公制螺纹接头内径与软管内径对照表

公制螺纹接头内径与软管内径对照表 公制螺纹接头内径与软管内径对照表Comparison table for inside diameter connector with metric threads to inside diameter conduits 软管CONDUIT 公制螺纹管接头 CONNECTOR WITH METRIC THREAD 标称内径 nominal width NW 内径 Inside ?? nominal 螺纹规格 Thread size 内径 Inside diameter mm nom. ID 标准 excel标准偏差excel标准偏差函数exl标准差函数国标检验抽样标准表免费下载红头文件格式标准下载 standard 公制metric 金属螺纹 metal thread 聚酰胺螺纹polyamide thread 07 10 6.2 M10 - - 10 12 9.6 M12 5.7 8.0 10 12 9.6 M16 - 11.0 12 16 12.0 M16 9.7 11.0 17 20 16.2 M20 13.7 14.6 23 25 22.6 M25 18.6 19.0 29 32 29.0 M32 25.7 26.0 36 40 36.5 M40 33.4 32.0 48 50 47.5 M50 42.7 42.0 48 50 47.5 M63 54.0 53.0 PG 螺纹接头内径与软管内 径对照表 Comparison table for inside diameter connector with PG threads to inside diameter conduits 软管CONDUIT PG制螺纹管接头 CONNECTOR WITH PG THREAD 标称内径nominal width NW 内径 Inside ?? nominal 螺纹规格 内径 Inside diameter mm nom. ID 标准 standard 公制metric Thread size 金属螺纹metal thread 聚酰胺螺纹polyamide thread 07 10 6.2 PG07 - 8.0 10 12 9.6 PG09 9.5 10.0 12 16 12.0 PG11 12.5 13.0 - - - PG13.5 14.5 14.5 17 20 16.2 PG16 16.5 17.5 23 25 22.6 PG21 22.5 22.5 29 32 29.0 PG29 30.5 30.5 36 40 36.5 PG36 40.5 37.5 - - - PG42 - 48.0 48 50 47.5 PG48 52.0 50.0 适用于PMA接头扭矩 Torques for PMA connector PMA 接头螺纹推荐扭矩 / Recommended torques for the PMA connector thread 对带螺纹孔 的开口 / For threaded bore holes 带螺母 / With lock nuts 螺纹组合金属金属 / Thread combination: metal metal 螺纹组合金属聚酰胺或聚酰胺聚酰胺 / Thread combination: metal polyamide or polyamide polyamide 注意以上数据为近似值。在 实际应用中请考虑螺纹的影响。The dates are approximate values. At application please take into account the influence of the counter-thread. 接头带消除应力设计 / Connector to achieve strain relief 当设计和指定安装两个连接点时以下尺寸应要计算在内。 在 每个管接头内的插入长度要额外计算请参照下表。 The following dimensions have to be taken into account if designing and specifying a certain length between two connecting points. The push-in length have to be additionally considered for each connector as mentioned below. 如不正确安装将不能达到指定IP 防水防尘等级。 1. 使用PMACUT 剪切工具剪切软管剪切面与软管轴心垂直。 Straight cut with PMA Cutting tool PMACUT 90o to the conduit axis. 2. 管卡已预先安装推入时轻微转动直 至不能推入为止。 The retaining clip is pre-mounted. Push in with a slight twist until the stop. 3. 轻微回拉软管确保锁紧。 Pull back slightly to ensure the locking mechanism is fully engaged. 4. 在振动或相似情况下的应用建议为保护螺纹最好使用密封胶或黏 合剂。如Loctite Recommendation for applications under vibrations or similar: Protect threads with commercial adhesive or seal compound e.g. Loctite. 5. 安装管接头的软管 部分不要弯曲如果定位请使用管夹或其他支撑。 Do not bend off the PMAFLEX conduit directly after the connector. If necessary destine the direction with a system support or similar. 6. 为安全起见 需用螺丝刀才能开启管夹。 For safety reasons: To re-open a screwdriver has to be used. 1. 使用PMACUT 剪切工具剪切软管剪切面与 软管轴心垂直。 Straight cut with PMA Cutting tool PMACUT 90o to the conduit axis. 2. 软管密封套管接头管夹O 型环或垫圈 Conduit – Seal Cap – Connector - Oval Clip – Flat Gasket or O-ring 3. 将密封套安装于软管末端 根据IEC529/EN60529 标准 防护 等级可达IP68 。 Push seal cap onto end of conduit to achieve an ingress protection up to IP68 according to IEC 529 / EN 60529. 4. 为安装方便 密封套可使用水或润滑剂来 润滑。 For ease of installation moisten seal cap with water or lubricant. 5. 将带密封套 的软管完全推进接头。如果密封套没有完全安装好管卡将不能安装 Push conduit with seal cap with slight twist fully into connector. For safety reasons retaining clip will not fit if seal cap is not fully installed. 6. 推进管卡直至完全配合。确保管卡缺口部位 在软管侧 Push in the Retaining Oval Clip until the barbed hooks are optimal set. Ensure that the opening slot of the retaining clip is on conduit side 7. 在振动或相似情况下的 应用建议为保护螺纹最好使用密封胶或黏合剂。如Loctite Recommendation for applications under vibrations or similar: Protect threads with commercial adhesive or seal compound e.g. Loctite. 8. 安装接头的软管部分不要弯曲 如果定位请使用管夹或其 他支撑。 Do not bend off the PMAFLEX conduit directly after the fitting. If necessary destine the direction with a system support or similar. 9. 为安全起见 需用螺丝刀才能 开启管夹。 For safety reasons: To re-open a screwdriver has to be used.