SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely
voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.”
SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.
All rights reserved. Printed in U.S.A.
QUESTIONS REGARDING THIS DOCUMENT: (724) 772-7161 FAX: (724) 776-0243
TO PLACE A DOCUMENT ORDER: (724) 776-4970 FAX: (724) 776-0790
SAE WEB ADDRESS: http://www.sae.org
400 Commonwealth Drive, Warrendale, PA 15096-0001
AEROSPACE
MATERIAL
SPECIFICATION
AMS 2242F
Issued OCT 1945
Revised MAR 2001
Superseding AMS 2242E
Tolerances
Corrosion and Heat Resistant Steel, Iron Alloy,
Titanium, and Titanium Alloy Sheet, Strip, and Plate
1. SCOPE:
This specification covers established manufacturing tolerances applicable to sheet, strip, and plate of
corrosion and heat resistant steels, iron alloys, titanium, and titanium alloys ordered to inch
dimensions. These tolerances apply to all conditions, unless otherwise noted. The term “excl” is used
to apply only to the higher figure of the specified range.
1.1 MAM 2242 is the metric version of this AMS.
2. THICKNESS:
Thickness for sheet and strip is measured at any place on widths less than 1 inch, at any place 0.375
inch and over from an edge on widths 1 inch and over, and for plate at least 0.375 inch but not over 3
inches from an edge.
2.1 Sheet:
Table 1 includes crown tolerances.
Reaffirmed APR 2006
Copyright © 2006 SAE International
Copyright SAE International
Provided by IHS under license with SAE
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,```,,,,````-`-`,,`,,`,`,,`---
AMS 2242F SAE AMS 2242F
- 2 -
TABLE 1
Specified Thickness
Inch
Thickness Tolerance, Inch
Plus and Minus
For Width Ranges Shown
Inches
24 to 48,
incl
Thickness Tolerance, Inch
Plus and Minus
For Width Ranges Shown
Inches
Over 48
0.005 0.001 --
Over 0.005 to 0.007, incl 0.0015 --
Over 0.007 to 0.016, incl 0.002 --
Over 0.016 to 0.026, incl 0.003 0.003
Over 0.026 to 0.040, incl 0.004 0.004
Over 0.040 to 0.058, incl 0.004 0.005
Over 0.058 to 0.072, incl 0.005 0.006
Over 0.072 to 0.083, incl 0.005 0.007
Over 0.083 to 0.098, incl 0.006 0.008
Over 0.098 to 0.114, incl 0.007 0.009
Over 0.114 to 0.130, incl 0.008 0.010
Over 0.130 to 0.145, incl 0.010 0.012
Over 0.145 to 0.1875, excl 0.012 0.014
Copyright SAE International
Provided by IHS under license with SAE
Not for ResaleNo reproduction or networking permitted without license from IHS
-
-
`
,
,
`
`
`
,
,
,
,
`
`
`
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-
AMS 2242F SAE AMS 2242F
- 3 -
2.2 Strip:
Table 2 includes crown tolerances.
2.3 Plate:
Minus tolerances shall be 0.010 inch for all widths for all thicknesses up to 10.000 inches, inclusive,
in all alloys; plus tolerances shall be as in Table 3. For circles, the plus thickness tolerances in Table
3 apply to the diameter of the circle corresponding to the width ranges shown. For plates of irregular
shape, the plus thickness tolerances apply to the greatest width corresponding to the width ranges
shown.
TABLE 2
Specified Thickness
Inch
Thickness Tolerance
Inch
Plus and Minus
For Width Ranges Shown
Inches
3/16 to
6,
incl
Thickness Tolerance
Inch
Plus and Minus
For Width Ranges Shown
Inches
Over 6
to 12,
incl
Thickness Tolerance
Inch
Plus and Minus
For Width Ranges Shown
Inches
Over 12
to 24
excl
0.005 to 0.010, incl 0.10T 0.10T 0.10T
Over 0.010 to 0.011, incl 0.0015 0.0015 0.0015
Over 0.011 to 0.013, incl 0.0015 0.0015 0.002
Over 0.013 to 0.017, incl 0.0015 0.002 0.002
Over 0.017 to 0.020, incl 0.0015 0.002 0.0025
Over 0.020 to 0.029, incl 0.002 0.0025 0.0025
Over 0.029 to 0.035, incl 0.002 0.003 0.003
Over 0.035 to 0.050, incl 0.0025 0.0035 0.0035
Over 0.050 to 0.069, incl 0.003 0.0035 0.0035
Over 0.069 to 0.100, incl 0.003 0.004 0.005
Over 0.100 to 0.125, incl 0.004 0.0045 0.005
Over 0.125 to 0.161, incl 0.0045 0.0045 0.005
Over 0.161 to 0.1875, excl 0.005 0.005 0.006
Copyright SAE International
Provided by IHS under license with SAE
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,```,,,,````-`-`,,`,,`,`,,`---
AMS 2242F SAE AMS 2242F
- 4 -
3. WIDTH:
3.1 Sheet:
3.1.1 Stretcher Leveled, Resquared:
3.1.2 Not Resquared, Flat or in Coils:
TABLE 3
Specified Thickness
Inches
Thickness Tolerance,
Inch, Plus
For Width Ranges Shown
Inches
Over 10
to 84,
incl
Thickness Tolerance,
Inch, Plus
For Width Ranges Shown
Inches
Over 84
to 120,
incl
Thickness Tolerance,
Inch, Plus
For Width Ranges Shown
Inches
Over 120
to 144,
incl
Thickness Tolerance,
Inch, Plus
For Width Ranges Shown
Inches
Over 144
0.1875 to 0.375, excl 0.045 0.050 -- --
0.375 to 0.750, excl 0.055 0.060 0.075 0.090
0.750 to 1.000, excl 0.060 0.065 0.085 0.100
1.000 to 2.000, excl 0.070 0.075 0.095 0.115
2.000 to 3.000, excl 0.125 0.150 0.175 0.200
3.000 to 4.000, excl 0.175 0.210 0.245 0.280
4.000 to 6.000, excl 0.250 0.300 0.350 0.400
6.000 to 8.000, excl 0.350 0.420 0.490 0.560
8.000 to 10.000, incl 0.450 0.540 0.630 --
TABLE 4
Specified Thickness
Inch
Width Tolerance
Inch, Plus Only
For Width Ranges Shown
Inches
24 to 48,
excl
Width Tolerance
Inch, Plus Only
For Width Ranges Shown
Inches
48 and
Over
Up to 0.131, excl 1/16 1/8
0.131 to 0.150, incl 1/8 1/8
Over 0.150 to 0.170, incl 3/16 3/16
Over 0.170 to 0.1875, excl 1/4 1/4
TABLE 5
Specified Width
Inches
Width Tolerance, Inch
Plus Only
24 to 48, excl 1/16
48 and over 1/8
Copyright SAE International
Provided by IHS under license with SAE
Not for ResaleNo reproduction or networking permitted without license from IHS
-
-
`
,
,
`
`
`
,
,
,
,
`
`
`
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-
AMS 2242F SAE AMS 2242F
- 5 -
3.2 Strip:
3.2.1 Rolled Edge or Approximately Square Edge Produced by Rolling or Filing After Slitting:
3.2.2 Slit Edge:
3.3 Plate:
Minus tolerance shall be 1/4 inch for all widths and lengths in all thicknesses up to 1.000 inch,
inclusive; plus tolerances shall be as shown in Table 8.
TABLE 6
Specified Width
Inches
Specified Thickness
Inch
Width Tolerance, Inch
Plus and Minus
Up to 0.28125, incl Up to 0.0625, incl 0.005
Over 0.28125 to 0.750, incl Up to 0.09375, incl 0.005
Over 0.750 to 5.000, incl Up to 0.125, incl 0.005
Over 5.000 to 9.000, incl 0.008 to 0.125, incl 0.010
Over 9.000 to 20.000, incl 0.015 to 0.105, incl 0.010
Over 20.000 0.023 to 0.080, incl 0.015
TABLE 7
Specified Width
Inches
Width Tolerance, Inch
Plus and Minus
For Thickness
Ranges Shown
Inch
Up to
0.068,
incl
Width Tolerance, Inch
Plus and Minus
For Thickness
Ranges Shown
Inch
Over 0.068
to 0.099,
incl
Width Tolerance, Inch
Plus and Minus
For Thickness
Ranges Shown
Inch
Over 0.099
to 0.160,
incl
Width Tolerance, Inch
Plus and Minus
For Thickness
Ranges Shown
Inch
Over 0.160
to 0.1875,
excl
0.1875 to 0.500, incl 0.005 0.008 0.010 --
Over 0.500 to 6.000, incl 0.005 0.008 0.010 0.016
Over 6.000 to 9.000, incl 0.005 0.010 0.016 0.020
Over 9.000 to 12.000, incl 0.010 0.010 0.016 0.020
Over 12.000 to 20.000, incl 0.016 0.016 0.020 0.031
Over 20.000 to 24.000, incl 0.020 0.020 0.020 0.031
Copyright SAE International
Provided by IHS under license with SAE
Not for ResaleNo reproduction or networking permitted without license from IHS
-
-
`
,
,
`
`
`
,
,
,
,
`
`
`
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-
AMS 2242F SAE AMS 2242F
- 6 -
TABLE 8
Specified Width
Inches
Specified
Length
Inches
Width Tolerance, Inches
Plus
For Thickness Ranges Shown
Inch
3/16 to
3/8
excl
Width Tolerance, Inches
Plus
For Thickness Ranges Shown
Inch
3/8 to
1/2,
incl
Width Tolerance, Inches
Plus
For Thickness Ranges Shown
Inch
Over 1/2
to 1,
incl
Over 10 to 48, incl Up to
144
incl
1/8 3/16 5/16
Over 48 to 60, incl 3/16 1/4 3/8
Over 60 to 84, incl 1/4 5/16 7/16
Over 84 to 108, incl 5/16 3/8 1/2
Over 108 3/8 7/16 5/8
Over 10 to 48, incl Over
144 to
240
incl
3/16 1/4 5/16
Over 48 to 60, incl 1/4 5/16 3/8
Over 60 to 84, incl 3/8 7/16 1/2
Over 84 to 108, incl 7/16 1/2 5/8
Over 108 1/2 5/8 11/16
Over 10 to 48, incl Over
240 to
360
incl
1/4 5/16 3/8
Over 48 to 60, incl 5/16 3/8 1/2
Over 60 to 84, incl 7/16 1/2 5/8
Over 84 to 108, incl 9/16 5/8 3/4
Over 108 5/8 11/16 7/8
Over 10 to 60, incl Over
360
480,
incl
7/16 1/2 5/8
Over 60 to 84, incl 1/2 5/8 3/4
Over 84 to 108, incl 9/16 3/4 7/8
Over 108 3/4 7/8 1
Over 10 to 60, incl Over
480 to
600,
incl
7/16 1/2 5/8
Over 60 to 84, incl 1/2 5/8 3/4
Over 84 to 108, incl 5/8 3/4 7/8
Over 108 3/4 7/8 1
Over 10 to 60, incl Over
600
1/2 5/8 3/4
Over 60 to 108, incl 5/8 3/4 7/8
Over 108 7/8 1 1-1/8
Copyright SAE International
Provided by IHS under license with SAE
Not for ResaleNo reproduction or networking permitted without license from IHS
-
-
`
,
,
`
`
`
,
,
,
,
`
`
`
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-
AMS 2242F SAE AMS 2242F
- 7 -
4.1.1 Stretcher Leveled, Resquared:
4.1.2 Not Resquared:
4.2 Strip:
4.3 Plate:
Minus tolerances shall be 1/4 inch for all lengths and widths in all thicknesses up to 1 inch, inclusive;
plus tolerances shall be as shown in Table 12.
TABLE 9
Specified Thickness
Inch
Specified Length
Inches
Length Tolerance
Inch
Plus Only
Up to 0.131, incl Up to 120, excl 1/16
Up to 0.131, excl 120 and over 1/8
0.131 to 0.150, incl All 1/8
Over 0.150 to 0.170, incl All 3/16
Over 0.170 to 0.1875, excl All 1/4
TABLE 10
Specified Length
Inches
Length Tolerance,
Inch
Plus Only
Up to 120, incl 1/4
Over 120 to 240, incl 1/2
TABLE 11
Specified Length
Inches
Length Tolerance,
Inch
Plus Only
Up to 60, incl 3/8
Over 60 to 120, incl 1/2
Over 120 to 240, incl 5/8
4. LENGTH:
4.1 Sheet:
Copyright SAE International
Provided by IHS under license with SAE
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,```,,,,````-`-`,,`,,`,`,,`---
AMS 2242F SAE AMS 2242F
- 8 -
5. STRAIGHTNESS:
5.1 Sheet and Strip:
TABLE 12
Specified Width
Inches
Specified
Length
Inches
Length Tolerance, Inches
Plus
For Thickness Ranges Shown
Inch
3/16 to
3/8
excl
Length Tolerance, Inches
Plus
For Thickness Ranges Shown
Inch
3/8 to
1/2,
incl
Length Tolerance, Inches
Plus
For Thickness Ranges Shown
Inch
Over 1/2
to 1,
incl
Over 10 to 48, incl Up to
144,
incl
3/16 1/4 3/8
Over 48 to 60, incl 1/4 5/16 7/16
Over 60 to 84, incl 5/16 3/8 1/2
Over 84 to 108, incl 3/8 7/16 9/16
Over 108 7/16 1/2 11/16
Over 10 to 48, incl Over
144 to
240
incl
3/8 1/2 5/8
Over 48 to 60, incl 7/16 5/8 3/4
Over 60 to 84, incl 1/2 11/16 3/4
Over 84 to 108, incl 9/16 3/4 7/8
Over 108 5/8 7/8 1
Over 10 to 48, incl Over
240 to
360
incl
1/2 5/8 3/4
Over 48 to 60, incl 5/8 3/4 3/4
Over 60 to 84, incl 11/16 3/4 7/8
Over 84 to 108, incl 3/4 7/8 1
Over 108 7/8 1 1
Over 10 to 60, incl Over
360 to
480,
incl
1-1/8 1-1/4 1-3/8
Over 60 to 108, incl 1-1/4 1-3/8 1-1/2
Over 108 1-3/8 1-1/2 1-5/8
Over 10 to 60, incl Over
480 to
600,
incl
1-1/4 1-1/2 1-5/8
Over 60 to 108, incl 1-3/8 1-1/2 1-5/8
Over 108 1-1/2 1-5/8 1-3/4
Over 10 to 108, incl Over
600
1-3/4 1-7/8 1-7/8
Over 108 1-3/4 2 2-1/4
Copyright SAE International
Provided by IHS under license with SAE
Not for ResaleNo reproduction or networking permitted without license from IHS
-
-
`
,
,
`
`
`
,
,
,
,
`
`
`
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-
AMS 2242F SAE AMS 2242F
- 9 -
5.2 Plate:
Shall be of such straightness that the maximum edgewise curvature (depth of arc) shall not exceed
1/8 inch in any 5 ft of length.
6. FLATNESS:
The following tolerances do not apply to strip, dead soft sheet, or deep drawing sheet for which there
are no established tolerances. In all cases, the “Variation from Flat” is the maximum deviation from a
horizontal flat surface.
6.1 Sheet, Not Stretcher Leveled:
The following table does not apply to cold worked tempers of austenitic grades.
6.2 Cold Worked Austenitic Sheet, 1/4 and 1/2 Hard Tempers:
TABLE 13
Specified Width
Inches
Camber Tolerance, Inch,
in Any 8 ft of Length
Up to 1.500, incl 1/2
Over 1.500 to 24.000, excl 1/4
24.000 to 36.000, incl 1/8
Over 36.000 3/32
TABLE 14
Specified Thickness
Inch
Specified Width
Inches
Variation
from Flat,
Inch
Up to 0.062, excl 24 to 36, incl 1/2
Over 36 to 60, incl 3/4
Over 60 1
0.062 to 0.1875, excl 24 to 60, incl 1/2
Over 60 to 72, incl 3/4
Over 72 1
Copyright SAE International
Provided by IHS under license with SAE
Not for ResaleNo reproduction or networking permitted without license from IHS
-
-
`
,
,
`
`
`
,
,
,
,
`
`
`
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-
AMS 2242F SAE AMS 2242F
- 10 -
6.3 Sheet, Stretcher Leveled:
6.4 Plate:
The requirements of Table 17 apply to plate up to 15 feet, inclusive, in length, or to any 15 feet of
longer plates. If the longer dimension is under 3 feet, the variation from flat shall be not greater than
1/4 inch in any direction.
6.4.1 Titanium plate, when specified to have “Special Flatness”, shall be creep flattened in a stress-free
condition with deviation from flat not exceeding 0.060 inch in any 12 inches, with total deviation not
exceeding 0.125 inch.
TABLE 15
Specified Thickness
Inch
Specified Width
Inches
Variation
from Flat
Inches
1/4 Hard
Variation
from Flat
Inches
1/2 Hard
Up to 0.016, incl 24 to 36,
excl
1/2 3/4
Over 0.016 to 0.030, incl 5/8 7/8
Over 0.030 to 0.1875, excl 3/4 7/8
Up to 0.016, incl 36 to 48
incl
5/8 1
Over 0.016 to 0.030, incl 3/4 1-1/8
Over 0.030 to 0.1875, excl 1 1-1/8
TABLE 16
Specified Width
Inches
Specified Length
Inches
Variation
From Flat,
Inch
24 to 48, incl Up to 96, incl 1/8
Over 96 1/4
Over 48 All 1/4
Copyright SAE International
Provided by IHS under license with SAE
Not for ResaleNo reproduction or networking permitted without license from IHS
-
-
`
,
,
`
`
`
,
,
,
,
`
`
`
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-
A
M
S
2242F
SA
E
A
M
S
2242F
-
11
-
TABLE 17
Specified Thickness
Inches
Variation from
Flat Inches
For Width
Ranges Shown
Inches
Up to
48,
incl
Variation from
Flat Inches
For Width
Ranges Shown
Inches
Over 48
to 60,
excl
Variation from
Flat Inches
For Width
Ranges Shown
Inches
60 to
72,
excl
Variation from
Flat Inches
For Width
Ranges Shown
Inches
72 to
84,
excl
Variation from
Flat Inches
For Width
Ranges Shown
Inches
84 to
96,
excl
Variation from
Flat Inches
For Width
Ranges Shown
Inches
96 to
108,
excl
Variation from
Flat Inches
For Width
Ranges Shown
Inches
108 to
120,
excl
Variation from
Flat Inches
For Width
Ranges Shown
Inches
120 to
144,
excl
Variation from
Flat Inches
For Width
Ranges Shown
Inches
144
and
over
0.1875 to 0.250, excl 3/4 1-1/16 1-1/4 1-3/8 1-5/8 1-5/8 1-7/8 2 --
0.250 to 0.375, excl 11/16 3/4 15/16 1-1/8 1-3/8 1-7/16 1-9/16 1-7/8 --
0.375 to 0.500, excl 1/2 9/16 11/16 3/4 15/16 1-1/8 1-1/4 1-7/16 1-3/4
0.500 to 0.750, excl 1/2 9/16 5/8 5/8 13/16 1-1/8 1-1/8 1-1/8 1-3/8
0.750 to 1.000, excl 1/2 9/16 5/8 5/8 3/4 13/16 15/16 1 1-1/8
1.000 to 1.500, excl 1/2 9/16 9/16 9/16 11/16 11/16 11/16 3/4 1
1.500 to 4.000, excl 3/16 5/16 3/8 7/16 1/2 9/16 5/8 3/4 7/8
4.000 to 6.000, excl 1/4 3/8 1/2 9/16 5/8 3/4 7/8 1 1-1/8
Copyright SAE International
Provided by IHS under license with SAE
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,```,,,,````-`-`,,`,,`,`,,`---
专业技术
标准
excel标准偏差excel标准偏差函数exl标准差函数国标检验抽样标准表免费下载红头文件格式标准下载
翻译,加QQ:2298175560
AMS 2242F SAE AMS 2242F
- 12 -
7. NOTES:
7.1 A change bar ( l ) located in the left margin is for the convenience of the user in locating areas where
technical revisions, not editorial changes, have been made to the previous issue of this specification.
An (R) symbol to the left of the document title indicates a complete revision of the specification,
including technical revisions. Change bars and (R) are not used in original publications, nor in
specifications that contain editorial changes only.
PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “F”
Copyright SAE International
Provided by IHS under license with SAE
Not for ResaleNo reproduction or networking permitted without license from IHS
-
-
`
,
,
`
`
`
,
,
,
,
`
`
`
`
-
`
-
`
,
,
`
,
,
`
,
`
,
,
`
-
-
-