光耦A3150

TRUTH TABLE VCC - VEE VCC - VEE “Positive Going” “Negative-Going” LED (i.e., Turn-On) (i.e., Turn-Off) VO OFF 0 - 30 V 0 - 30 V LOW ON 0 - 11 V 0 - 9.5 V LOW ON 11 - 13.5 V 9.5 - 12 V TRANSITION ON 13.5 - 30 V 12 - 30 V HIGH 0.5 Amp Output Current IGBT Gate Drive Optocoupler Technical Data HCPL-3150 (Single Channel) HCPL-315J (Dual Channel) Features • 0.5 A Minimum Peak Output Current • 15 kV/µs Minimum Common Mode Rejection (CMR) at VCM = 1500 V • 1.0 V Maximum Low Level Output Voltage (VOL) Eliminates Need for Negative Gate Drive • ICC = 5 mA Maximum Supply Current • Under Voltage Lock-Out Protection (UVLO) with Hysteresis • Wide Operating VCC Range: 15 to 30 Volts • 0.5 µs Maximum Propagation Delay • +/– 0.35 µs Maximum Delay Between Devices/Channels • Industrial Temperature Range: -40°C to 100°C • HCPL-315J: Channel One to Channel Two Output Isolation = 1500 Vrms/1 min. • Safety and Regulatory Approval: UL Recognized (UL1577) 3750 Vrms/1 min. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. IEC/EN/DIN EN 60747-5-2 Approved VIORM = 630 Vpeak (HCPL-3150 Option 060 only) VIORM = 891 Vpeak (HCPL- 315J) CSA Certified Applications • Isolated IGBT/MOSFET Gate Drive • AC and Brushless DC Motor Drives • Industrial Inverters • Switch Mode Power Supplies (SMPS) • Uninterruptable Power Supplies (UPS) Description The HCPL-315X consists of a LED optically coupled to an integrated circuit with a power output stage. This optocoupler is ideally suited for driving power IGBTs and MOSFETs used in motor control inverter applica- tions. The high operating voltage range of the output stage pro- vides the drive voltages required by gate controlled devices. The voltage and current supplied by this optocoupler makes it ideally suited for directly driving IGBTs with ratings up to 1200 V/50 A. For IGBTs with higher ratings, the HCPL-3150/315J can be used to drive a discrete power stage which drives the IGBT gate. A 0.1 µF bypass capacitor must be connected between the VCC and VEE pins for each channel. Functional Diagram 1 3 SHIELD 2 4 8 6 7 5 N/C CATHODE ANODE N/C VCC VO VO VEE HCPL-3150 1 3 SHIELD 2 8 16 14 15 9 N/C CATHODE ANODE N/C VCC VEE VO VEE 7 6 10 11 CATHODE ANODE VO VCC SHIELD HCPL-315J 2 Ordering Information Specify Part Number followed by Option Number (if desired) Example HCPL-315Y#XXXX No Option = Standard DIP package, 50 per tube. 060 = IEC/EN/DIN EN 60747-5-2 VIORM = 630 Vpeak Option, 50 per tube. (HCPL-3150 only) 300 = Gull Wing Surface Mount Option, 50 per tube. (HCPL-3150 only) 500 = Tape and Reel Packaging Option. HCPL-3150; 1000 per reel. HCPL-315J; 850 per reel. XXXE = Lead Free Option ∅ = Single Channel, 8-pin PDIP. J = Dual Channel, SO16. Option data sheets available. Contact Agilent sales representative or authorized distributor. Remarks: The notation “#” is used for existing products, while (new) products launched since 15th July 2001 and lead free option will use “–” Package Outline Drawings Standard DIP Package Selection Guide: Invertor Gate Drive Optoisolators Widebody Package Type 8-Pin DIP (300 mil) (400 mil) Small Outline SO-16 Part Number HCPL-3150 HCPL-3120 HCPL-J312 HCPL-J314 HCNW-3120 HCPL-315J HCPL-316J HCPL-314J Number of 1 1 1 1 1 2 1 2 Channels IEC/EN/DIN EN VIORM VIORM VIORM VIORM 60747-5-2 630 Vpeak 891Vpeak 1414 Vpeak 891 Vpeak Approvals Option 060 UL 3750 3750 5000 3750 Approval Vrms/1 min. Vrms/1 min. Vrms/1min. Vrms/1 min. Output Peak 0.5A 2A 2A 0.4A 2A 0.5A 2A 0.4A Current CMR 15 kV/µs 10 kV/µs 15 kV/µs 10 kV/µs (minimum) UVLO Yes No Yes No Fault Status No Yes No 9.40 (0.370) 9.90 (0.390) PIN ONE 1.78 (0.070) MAX.1.19 (0.047) MAX. A 3150 Z YYWW DATE CODE 0.76 (0.030) 1.40 (0.055) 2.28 (0.090) 2.80 (0.110) 0.51 (0.020) MIN. 0.65 (0.025) MAX. 4.70 (0.185) MAX. 2.92 (0.115) MIN. 6.10 (0.240) 6.60 (0.260) 0.20 (0.008) 0.33 (0.013) 5° TYP. 7.36 (0.290) 7.88 (0.310) 1 2 3 4 8 7 6 5 5678 4321 GND1 VDD1 VIN+ VIN– GND2 VDD2 VOUT+ VOUT– PIN DIAGRAM PIN ONE DIMENSIONS IN MILLIMETERS AND (INCHES). * MARKING CODE LETTER FOR OPTION NUMBERS. "V" = OPTION 060. OPTION NUMBERS 300 AND 500 NOT MARKED. OPTION CODE* NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 3 Package Outline Drawings Gull-Wing Surface-Mount Option 300 16 - Lead Surface Mount 0.635 ± 0.25 (0.025 ± 0.010) 12° NOM. 0.20 (0.008) 0.33 (0.013) 9.65 ± 0.25 (0.380 ± 0.010) 0.635 ± 0.130 (0.025 ± 0.005) 7.62 ± 0.25 (0.300 ± 0.010) 5678 4321 9.65 ± 0.25 (0.380 ± 0.010) 6.350 ± 0.25 (0.250 ± 0.010) MOLDED 1.080 ± 0.320 (0.043 ± 0.013) 1.780 (0.070) MAX.1.19 (0.047) MAX. 2.540 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). TOLERANCES (UNLESS OTHERWISE SPECIFIED): LEAD COPLANARITY MAXIMUM: 0.102 (0.004) xx.xx = 0.01 xx.xxx = 0.005 A 3150 Z YYWW *MARKING CODE LETTER FOR OPTION NUMBERS. "V" = OPTION 060. OPTION NUMBERS 300 AND 500 NOT MARKED. OPTION CODE* 1.016 (0.040) 1.27 (0.050) 10.9 (0.430) 2.0 (0.080) LAND PATTERN RECOMMENDATION 3.56 ± 0.13 (0.140 ± 0.005) NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. HCPL-315J10.36 ± 0.20(0.408 ± 0.008) (0.295 ± 0.004) 7.49 ± 0.10 (0.406 ± 0.007) 10.31 ± 0.18 (0.138 ± 0.005) 3.51 ± 0.13 (0.018) 0.457 (0.050) 1.27 9° 16 15 14 11 10 9 1 2 3 6 7 8 VIEW FROM PIN 16 VIEW FROM PIN 1 (0.025 MIN.) 0.64 (0.408 ± 0.008) 10.36 ± 0.20 (0.0091 – 0.0125) 0.23 – 0.32 (0.345 ± 0.008) 8.76 ± 0.20 ALL LEADS TO BE COPLANAR ± (0.002 INCHES) 0.05 mm. DIMENSIONS IN (INCHES) AND MILLIMETERS. 0 - 8° V C C1 V O 1 G ND 1 V C C2 V O 2 G ND 2 N C V I N 1 V 1 V I N 2 V 2 N C (0.004 – 0.011) 0.10 – 0.30 STANDOFF NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. (0.458) 11.63 (0.085) 2.16 (0.025) 0.64 LAND PATTERN RECOMMENDATION 4 Regulatory Information The HCPL-3150 and HCPL-315J have been approved by the following organizations: UL Recognized under UL 1577, Component Recognition Program, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. IEC/EN/DIN EN 60747-5-2 Approved under: IEC 60747-5-2:1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01. (Option 060 and HCPL-315J only) Solder Reflow Thermal Profile 0 TIME (SECONDS) TE M PE R A TU RE (° C) 200 100 50 150100 200 250 300 0 30 SEC. 50 SEC. 30 SEC. 160°C 140°C 150°C PEAK TEMP. 245°C PEAK TEMP. 240°C PEAK TEMP. 230°C SOLDERING TIME 200°C PREHEATING TIME 150°C, 90 + 30 SEC. 2.5°C ± 0.5°C/SEC. 3°C + 1°C/–0.5°C TIGHT TYPICAL LOOSEROOMTEMPERATURE PREHEATING RATE 3°C + 1°C/–0.5°C/SEC. REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. Recommended Pb-Free IR Profile 217 °C RAMP-DOWN 6 °C/SEC. MAX. RAMP-UP 3 °C/SEC. MAX. 150 - 200 °C 260 +0/-5 °C t 25 °C to PEAK 60 to 150 SEC. 20-40 SEC. TIME WITHIN 5 °C of ACTUAL PEAK TEMPERATURE tp ts PREHEAT 60 to 180 SEC. tL TL Tsmax Tsmin 25 Tp TIME TE M PE R AT UR E NOTES: THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX. Tsmax = 200 °C, Tsmin = 150 °C 5 IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Description Symbol HCPL-3150#060 HCPL-315J** Unit Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 150 Vrms I-IV for rated mains voltage ≤ 300 Vrms I-IV I-III for rated mains voltage ≤ 600 Vrms I-III I-II Climatic Classification 55/100/21 55/100/21 Pollution Degree (DIN VDE 0110/1.89) 2 2 Maximum Working Insulation Voltage VIORM 630 891 Vpeak Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 1181 1670 Vpeak Partial discharge < 5 pC Input to Output Test Voltage, Method a* VIORM x 1.5 = VPR, Type and Sample Test, tm = 60 sec, VPR 945 1336 Vpeak Partial discharge < 5 pC Highest Allowable Overvoltage* VIOTM 6000 6000 Vpeak (Transient Overvoltage tini = 10 sec) Safety-Limiting Values – Maximum Values Allowed in the Event of a Failure, Also See Figure 37, Thermal Derating Curve. Case Temperature TS 175 175 °C Input Current IS, INPUT 230 400 mA Output Power PS, OUTPUT 600 1200 mW Insulation Resistance at TS, VIO = 500 V RS ≥ 109 ≥ 109 Ω **Approval Pending. *Refer to the front of the optocoupler section of the current Catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a detailed description of Method a and Method b partial discharge test profiles. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. 6 Recommended Operating Conditions Parameter Symbol Min. Max. Units Power Supply Voltage (VCC - VEE) 15 30 Volts Input Current (ON) IF(ON) 7 16 mA Input Voltage (OFF) VF(OFF) -3.0 0.8 V Operating Temperature TA -40 100 °C Absolute Maximum Ratings Parameter Symbol Min. Max. Units Note Storage Temperature TS -55 125 °C Operating Temperature TA -40 100 °C Average Input Current IF(AVG) 25 mA 1, 16 Peak Transient Input Current IF(TRAN) 1.0 A (<1 µs pulse width, 300 pps) Reverse Input Voltage VR 5 Volts “High” Peak Output Current IOH(PEAK) 0.6 A 2, 16 “Low” Peak Output Current IOL(PEAK) 0.6 A 2, 16 Supply Voltage (VCC - VEE) 0 35 Volts Output Voltage VO(PEAK) 0 VCC Volts Output Power Dissipation PO 250 mW 3, 16 Total Power Dissipation PT 295 mW 4, 16 Lead Solder Temperature 260°C for 10 sec., 1.6 mm below seating plane Solder Reflow Temperature Profile See Package Outline Drawings Section Insulation and Safety Related Specifications Parameter Symbol HCPL-3150 HCPL-315J Units Conditions Minimum External L(101) 7.1 8.3 mm Measured from input terminals Air Gap to output terminals, shortest (External Clearance) distance through air. Minimum External L(102) 7.4 8.3 mm Measured from input terminals Tracking to output erminals, shortest (External Creepage) distance path along body. Minimum Internal 0.08 ≥ 0.5 mm Through insulation distance Plastic Gap conductor to conductor. (Internal Clearance) Tracking Resistance CTI ≥ 175 ≥ 175 Volts DIN IEC 112/VDE 0303 Part 1 (Comparative Tracking Index) Isolation Group IIIa IIIa Material Group (DIN VDE 0110, 1/89, Table 1) Option 300 - surface mount classification is Class A in accordance wtih CECC 00802. 7 Electrical Specifications (DC) Over recommended operating conditions (TA = -40 to 100°C, IF(ON) = 7 to 16 mA, VF(OFF) = -3.0 to 0.8 V, VCC = 15 to 30 V, VEE = Ground, each channel) unless otherwise specified. Parameter Symbol Min. Typ.* Max. Units Test Conditions Fig. Note High Level IOH 0.1 0.4 A VO = (VCC - 4 V) 2, 3, 5 0.5 VO = (VCC - 15 V) 2 Low Level IOL 0.1 0.6 A VO = (VEE + 2.5 V) 5, 6, 5 0.5 VO = (VEE + 15 V) 2 High Level Output VOH (VCC - 4) (VCC - 3) V IO = -100 mA 1, 3, 6, 7 Voltage 19 Low Level Output VOL 0.4 1.0 V IO = 100 mA 4, 6, Voltage 20 High Level ICCH 2.5 5.0 mA Output Open, 7, 8 16 Supply Current IF = 7 to 16 mA Low Level ICCL 2.7 5.0 mA Output Open, Supply Current VF = -3.0 to +0.8 V Threshold Input IFLH 2.2 5.0 mA HCPL-3150 IO = 0 mA, 9, 15, Current Low to High 2.6 6.4 HCPL-315J VO > 5 V 21 Threshold Input VFHL 0.8 V Voltage High to Low Input Forward Voltage VF 1.2 1.5 1.8 V HCPL-3150 IF = 10 mA 16 1.6 1.95 HCPL-315J Temperature ∆VF/∆TA -1.6 mV/°C IF = 10 mA Coefficient of Forward Voltage Input Reverse BVR 5 V HCPL-3150 IR = 10 µA Breakdown Voltage 3 HCPL-315J IR = 10 µA Input Capacitance CIN 70 pF f = 1 MHz, VF = 0 V UVLO Threshold VUVLO+ 11.0 12.3 13.5 V VO > 5 V, 22, VUVLO- 9.5 10.7 12.0 IF = 10 mA 36 UVLO Hysteresis UVLOHYS 1.6 V *All typical values at TA = 25°C and VCC - VEE = 30 V, unless otherwise noted. Output Current 17 18 Output Current 8 Switching Specifications (AC) Over recommended operating conditions (TA = -40 to 100°C, IF(ON) = 7 to 16 mA, VF(OFF) = -3.0 to 0.8 V, VCC = 15 to 30 V, VEE = Ground, each channel) unless otherwise specified. Parameter Symbol Min. Typ.* Max. Units Test Conditions Fig. Note Propagation Delay tPLH 0.10 0.30 0.50 µs Rg = 47 Ω, 10, 11, 14 Time to High Cg = 3 nF, 12, 13, Output Level f = 10 kHz, 14, 23 Duty Cycle = 50% Propagation Delay tPHL 0.10 0.3 0.50 µs Time to Low Output Level Pulse Width PWD 0.3 µs 15 Distortion Propagation Delay PDD -0.35 0.35 µs 34,35 10 Difference Between (tPHL - tPLH) Any Two Parts or Channels Rise Time tr 0.1 µs 23 Fall Time tf 0.1 µs UVLO Turn On tUVLO ON 0.8 µs VO > 5 V, 22 Delay IF = 10 mA UVLO Turn Off tUVLO OFF 0.6 µs VO < 5 V, Delay IF = 10 mA Output High Level |CMH| 15 30 kV/µs TA = 25°C, 24 11, 12 Common Mode IF = 10 to 16 mA, Transient VCM = 1500 V, Immunity VCC = 30 V Output Low Level |CML| 15 30 kV/µs TA = 25°C, 11, 13 Common Mode VCM = 1500 V, Transient VF = 0 V, Immunity VCC = 30 V 9 Notes: 1. Derate linearly above 70°C free-air temperature at a rate of 0.3 mA/°C. 2. Maximum pulse width = 10 µs, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with IO peak minimum = 0.5 A. See Applications section for additional details on limiting IOH peak. 3. Derate linearly above 70°C free-air temperature at a rate of 4.8 mW/°C. 4. Derate linearly above 70°C free-air temperature at a rate of 5.4 mW/°C. The maximum LED junction tempera- ture should not exceed 125°C. 5. Maximum pulse width = 50 µs, maximum duty cycle = 0.5%. 6. In this test VOH is measured with a dc load current. When driving capacitive loads VOH will approach VCC as IOH approaches zero amps. 7. Maximum pulse width = 1 ms, maximum duty cycle = 20%. 8. In accordance with UL1577, each HCPL-3150 optocoupler is proof tested by applying an insulation test voltage ≥ 4500 Vrms (≥ 5000 Vrms for the HCPL-315J) for 1 second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% production test for partial discharge (method b) shown in the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable. 9. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together. 10. The difference between tPHL and tPLH between any two parts or channels under the same test condition. 11. Pins 1 and 4 (HCPL-3150) and pins 3 and 4 (HCPL-315J) need to be connected to LED common. 12. Common mode transient immunity in the high state is the maximum tolerable |dVCM/dt| of the common mode pulse, VCM, to assure that the output will remain in the high state (i.e., VO > 15.0 V). 13. Common mode transient immunity in a low state is the maximum tolerable |dVCM/dt| of the common mode pulse, VCM, to assure that the output will remain in a low state (i.e., VO < 1.0 V). 14. This load condition approximates the gate load of a 1200 V/25 A IGBT. 15. Pulse Width Distortion (PWD) is defined as |tPHL-tPLH| for any given device. 16. Each channel. 17. Device considered a two terminal device: Channel one output side pins shorted together, and channel two output side pins shorted together. 18. See the thermal model for the HCPL-315J in the application section of this data sheet. Package Characteristics (each channel, unless otherwise specified) Parameter Symbol Device Min. Typ.* Max. Units Test Conditions Fig. Note Input-Output VISO HCPL-3150 3750 Vrms RH < 50%, 8, 9 Momentary t = 1 min., Withstand Voltage** HCPL-315J 3750 TA = 25°C Output-Output VO-O HCPL-315J 1500 Vrms RH < 50% 17 Momentary t = 1 min., Withstand Voltage** TA = 25°C Resistance RI-O 1012 Ω VI-O = 500 VDC 9 (Input - Output) Capacitance CI-O HCPL-3150 0.6 pF f = 1 MHz (Input - Output) HCPL-315J 1.3 LED-to-Case θLC HCPL-3150 391 °C/W Thermocouple 28 18 Thermal Resistance LED-to-Detector θLD HCPL-3150 439 °C/W Thermal Resistance Detector-to-Case θDC HCPL-3150 119 °C/W Thermal Resistance *All typical values at TA = 25°C and VCC - VEE = 30 V, unless otherwise noted. **The Input-Output/Output-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input- output/output-output continuous voltage rating. For the continuous voltage rating refer to your equipment level safety specification or Agilent Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage.” located at center underside of package 10 Figure 4. VOL vs. Temperature. Figure 5. IOL vs. Temperature. Figure 6. VOL vs. IOL. I O L – O UT PU T LO W C UR RE NT – A -40 0 TA – TEMPERATURE – °C 100 0.8 0.4 -20 1.0 0 20 40 0.2 60 80 VF(OFF) = -3.0 to 0.8 V VOUT = 2.5 V VCC = 15 to 30 V VEE = 0 V 0.6 V O L – O UT PU T LO W V O LT AG E – V -40 0 TA – TEMPERATURE – °C 100 0.8 0.6 -20 1.0 0 20 40 0.2 60 80 VF(OFF) = -3.0 to 0.8 V IOUT = 100 mA VCC = 15 to 30 V VEE = 0 V 0.4 V O L – O UT PU T LO W V O LT AG E – V 0 0 IOL – OUTPUT LOW CURRENT – A 1.0 4 0.2 5 0.4 0.6 1 0.8 VF(OFF) = -3.0 to 0.8 V VCC = 15 to 30 V VEE = 0 V 2 100 °C 25 °C -40 °C 3 Figure 1. VOH vs. Temperature. Figure 2. IOH vs. Temperature. Figure 3. VOH vs. IOH. (V O H - V C C ) – H IG H O UT PU T VO LT AG E DR O P – V -40 -4 TA – TEMPERATURE – °C 100 -1 -2 -20 0 0 20 40 -3 60 80 IF = 7 to 16 mA IOUT = -100 mA VCC = 15 to 30 V VEE = 0 V I O H – O UT PU T HI G H CU RR EN T – A -40 0.25 TA – TEMPERATURE – °C 100 0.45 0.40 -20 0.50 0 20 40 0.30 60 80 IF = 7 to 16 mA VOUT = VCC - 4 V VCC = 15 to 30 V VEE = 0 V 0.35 (V O H - V C C ) – O UT PU T HI G H VO LT AG E DR O P – V 0 -6 IOH – OUTPUT HIGH CURRENT – A 1.0 -2 -3 0.2 -1 0.4 0.6 -5 0.8 IF = 7 to 16 mA VCC = 15 to 30 V VEE = 0 V -4 100 °C 25 °C -40 °C I C C – SU PP LY C UR RE NT – m A -40 1.5 TA – TEMPERATURE – °C 100 3.0 2.5 -20 3.5 0 20 40 2.0 60 80 VCC = 30 V VEE = 0 V IF = 10 mA for ICCH IF = 0 mA for ICCL ICCH ICCL I C C – SU PP LY C UR RE NT – m A 15 1.5 VCC – SUPPLY VOLTAGE – V 30 3.0 2.5 3.5 20 2.0 25 IF = 10 mA for ICCH IF = 0 mA for ICCL TA = 25 °C VEE = 0 V ICCH ICCL I F LH – LO W T O H IG H CU RR EN T TH RE SH O LD – m A -40 0 TA – TEMPERATURE – °C 100 3 2 -20 4 0 20 40 1 60 80 5 VCC = 15 TO 30 V VEE = 0 V OUTPUT = OPEN Figure 7. ICC vs. Temperature. Figure 8. ICC vs. VCC. Figure 9. IFLH vs. Temperature. 11 Figure 16. Input Current vs. Forward Voltage. I F – FO RW AR D CU RR EN T – m A 1.10 0.001 VF – FORWARD VOLTAGE – V 1.60 10 1.0 0.1 1.20 1000 1.30 1.40 1.50 TA = 25°C IF VF + – 0.01 100 V O – O UT PU T VO LT AG E – V 0 0 IF – FORWARD LED CURRENT – mA 5 25 15 1 30 2 5 3 4 20 10 Figure 15. Transfer Characteristics.Figure 14. Propagation Delay vs. Cg.Figure 13. Propagation Delay vs. Rg. Figure 10. Propagation Delay vs. VCC. Figure 11. Propagation Delay vs. IF. Figure 12. Propagation Delay vs. Temperature. T p – PR O PA G AT IO N DE LA Y – n s 15 100 VCC – SUPPLY VOLTAGE – V 30 400 300 500 20 200 25 IF = 10 mA TA = 25 °C Rg = 47 Ω Cg = 3 nF DUTY CYCLE = 50% f = 10 kHz TPLH TPHL T p – PR O PA G AT IO N DE LA Y – n s 6 100 IF – FORWARD LED CURRENT – mA 16 400 300 500 10 200 12 VCC = 30 V, VEE = 0 V Rg = 47 Ω, Cg = 3 nF TA = 25 °C DUTY CYCLE = 50% f = 10 kHz TPLH TPHL 148 T p – PR O PA G AT IO N DE LA Y – n s -40 100 TA – TEMPERATURE – °C 100 400 300 -20 500 0 20 40 200 60 80 TPLH TPHL IF(ON) = 10 mA IF(OFF) = 0 mA VCC = 30 V, VEE = 0 V Rg = 47 Ω, Cg = 3 nF DUTY CYCLE = 50% f = 10 kHz T p – PR O PA G AT IO N DE LA Y – n s 0 100 Rg – SERIES LOAD RESISTANCE – Ω 200 400 300 50 500 100 200 150 TPLH TPHL VCC = 30 V, VEE = 0 V TA = 25 °C IF = 10 mA Cg = 3 nF DUTY CYCLE = 50% f = 10 kHz T p – PR O PA G AT IO N DE LA