热熔胶MSDS英文版
SAFETY DATA SHEET
PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS
1 CHEMICAL PRODUCT AND COMPANY IDENTIFICATION PRODUCT
Product Name: HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS
Product Description: HOT MELT ADHESIVE,MIXTURE
Product Code:
Intended Use: ADHESIVE,FOR AUTOMOBILE LAMPS
COMPANY IDENTIFICATION
Huangshan Xiuning Xindecheng Chemical Co., Ltd. SUPPLIER:
Wanning Industrial Park, Huangshan, Anhui, China (245400)
Telephone: 0086-559-7519970
Facsimile: 0086-559- 7519971
This (M)SDS is a generic document with no country specific information included.
2 COMPOSITION/INFORMATION ON INGREDIENTS
No Reportable Hazardous Substance(s) or Complex Substance(s).
INGREDIENTS CAS No. Approx. Proportion
styrene butadiene rubber 9003-55-8 Med 50-60%
rosin resin 8050-09-7 Low 50-40%
Page 1 of 5
SAFETY DATA SHEET
PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS
3 HAZARDS IDENTIFICATION
This material is not considered to be hazardous.
PHYSICAL / CHEMICAL HAZARDS
N/A
HEALTH HAZARDS
No adverse effects due to inhalation are expected. When heated, the vapour/fumes given off may cause respiratory
tract irritation.
4 FIRST AID MEASURES
INHALATION
In case of adverse exposure to vapors and / or aerosols formed at elevated temperatures, immediately remove the
affected victim from exposure. Administer artificial respiration if breathing is stopped. Keep at rest.
SKIN CONTACT
Wash contact areas with soap and water. For hot product: Immediately immerse in or flush affected area with large
amounts of cold water to dissipate heat. Cover with clean cotton sheeting or gauze and get prompt medical attention. EYE CONTACT
Flush thoroughly with water. If irritation occurs, get medical assistance.
INGESTION
First aid is normally not required. Seek medical attention if discomfort occurs.
5 FIRE- FIGHTING MEASURES
Page 2 of 5
SAFETY DATA SHEET
PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS
EXTINGUISHING MEDIA
Appropriate Extinguishing Media: Use dry chemical or carbon dioxide (CO) to extinguish flames. 2
Inappropriate Extinguishing Media: Straight streams of water
FIRE FIGHTING
Fire Fighting Instructions: Assure an extended cooling down period to prevent re-ignition. Evacuate area. Prevent
run-off from fire control or dilution from entering streams, sewers or drinking water supply.
Hazardous Combustion Products: Flammable hydrocarbons, Oxides of carbon, Smoke, Fume, Incomplete
combustion products
6 ACCIDENTAL RELEASE MEASURES
NOTIFICATION PROCEDURES
In the event of a spill or accidental release, notify relevant authorities in accordance with all applicable regulations.
ENVIRONMENTAL PRECAUTIONS
N/A
7 HANDLING AND STORAGE
HANDLING
Avoid elevated temperatures for prolonged periods of time. Protect material from direct sunlight. Material can
accumulate static charges which may cause an electrical spark (ignition source). Apart from the specific nature of the
polymer product, conditions such as humidity, sunlight and temperature.
Loading/Unloading Temperature: [Ambient]
Transport Temperature: [Ambient]
Page 3 of 5
SAFETY DATA SHEET
PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS
STORAGE
Store in a cool, dry place.
Storage Temperature: 0?—40?
Storage Pressure: [Ambient]
8 EXPOSURE CONTROLS /PERSONAL PROTECTION
ENGINEERING CONTROLS
N/A
PERSONAL PROTECTION
Personal protective equipment selections vary based on potential exposure conditions such as applications, handling
practices, concentration and ventilation. Information on the selection of protective equipment for use with this
material, as provided below, is based upon intended, normal usage.
Respiratory Protection:
If engineering controls do not maintain airborne contaminant concentrations at a level which is adequate to protect
worker health, an approved respirator may be appropriate. Respirator selection, use, and maintenance must be in
accordance with regulatory requirements, if applicable. Types of respirators to be considered for this material
include:
No special requirements under ordinary conditions of use and with adequate ventilation.
For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode.
Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate, gas/vapour
warning properties are poor, or if air purifying filter capacity/rating may be exceeded.
Hand Protection:
If product is hot, thermally protective gloves are recommended. If contact with forearms is likely, wear gauntlet style
gloves.
Page 4 of 5
SAFETY DATA SHEET
PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS
Eye Protection:
If contact is likely, safety glasses with side shields are recommended.
Skin and Body Protection:
If product is hot, thermally protective, chemical resistant apron and long sleeves are recommended. Specific Hygiene Measures:
Always observe good personal hygiene measures, such as washing after handling the material and before eating,
drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Discard
contaminated clothing and footwear that cannot be cleaned. Practice good housekeeping.
9 PHYSICAL AND CHEMICAL PROPERTIES
Typical physical and chemical properties are given below. Consult the Supplier in Section 1 for additional data. GENERAL INFORMATION
Physical State: Solid
Form: Grains
Colour: Gray
Odour: None to Mild
IMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATION
Relative Density (at 18 C): 0.97
Density (at 18 ºC): 970 kg/m?
Flash Point [method]: O.C Cleveland Open Cup ,260?
Flammable Limits (Approximate volume % in air): LEL: N/D UEL: N/D
Autoignition Temperature: N/A
Page 5 of 5
SAFETY DATA SHEET
PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS
Boiling Point / Range: ,260?
Vapour Density (Air = 1): N/A
Vapour Pressure: N/A
Evaporation Rate (N-Butyl Acetate = 1): N/A
pH: N/A
Log Pow (n-Octanol/Water Partition Coefficient): N/A
Solubility in Water: Negligible
10 STABILITY AND REACTIVITY STABILITY:
Material is stable under normal conditions. CONDITIONS TO AVOID:
Avoid elevated temperatures for prolonged periods of time.
HAZARDOUS DECOMPOSITION PRODUCTS:
Material does not decompose at ambient temperatures. HAZARDOUS POLYMERIZATION:
Will not occur.
11 TOXICOLOGICAL INFORMATION
Page 6 of 5
SAFETY DATA SHEET
PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS
Acute Toxicity
Route of Exposure Conclusion / Remarks
INHALATION
Toxicity: Minimally Toxic. Based on test data for structurally similar
materials.
Irritation: Negligible hazard at ambient/normal handling temperatures. Based
on test data for structurally similar materials.
INGESTION
Toxicity: Minimally Toxic. Based on test data for structurally similar
materials.
Skin
Toxicity: Minimally Toxic. Based on test data for structurally similar
materials.
Irritation: Negligible irritation to skin at ambient temperatures. Based on test
data for structurally similar materials.
Eye
Irritation: May cause mild, short-lasting discomfort to eyes. Based on test
data for structurally similar materials.
CHRONIC/OTHER EFFECTS
12 ECOLOGICAL INFORMATION
The information given is based on data available for the material, the components of the material, and similar materials.
ECOTOXICITY
Page 7 of 5
SAFETY DATA SHEET
PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS
Material -- Not expected to be harmful to aquatic organisms.
Material -- Not expected to be harmful to terrestrial organisms
13 DISPOSAL CONSIDERATIONS
Disposal recommendations based on material as supplied. Disposal must be in accordance with current applicable laws
and regulations, and material characteristics at time of disposal.
DISPOSAL RECOMMENDATIONS
Suitable routes of disposal are supervised incineration, preferentially with energy recovery, or appropriate recycling
methods in accordance with applicable regulations and material characteristics at the time of disposal.
14 TRANSPORT INFORMATION
LAND : Not Regulated for Land Transport
SEA (IMDG) : Not Regulated for Sea Transport according to IMDG-Code
AIR (IATA) : Not Regulated for Air Transport
15 RRGULATORY INFORMATION
Page 8 of 5
SAFETY DATA SHEET
PRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS
Material is not hazardous as defined by the EU Dangerous Substances/Preparations Directives.
16 OTHER INFORMATION
N/D = Not determined, N/A = Not applicable
THIS SDS COVERS THE FOLLOWING MATERIALS: Petroleum hydrocarbon resin ECR 807 | Escorez 2203 LC |
mixed resin dust
-----------------------------------------------------------------------------------------------------------------------------------------------------
The information and recommendations contained herein are, to the best of Xindecheng’s knowledge and belief, accurate
and reliable as of the date issued. You can contact Xindecheng to insure that this document is the most current available from Jinsen. The information and recommendations are offered for the user's consideration and examination. It is the user's responsibility to satisfy itself that the product is suitable for the intended use. If buyer repackages this product, it is
the user's responsibility to insure proper health, safety and other necessary information is included with and/or on the container. Appropriate warnings and safe-handling procedures should be provided to handlers and users. Alteration of this document is strictly prohibited.
---------------------------------------------------------------------------------------------------------------------------
Page 9 of 5
本文档为【热熔胶MSDS英文版 】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑,
图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。