance Characteristics Input Current (LM2902 only) (Continued) Voltage Gain (LM2902 only) 00778746 00778747 Application Hints The LM158 series are op amps which operate with only a single power supply voltage, have true-differential inputs, and remain in the linear mode with an input common-mode voltage of 0 VDC. These amplifiers operate over a wide range of power supply voltage with little change in performance characteristics. At 25˚C amplifier operation is possible down to a minimum supply voltage of 2.3 VDC. Precautions should be taken to insure that the power supply for the integrated circuit never becomes reversed in polarity or that the unit is not inadvertently installed backwards in a test socket as an unlimited current surge through the resulting forward diode within the IC could cause fusing of the internal conductors and result in a destroyed unit. Large differential input voltages can be easily accomodated and, as input differential voltage protection diodes are not needed, no large input currents result from large differential input voltages. The differential input voltage may be larger than V+ without damaging the device. Protection should be provided to prevent the input voltages from going negative more than −0.3 VDC (at 25˚C). An input clamp diode with a resistor to the IC input terminal can be used. To reduce the power supply current drain, the amplifiers have a class A output stage for small signal levels which converts to class B in a large signal mode. This allows the amplifiers to both source and sink large output currents. Therefore both NPN and PNP external current boost transistors can be used to extend the power capability of the basic amplifiers. The output voltage needs to raise approximately 1 diode drop above ground to bias the on-chip vertical PNP transistor for output current sinking applications. For ac applications, where the load is capacitively coupled to the output of the amplifier, a resistor should be used, from the output of the amplifier to ground to increase the class A bias current and prevent crossover distortion. Where the load is directly coupled, as in dc applications, there is no crossover distortion. Capacitive loads which are applied directly to the output of the amplifier reduce the loop stability margin. Values of 50 pF can be accomodated using the worst-case non-inverting unity gain connection. Large closed loop gains or resistive isolation should be used if larger load capacitance must be driven by the amplifier. The bias network of the LM158 establishes a drain current which is independent of the magnitude of the power supply voltage over the range of 3 VDC to 30 VDC. Output short circuits either to ground or to the positive power supply should be of short time duration. Units can be destroyed, not as a result of the short circuit current causing metal fusing, but rather due to the large increase in IC chip dissipation which will cause eventual failure due to excessive function temperatures. Putting direct short-circuits on more than one amplifier at a time will increase the total IC power dissipation to destructive levels, if not properly protected with external dissipation limiting resistors in series with the output leads of the amplifiers. The larger value of output source current which is available at 25˚C provides a larger output current capability at elevated temperatures (see typical performance characteristics) than a standard IC op amp. The circuits presented in the section on typical applications emphasize operation on only a single power supply voltage. If complementary power supplies are available, all of the standard op amp circuits can be used. In general, introducing a pseudo-ground (a bias voltage reference of V+/2) will allow operation above and below this value in single power supply systems. Many application circuits are shown which take advantage of the wide input common-mode voltage range which includes ground. In most cases, input biasing is not required and input voltages which range to ground can easily be accommodated. www.national.com 8 LM158/LM258/LM358/LM2904 Connection Diagrams DIP/SO Package Metal Can Package 00778701 00778702 Top View 8-Bump micro SMD Top View 00778755 Top View (Bump Side Down) LM358BP micro SMD Marking Orientation LM2904IBP micro SMD Marking Orientation 00778757 00778756 Top View LM358TP micro SMD Marking Orientation Top View LM2904ITP micro SMD Marking Orientation 00778758 00778759 Top View Top View 9 www.national.com LM158/LM258/LM358/LM2904 Ordering Information Package SO-8 Temperature Range −55˚C to 125˚C −25˚C to 85˚C 0˚C to 70˚C LM358AM LM358AMX LM358M LM358MX LM358AN LM358N LM158AJ/883(Note 11) LM158J/883(Note 11) LM158J LM158AJLQML(Note 12) LM158AJQMLV(Note 12) LM158AH/883(Note 11) LM158H/883(Note 11) LM158AH LM158H LM158AHLQML(Note 12) LM158AHLQMLV(Note 12) LM258H LM358H −40˚C to 85˚C LM2904M LM2904MX NSC Drawing M08A 8-Pin Molded DIP 8-Pin Ceramic DIP LM2904N N08E J08A TO-5, 8-Pin Metal Can H08C 8-Bump micro SMD 8-Bump micro SMD Lead Free 14-Pin Ceramic SOIC LM158AWG/883 LM358BP LM358BPX LM358TP LM358TPX LM2904IBP LM2904IBPX LM2904ITP LM2904ITPX BPA08AAB 0.85 mm Thick TPA08AAA 0.50 mm Thick WG10A Note 11: LM158 is available per SMD #5962-8771001 LM158A is available per SMD #5962-8771002 Note 12: See STD Mil DWG 5962L87710 for Radiation Tolerant Devices www.national.com 10 LM158/LM258/LM358/LM2904 Typical Single-Supply Applications (V+ = 5.0 VDC) Non-Inverting DC Gain (0V Output) 00778706 00778707 *R not needed due to temperature independent IIN DC Summing Amplifier (VIN’S ≥ 0 VDC and VO ≥ 0 VDC) Power Amplifier 00778709 00778708 Where: VO = V1 + V2 − V3 − V4 (V1 + V2) ≥ (V3 + V4) to keep VO > 0 VDC VO = 0 VDC for VIN = 0 VDC AV = 10 11 www.national.com LM158/LM258/LM358/LM2904 Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued) “BI-QUAD” RC Active Bandpass Filter 00778710 fo = 1 kHz Q = 50 Av = 100 (40 dB) Fixed Current Sources Lamp Driver 00778712 00778711 www.national.com 12 LM158/LM258/LM358/LM2904 Typical Single-Supply Applications (V+ LED Driver = 5.0 VDC) (Continued) Current Monitor 00778713 00778714 *(Increase R1 for IL small) VL ≤ V+ −2V Driving TTL Voltage Follower 00778715 00778717 VO = VIN Pulse Generator 00778716 13 www.national.com LM158/LM258/LM358/LM2904 Typical Single-Supply Applications (V+ Squarewave Oscillator = 5.0 VDC) (Continued) Pulse Generator 00778718 00778719 Low Drift Peak Detector 00778720 HIGH ZIN LOW ZOUT www.national.com 14 LM158/LM258/LM358/LM2904 Typical Single-Supply Applications (V+ High Compliance Current Sink = 5.0 VDC) (Continued) Comparator with Hysteresis 00778722 00778721 IO = 1 amp/volt VIN (Increase RE for IO small) Voltage Controlled Oscillator (VCO) 00778723 *WIDE CONTROL VOLTAGE RANGE: 0 VDC ≤ VC ≤ 2 (V+ −1.5V DC) 15 www.national.com LM158/LM258/LM358/LM2904 Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued) AC Coupled Inverting Amplifier 00778724 Ground Referencing a Differential Input Signal 00778725 www.national.com 16 LM158/LM258/LM358/LM2904 Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued) AC Coupled Non-Inverting Amplifier 00778726 Av = 11 (As Shown) DC Coupled Low-Pass RC Active Filter 00778727 fo = 1 kHz Q=1 AV = 2 17 www.national.com LM158/LM258/LM358/LM2904 Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued) Bandpass Active Filter 00778728 fo = 1 kHz Q = 25 High Input Z, DC Differential Amplifier 00778729 www.national.com 18 LM158/LM258/LM358/LM2904 Typical Single-Supply Applicati