h3c交换机配置命令
H3C交换机102条命令使用方法
1. switch(config)# hostname hostname
在基于CLI的交换机上设置主机名/系统名:
switch(enable) set system name name-string 2.在基于IOS的交换机上设置登录口令:
switch(config)# enable password level 1 password 在基于CLI的交换机上设置登录口令:
switch(enable) set password
switch(enable) set enalbepass
3.在基于IOS的交换机上设置远程访问:
switch(config)# interface vlan 1
switch(config-if)# ip address ip-address netmask switch(config-if)# ip default-gateway ip-address 在基于CLI的交换机上设置远程访问:
switch(enable) set interface sc0 ip-address netmask broadcast-address
switch(enable) set interface sc0 vlan
switch(enable) set ip route default gateway 4.在基于IOS的交换机上启用和浏览CDP信息:
switch(config-if)# cdp enable
switch(config-if)# no cdp enable
为了查看Cisco邻接设备的CDP通告信息:
switch# show cdp interface [type modle/port] switch# show cdp neighbors [type module/port] [detail] 在基于CLI的交换机上启用和浏览CDP信息:
switch(enable) set cdp {enable|disable} module/port 为了查看Cisco邻接设备的CDP通告信息:
switch(enable) show cdp neighbors[module/port] [vlan|duplex|capabilities|detail]
5.基于IOS的交换机的端口描述:
switch(config-if)# description description-string 基于CLI的交换机的端口描述:
switch(enable)set port name module/number description-string 6.在基于IOS的交换机上设置端口速度:
switch(config-if)# speed{10|100|auto}
在基于CLI的交换机上设置端口速度:
switch(enable) set port speed moudle/number {10|100|auto} switch(enable) set port speed moudle/number {4|16|auto} 7.在基于IOS的交换机上设置以太网的链路模式:
if)# duplex {auto|full|half} switch(config-
在基于CLI的交换机上设置以太网的链路模式:
switch(enable) set port duplex module/number {full|half} 8.在基于IOS的交换机上配置静态VLAN:
switch# vlan database
switch(vlan)# vlan vlan-num name vla
switch(vlan)# exit
switch# configure teriminal
switch(config)# interface interface module/number switch(config-if)# switchport mode access
switch(config-if)# switchport access vlan vlan-num switch(config-if)# end
在基于CLI的交换机上配置静态VLAN:
switch(enable) set vlan vlan-num [name name]
switch(enable) set vlan vlan-num mod-num/port-list 9. 在基于IOS的交换机上配置VLAN中继线:
switch(config)# interface interface mod/port
switch(config-if)# switchport mode trunk
switch(config-if)# switchport trunk encapsulation {isl|dotlq} switch(config-if)# switchport trunk allowed vlan remove vlan-list switch(config-if)# switchport trunk allowed vlan add vlan-list
在基于CLI的交换机上配置VLAN中继线:
switch(enable) set trunk module/port [on|off|desirable|auto|nonegotiate]
Vlan-range [isl|dotlq|dotl0|lane|negotiate] 10.在基于IOS的交换机上配置VTP管理域:
switch# vlan database
switch(vlan)# vtp domain domain-name 在基于CLI的交换机上配置VTP管理域:
name] switch(enable) set vtp [domain domain-11.在基于IOS的交换机上配置VTP 模式:
switch# vlan database
name switch(vlan)# vtp domain domain-
switch(vlan)# vtp {sever|cilent|transparent} switch(vlan)# vtp password password 在基于CLI的交换机上配置VTP 模式:
switch(enable) set vtp [domain domain-name] [mode{ sever|cilent|transparent }][password password]
12. 在基于IOS的交换机上配置VTP版本:
switch# vlan database
switch(vlan)# vtp v2-mode
在基于CLI的交换机上配置VTP版本:
switch(enable) set vtp v2 enable
13. 在基于IOS的交换机上启动VTP剪裁:
switch# vlan database
switch(vlan)# vtp pruning
在基于CL I 的交换机上启动VTP剪裁:
switch(enable) set vtp pruning enable 14.在基于IOS的交换机上配置以太信道:
switch(config-if)# port group group-number [distribution {source|destination}]
在基于CLI的交换机上配置以太信道:
switch(enable) set port channel moudle/port-range mode{on|off|desirable|auto}
15.在基于IOS的交换机上调整根路径成本:
switch(config-if)# spanning-tree [vlan vlan-list] cost cost 在基于CLI的交换机上调整根路径成本:
switch(enable) set spantree portcost moudle/port cost
switch(enable) set spantree portvlancost moudle/port [cost cost][vlan-list] 16.在基于IOS的交换机上调整端口ID:
switch(config-if)# spanning-tree[vlan vlan-list]port-priority port-priority 在基于CLI的交换机上调整端口ID:
switch(enable) set spantree portpri {mldule/port}priority switch(enable) set spantree portvlanpri {module/port}priority [vlans]
在基于IOS的交换机上修改STP时钟: 17.
switch(config)# spanning-tree [vlan vlan-list] hello-time seconds switch(config)# spanning-tree [vlan vlan-list] forward-time seconds ` switch(config)# spanning-tree [vlan vlan-list] max-age seconds 在基于CLI的交换机上修改STP时钟:
switch(enable) set spantree hello interval[vlan]
switch(enable) set spantree fwddelay delay [vlan]
switch(enable) set spantree maxage agingtiame[vlan]
18. 在基于IOS的交换机端口上启用或禁用Port Fast 特征:
switch(config-if)#spanning-tree portfast
在基于CLI的交换机端口上启用或禁用Port Fast 特征:
switch(enable) set spantree portfast {module/port}{enable|disable} 19. 在基于IOS的交换机端口上启用或禁用UplinkFast 特征:
switch(config)# spanning-tree uplinkfast [max-update-rate pkts-per-second] 在基于CLI的交换机端口上启用或禁用UplinkFast 特征:
switch(enable) set spantree uplinkfast {enable|disable}[rate update-rate] [all-protocols off|on]
20. 为了将交换机配置成一个集群的命令交换机,首先要给管理接口分配一个IP地址,
然后使用下列命令: switch(config)# cluster enable cluster-name
21. 为了从一条中继链路上删除VLAN,可使用下列命令:
switch(enable) clear trunk module/port vlan-range 22. 用show vtp domain 显示管理域的VTP参数.
23. 用show vtp statistics显示管理域的VTP参数.
24. 在Catalyst交换机上定义TrBRF的命令如下:
switch(enable) set vlan vlan-name [name name] type trbrf bridge bridge-num[stp {ieee|ibm}]
25. 在Catalyst交换机上定义TrCRF的命令如下:
switch (enable) set vlan vlan-num [name name] type trcrf {ring hex-ring-num|decring decimal-ring-num} parent vlan-num 26. 在创建好TrBRF VLAN之后,就可以给它分配交换机端口.对于以太网交换,可以采用
如下命令给VLAN分配端口:
switch(enable) set vlan vlan-num mod-num/port-num 27. 命令show spantree显示一个交换机端口的STP状态.
28. 配置一个ELAN的LES和BUS,可以使用下列命令:
ATM (config)# interface atm number.subint multioint ATM(config-subif)# lane serber-bus ethernet elan-name 29. 配置LECS:
ATM(config)# lane database database-name
ATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-address
ATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-address
ATM(lane-config-databade)# name …
30. 创建完数据库后,必须在主接口上启动LECS.命令如下:
ATM(config)# interface atm number
ATM(config-if)# lane config database database-name ATM(config-if)# lane config auto-config-atm-address 31. 将每个LEC配置到一个不同的ATM子接口上.命令如下:
ATM(config)# interface atm number.subint multipoint ATM(config)# lane client ethernet vlan-num elan-num 32. 用show lane server 显示LES的状态.
33. 用show lane bus显示bus的状态.
34. 用show lane database显示LECS数据库可内容.
35. 用show lane client显示LEC的状态.
36. 用show module显示已安装的模块列表.
37. 用物理接口建立与VLAN的连接:
router# configure terminal
router(config)# interface media module/port router(config-if)# description description-string router(config-if)# ip address ip-addr subnet-mask router(config-if)# no shutdown
38. 用中继链路来建立与VLAN的连接:
router(config)# interface module/port.subinterface router(config-ig)# encapsulation[isl|dotlq] vlan-number router(config-if)# ip address ip-address subnet-mask 39. 用LANE 来建立与VLAN的连接:
router(config)# interface atm module/port
router(config-if)# no ip address
router(config-if)# atm pvc 1 0 5 qsaal
router(config-if)# atm pvc 2 0 16 ilni
router(config-if)# interface atm module/port.subinterface multipoint
router(config-if)# ip address ip-address subnet-mask router(config-if)# lane client ethernet elan-num router(config-if)# interface atm module/port.subinterface multipoint
router(config-if)# ip address ip-address subnet-name router(config-if)# lane client ethernet elan-name router(config-if)# …
40. 为了在路由处理器上进行动态路由配置,可以用下列IOS命令来进行:
router(config)# ip routing
router(config)# router ip-routing-protocol router(config-router)# network ip-network-number router(config-router)# network ip-network-number
H3C交换机102条命令使用方法(四)
(2008-01-23 10:11:21)
转载
标签: 分类:IT技术
it
81. 在Cisco设备上设置控制台及vty端口的会话超时:
R1(config)# line console 0
R1(config-line)# exec-timeout 5 10
R1(config)# line vty 0 4
R1(config-line)# exec-timeout 5 2
82. 在Cisco设备上设定特权级:
R1(config)# privilege configure level 3 username R1(config)# privilege configure level 3 copy run start R1(config)# privilege configure level 3 ping R1(config)# privilege configure level 3 show run R1(config)# enable secret level 3 cisco 83. 使用命令privilege 可定义在该特权级下使用的命令:
router(config)# privilege mode level level command
84. 设定用户特权级:
router(config)# enable secret level 3 dallas router(config)# enable secret san-fran router(config)# username student password cisco 85. 标志设置与显示:
R1(config)# banner motd ‘unauthorized access will be prosecuted!’
86. 设置vty访问:
R1(config)# access-list 1 permit 192.168.2.5 R1(config)# line vty 0 4
ss 1 in R1(config)# access-cla
87. 配置HTTP访问:
Router3(config)# access-list 1 permit 192.168.10.7 Router3(config)# ip http sever
Router3(config)# ip http access-class 1 Router3(config)# ip http authentication local Router3(config)# username student password cisco 88. 要启用HTTP访问,请键入以下命令:
switch(config)# ip http sever
89. 在基于set命令的交换机上用setCL1启动和核实端口安全:
switch(enable) set port security mod_num/port_num…enable mac address switch(enable) show port mod_num/port_num 在基于CiscoIOS命令的交换机上启动和核实端口安全:
switch(config-if)# port secure [mac-mac-count maximum-MAC-count]
switch# show mac-address-table security [type module/port]
90. 用命令access-list在标准通信量过滤表中创建一条
记录
混凝土 养护记录下载土方回填监理旁站记录免费下载集备记录下载集备记录下载集备记录下载
:
Router(config)# access-list access-list-number {permit|deny} source-address
[source-address]
91. 用命令access-list在扩展通信量过滤表中创建一条记录:
Router(config)# access-list access-list-number {permit|deny{protocol|protocol-keyword}}{source
source-wildcard|any}{destination destination-wildcard|any}[protocol-specific options][log]
92. 对于带内路由更新,配置路由更新的最基本的命令格式是:
R1(config-router)#distribute-list access-list-number|name in [type number] 93. 对于带外路由更新,配置路由更新的最基本的命令格式是:
R1(config-router)#distribute-list access-list-number|name out [interface-name] routing-process| autonomous-system-number
94. set snmp命令选项:
set snmp community {read-only|ready-write|read-write-all}[community_string] 95. set snmp trap 命令格式如下:
set snmp trap {enable|disable}
[all|moudle|classis|bridge|repeater| auth|vtp|ippermit|vmps|config|entity|stpx] set snmp trap rvcr_addr rcvr_community
96. 启用SNMP chassis 陷阱:
Console>(enable) set snmp trap enable chassis
97. 启用所有SNMP chassis 陷阱:
Console>(enable) set snmp trap enable
98. 禁用SNMP chassis 陷阱:
Console>(enable) set snmp trap disable chassis
99. 给SNMP陷阱接收表加一条记录:
Console>(enable) set snmp trap 192.122.173.42 public
100. show snmp 输出结果。
101. 命令set snmp rmon enable 的输出结果。
102. 显示SPAN信息:
Consile> show span
:em24::em26::em25::em27::em21: