投影机检验规范

投影机检验规范 文件編號DOC #: 文件名稱 Document Title: XXXXXXXXX ASSEMBLY VISUAL 版次 Rev INSPECTION CRITERIA A 1.0 目的:訂定產品之組,外觀檢驗規範,以,品質保證之推,。 2.0 範圍:凡屬本公司所有產品之組,外觀檢驗,均適用本規範。 3.0 權責:本公司所有產品之組,外觀檢驗依本規範實施。 4.0 ,考文件 / 相關文件: 中華民國品質學會發, COSMETIC DEFCETS SCALE CHART (EFA QC-C0192) 。 5.0 名詞定義: N/A 6.0 作業內容: 6.1 三個次缺(Minor) , 一個主缺(Major) 。 6.2 檢驗條件:將待測物置於正常照,下,,眼距待測物以30 cm 檢驗之,每面檢驗時間約5~7秒。 6.3 檢查區域:檢查面依產品組,後之位置可分為,、,、,三區 6.3.1 ,區:產品於使用者正面可,部分,如面板、上蓋Logo 面。 6.3.2 ,區:產品於使用者正面,可,部分,如背面、側面。 6.3.3 ,區:產品底面部分。 6.4 檢查項目及判定標準: Note : Inspection section : divide into A, B, C three section. A section : top, logo side. B section : rear, flank side. C section : bottom side. This document is the exclusive property of Unihan and shall not be reproduced or copied or transformed to any other format without prior permission of Unihan. Page: 1 of 4 本資,為永碩聯合國際專有之財產, 非經許可, ,得複製, 翻印或轉變成其他形式使用. 文件編號DOC #: 文件名稱 Document Title: XXXXXXXXX ASSEMBLY VISUAL 版次 Rev INSPECTION CRITERIA A CLASSIFICATION OF INSPECTIDEFECTS No DESCRIPTION OF DEFECTS ON ITEM Critical Major Minor 1.PLASTIC 1.1 Scrapes, grates, or scratches exposed base materials. V CASE Scrapes, grates, or scratches exposed no base (塑膠機構) 1.2 V materials on Logo Area. Scrapes, grates, or scratches exposed no base materials, sized A area over 0.1 mm (W), 5 mm(L) 1.3 V B area over 0.15 mm (W), 5 mm(L) C area over 0.2 mm (W), 6 mm(L) 2.1 Dust, Grit on Logo Area V Dust, Grit : A area over 0.1 mm2, B area over 0.15 2.2 V mm2, C area over 0.2 mm2 Dust, Grit A area under 0.1 mm2, 3 points is permitted (total) 2.3 V B area under 0.15 mm2, 3 points is permitted (Total) C area under 0.2 mm2, 3 points is permitted (Total) 3.1 V Pit φ over 3mm x 0.1mm (Length x Width) Pit φ under 1mm2 : 3.2 V Section A : not allowed, Section B <2, Section C <3. Pit φ under 1mm2: 3.3 V Section B >2, Section C >3. 3.4 V Pit φ over 1mm2. 4.1 Burr over 0.08mm. V This document is the exclusive property of Unihan and shall not be reproduced or copied or transformed to any other format without prior permission of Unihan. Page: 2 of 4 本資,為永碩聯合國際專有之財產, 非經許可, ,得複製, 翻印或轉變成其他形式使用. 文件編號DOC #: 文件名稱 Document Title: XXXXXXXXX ASSEMBLY VISUAL 版次 Rev INSPECTION CRITERIA A CLASSIFICATION OF INSPECTIDEFECTS No DESCRIPTION OF DEFECTS ON ITEM Critical Major Minor 4.2 Burr under 0.08mm, but hard and sharp. V Electroplate : ripples, erosion, rust, bubbles, cracks, 5 V and electroplating surface peeled off. Paint Coating and Cosmetic: ? Paint stripe. 6.1 ? Uneven colors, visible material foundation color V and spray trace. ? Paints peeled, blister and crack. 6.2 Color and luster : Section A, B mixed or blur. V 6.3 Color and luster : Section C mixed or blur V Color checking : The ΔE >1.0 6.4 V 7.1 Printed letters : Missing, and vague. V Printed letters : V 7.2 Letters offset > 0.5mm and Inclination > 0.5? Materials shortage on appearance and structure. V 8 Mechanism assembly : Deformation, mistaken V 9.1 match. Mechanism assembly : Missing screws, loosen V 9.2 screws, or worn screw. This document is the exclusive property of Unihan and shall not be reproduced or copied or transformed to any other format without prior permission of Unihan. Page: 3 of 4 本資,為永碩聯合國際專有之財產, 非經許可, ,得複製, 翻印或轉變成其他形式使用. 文件編號DOC #: 文件名稱 Document Title: XXXXXXXXX ASSEMBLY VISUAL 版次 Rev INSPECTION CRITERIA A CLASSIFICATION OF INSPECTIDEFECTS No DESCRIPTION OF DEFECTS ON ITEM Critical Major Minor 1 Front panel : discolor. V 2.FRONT 2 The front panel overruns the designated position. V PANEL There are scrapes, cracks, bend traces on the front (銘板) 3 V panel. 1 LED LIGHT : wrong color. V 3.LED LAMP 2 LED LIGHT : wrong status. V (指示燈) 3 LED LIGHT : scratch or broken. V 1 LABEL : no label or wrong serial number. V 2 LABEL : wrong position. V LOGO : the letters and symbol are vague, missing, V 3 4.LABEL or shadow. (標籤) LABEL : exceeds the edge of machine. V 4 LABEL : inclined 1.5mm or over. V 5 LABEL : uneven or bend. V 6 5.FOOT Missed or unattached. V 1 PAD Shift outside designated position. V 2 (腳墊) This document is the exclusive property of Unihan and shall not be reproduced or copied or transformed to any other format without prior permission of Unihan. Page: 4 of 4 本資,為永碩聯合國際專有之財產, 非經許可, ,得複製, 翻印或轉變成其他形式使用.