首页 1250-1050扫地机说明书

1250-1050扫地机说明书

举报
开通vip

1250-1050扫地机说明书1250-1050扫地机说明书 〓 目 录 〓 非常感谢您选择我们的产品~扫地车投入使用前~请仔 一、扫地车概况„„„„„„„„„„„„1 细阅读完本指南中的说明~并严格遵照执行~以达到最佳的 1、扫地车外形尺寸 清扫效果并延长机器寿命。本电动扫地车执行标准为欧共体2、技术参数 3、操作系统 98/37/EEC标准。您有什么意见和建议请与我们联系。我们 4、安全规范概要 热忱、快捷为您服务。 二、扫地车的操作„„„„„„„„„„„6 1、预防措施 2、操作程序 WARING!注 意 ::: 3、操作规程...

1250-1050扫地机说明书
1250-1050扫地机说明书 〓 目 录 〓 非常感谢您选择我们的产品~扫地车投入使用前~请仔 一、扫地车概况„„„„„„„„„„„„1 细阅读完本指南中的说明~并严格遵照执行~以达到最佳的 1、扫地车外形尺寸 清扫效果并延长机器寿命。本电动扫地车执行MATCH_ word word文档格式规范word作业纸小票打印word模板word简历模板免费word简历 _1714287036767_0为欧共体2、技术参数 3、操作系统 98/37/EEC标准。您有什么意见和建议请与我们联系。我们 4、安全 规范 编程规范下载gsp规范下载钢格栅规范下载警徽规范下载建设厅规范下载 概要 热忱、快捷为您服务。 二、扫地车的操作„„„„„„„„„„„6 1、预防措施 2、操作程序 WARING!注 意 ::: 3、操作 规程 煤矿测量规程下载煤矿测量规程下载配电网检修规程下载地籍调查规程pdf稳定性研究规程下载 三、边刷„„„„„„„„„„„„„„„8 1、本机器仅作为清扫工具~如超出本指南中的说明而作为其 1、边刷的装配 他用途~我们不承担由此造成的任何损害的责任。 2、边刷的调整 3、边刷的更换 2、本扫地车可清扫一般的垃圾~不宜清扫绳丝、有毒有害、 四、主刷„„„„„„„„„„„„„„„10 高温杂物~以免缠绕、灼烫主刷和边刷~使其不能正常工作。 1、主刷的调整 2、检查及更换主刷驱动传送带 3、本机器只能由授权及训练的人员使用。 3、拆卸及更换主刷 4、本机器停止工作时~必须停放在平整的地方。 五、皮带张紧„„„„„„„„„„„„„13 六、驱动系统„„„„„„„„„„„„„14 5、当机器开始使用时~应该让无关人员及孩子们离开现场。 七、方向系统„„„„„„„„„„„„„14 八、刹车制动系统„„„„„„„„„„„15 6、打开机罩或机器维护和检修时必须关闭电源钥匙。 九、吸尘风机„„„„„„„„„„„„„15 7、当运输清扫车时~确认它已被牢固地绑在运输车上。 十、挡尘板„„„„„„„„„„„„„„16 十一、灰尘过滤器„„„„„„„„„„„„16 8、确保电池充电时处在通风场所。扫地车停止工作后或运行十二、集尘箱„„„„„„„„„„„„„„17 时出现欠压报警~应及时给电瓶充电~以便延长电池寿命。 十三、电气系统„„„„„„„„„„„„„18 十四、定期维护与检查„„„„„„„„„„18 9、当您完成工作时应及时拔掉钥匙~避免扫地车未认可的使十五、故障维修„„„„„„„„„„„„„19 用。 十六、充电机的使用说明„„„„„„„„„21 十七、蓄电池的使用说明„„„„„„„„„25 acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership ?主刷+右边刷„„„„„„„„„„„1050mm(1250mm) 1 ※一、扫地车概况 ※ ?主刷+两侧边刷„„„„„„„1050 mm(1250 mm) ?主刷„„„„„„„„„„„„„„„„700 mm ? ASD 1050、1250型扫地车外形尺寸 9、驱动„„„„„„„„„„„„ 通过后轮的电机 宽×长×高: ASD1050型 1050×1500×1150 10、垃圾箱 ASD1250型 1250×1500×1150 ?容量„„„„„„„„„„„„„„„„„„135升 ?倒空 „„„„„„„„„„„手动抽出并带有轮子 ? 技术参数 11、灰尘过滤系统 1、电机 过滤器数量„„„„„„„„„„„„„„„„„4只 12、灰尘过滤系统的清理 ?驱动电动机„„„„„„„„„„„„„„36V,600W 电子振打系统„„„„„„„„„„„„„„36V-150W ?刷子驱动电动机„„„„„„„„„„„„36V,600W 13、真空负压系统 ?风机„„„„„„„„„„„„„„„„„36V,200W ?风机类型„„„„„„„„„„„„„„„„„离心 ?过滤器振打电动机„„„„„„„„„„„36V,150W ?风机驱动„„„„„„„„„„„„„直流电机驱动 2、轮子 ?吸风口开关„„„„„„„„„„„„„„拉线开关 ?前轮„„„„„„„„„„„„„„„„„„橡胶轮胎 14、主刷 ?后轮„„„„„„„„„„„„„„„„„„橡胶轮胎 ?主刷类型„„„„„„„„„„„„„„„„圆柱型 3、方向 ?宽度„„„„„„„„„„„„„„„„„„700mm ?方向盘与轴联接„„„„„„„„„„„„„„在前轮 ?升降系统„„„„„„„„„„„„„„„杠杆联结 ?最小转弯半径„„„„„„„„„„„„„„„1000MM 15、边刷 4、闸——停车闸在后轮,以机械踏板联结。 ?边刷类型„„„„„„„„„„„„„„„„圆锥型 5、重量——机器重量430 kg?数量„„„„„„„„„„„„„1只(1250型2只) 。 ?升降系统„„„„„„„„„„„„„„„杠杆联结 6、运动参数 16、电气系统 (1)工作速度MAX„„„„„„„„„„„„„„7km/h ?电压„„„„„„„„„„„„„„„„„„„36V (2坡角度MAX„„„„„„„„„„„„„„„„„20% ?电瓶6只„„„„„„„„„„„„„„6 V -120Ah 7、噪音水平 ?电解质„„„„„„„„„„„„„„„„„蒸馏水 工作状态下的噪音水平„„„„„„„„„„„„„71dB ?使用时间„„„„„„„„„„„„„„„6-8小时 8、清洁宽度 , 提示:使用时间取决于电池性能及机器的工作状态。 acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership 子的部分磨损(见“主刷——调节主刷”章节)。 2 3 ? 扫地车的开关、按钮及部件功能(见图一) ?电源开关 当钥匙向右转动打开电源,向左转动关闭电源。 ?作业开关 按此开关,能使风机、主刷及边刷运转作业。 ?边刷升/降手柄 当移动机器或完成清扫作业时,将杠杆向前推(提起边 刷);当进行清扫作业时将杠杆拉回(落下边刷)。 WARING!注意:机器停止作业杠杆推起(升起状态) ?前进/倒车转换开关 开关6选择前进/倒车方向,踩踏板10可以移动。 ?刹车踏板 踩刹车踏板7是通过向后轮施压来刹车。 ?挡尘板踏板 踩此踏板可以使挡尘板上升,以便使轻而大的垃圾进入 主刷清扫区。否则垃圾会被挡尘板挡住,随同扫地车推向前 方。 ?照明灯开关/指示灯 按此开关,大灯亮。适合光线暗或夜间清扫作业;当扫 地车在马路或公共场所作业时,打开指示灯提示行人。 ?调速器踏板 扫地车前进/倒车速度由此控制,如汽车油门踏板一样。 (图一) ?振打开关 拉动开关可激活过滤器振动器马达进行振打。 ? 喇叭按扭 按此开关喇叭鸣叫 ?安全规范概要 ?主刷升/降手柄 在使用电动清扫车之前,必须事前检查,机器有无异常 拉动此杠杆可以使主刷处于工作状态,工作完成后提起响声。 WARING!警告~ 主刷。此杠杆的特点是可以调节主刷与地面的高度,当作业 机器只能由授权的操作人员使用,操作人员离开时,及一段时间后,主刷上的刷毛被磨短,调节此杠杆可以弥补刷acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership 时拔掉电源开关钥匙,以免未经批准的人使用。 5 4 ※ 二、扫地车的操作 ※ 在接通和发动机器之前,对其进行检查,无论何时何地, 不能使机器在不稳定不正常的情况下工作。 1、预防措施 WARING!警告~ ?机器外壳打开后,复位时必须安装正确、可靠; ?扫地车要由专职人员使用; ?如果机器外壳被拆下,不管任何原因,在机器投入工作前, ?在离开无人看护的扫地车时,必须拔掉开关钥匙; 必须将它们恢复到正常状态; ?只能在正确的条件下使用机器,并遵照它的用途; ?扫地车完成作业时应提升刷子,防止刷子变形; ?根据机器的用途,严格按照本指南指定检查和维护要求; ?不要将扫地车停放在倾斜的地方; ?绝对禁止机器吸入易燃或毒性液体; ?接触机器的运动机件是危险和绝对禁止的,确因工作需要,WARING!警告:在扫地车使用之前,要检查电池内电解液的深首先要关闭电源并拔去钥匙。 度。 2、扫地车操作程序 ?操作员坐入机器驾驶座; ?打开钥匙,接通电源; ?按前进/倒退开关,扫地车前进/倒退正常; ?按作业开关,主、边刷及风机运转正常; ?转动主刷升/降手柄,主刷与地面接触,处于作业状态; ?转动边刷升/降手柄,边刷与地面接触,处于作业状态; ?清扫一段时间,如灰尘较多,应周期使用振打器清除过滤 器。 WARING!注意:在上述?-?步骤中有不正常现象出现或有异 常响声,必须断开电源进行检查。 acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership 6 7 3、操作规程 ※三、边刷(图示二)※ ?不能清扫绳子、金属丝、皮带、水等; ?清扫大而轻的垃圾(譬如纸、树叶等),踩挡尘板踏板使机 器的前挡尘板上升,以便更容易将这些垃圾吸上; ?间隔一定时间,振打过滤器。使过滤器上灰尘掉入集尘箱, 使过滤器风阻变小,避免清扫时扬尘和二次污染。间隔时间 视粉尘多少而定; ?不要吸入未熄灭的烟头或炽热材料; ?不要让无关人员接近机器,特别是小孩; ?机器必须由专人负责,他应该熟悉本 手册 华为质量管理手册 下载焊接手册下载团建手册下载团建手册下载ld手册下载 的内容; ?操作者应身心健康,操作期间不得饮酒; ?机器接通后没有发出异常响声。如果存在异常响声,要立 刻停止并查明原因。 (图二) WARING!警告 1、装配刷子的螺丝 所有维护、检修或修理工作必须由专业人员或授权服务 边刷可以清扫地面边缘及角落的垃圾,边刷将边角的垃中心来做。 圾扫至中间再由主刷扫入集尘箱。 2、调整边刷 边刷使用一段时间后,刷毛被磨损后与地面不能接触, acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership 影响清扫效果。按照图二所示可调节边刷的高度,方法如下: ?边刷1; 8 9 ?松开螺母2; ※ 四、主刷(图示三、四) ※ ?逆时针旋转把手3直至边刷的外侧与地面接触即可; ?重新拧紧螺母2; ?运转刷子并检查缆绳。 3、更换边刷 ?卸下螺母4; ?按5所示方向拆下旧刷子; ?安上新刷子并调节其高度; WARING!警告:当清扫车静止的时候,必须将边刷提起,避免 变形(刷子的磨损弯曲)。 (图三) acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership 2、调节和更换主刷传动带(如图三所示) 每工作100-150小时,检查主刷传动带5的松紧情况。若皮 带太松适度线紧,若磨损严重需更换。具体方法如下: ?打开右边盖1; ?退下传动带2; ?从皮带轮3上卸下传送带2; ?松掉皮带张紧轮4,从皮带轮3上卸下主刷传动带5; (图四) ?更换主刷传送带5在皮带轮3上; 11 10 ?安装反之。利用张紧轮4拉紧传送带5; 主刷是把清扫的垃圾扫入后面的集尘箱内。 ?在皮带轮3上把传动带2安到原位; WARING!警告 ?利用电机皮带轮拉紧传动带2; 决不清扫绳子电线等绳丝状杂物,否则会卷入主刷并损 ?盖上防护板1。 坏毛剌。 更换主刷传动带时,同样应该对传动带2,如果皮带有1、调节主刷高度(如图三所示) 磨损,要同时更换,以避免今后更换时需拆除更多的零件。 主刷依靠手柄7进行升降,通过调节7,可使主刷升降。 3、拆卸及更换主刷(如图四所示) 主刷装在一个活动的机构上。主刷要正确地接触地面,当它 从清扫车的侧面可以拆卸主刷。 旋转时与地面接触宽度约3CM。 ?打开主刷防护板1; 如果主刷漏过树叶或留下成行的灰尘,说明主刷毛剌磨 ?拧下螺丝2; 损,应该使它下降,调节方法如下: ?拆开联动杆3; ?松下螺母6; ?拉开弹簧4; ?顺时针旋转手柄直至主刷与地面接触宽度约3CM; ?拆下内护板5; ?重新拧紧螺母6。 acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership ?卸下刷子端盖轴6后可方便地拿出主刷; 2、移动张紧轮1直至皮带正确张紧; ?安装主刷反之; 3、重新拧紧螺栓3。 ?装配好刷子,联动杆3上的小孔必须与柱头螺栓紧密联结; WARING!警告:必须正确张紧皮带~不能太紧,否则会使轴承?拧紧螺丝2,直至联动杆与主刷端轴啮合。 承受过分的压力。 WARING!注意~~ 主刷安装后如7,主刷反向运转会影响清扫效果,在电 路接线时颠倒了正负极,可导致主刷反向动转。 12 13 ※五、 皮带张紧(图示五) ※ ※ 六、驱动系统(图示六) ※ (图六) (图五) 扫地车电机驱动系统包括电机1、过桥差速齿轮箱2,倒 /顺转换开关,可使机器向前或向后行驶。通过踩调速器踏板每工作40个小时后,要检查张紧轮1与皮带2配合的情 可控制行驶速度(0-7公里/小时)。 况,如果皮带松驰,按下列所示张紧: 1、松开皮带2的张紧轮1上的螺栓3; acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership ※ 七、方向系统 ※ 扫地车是依靠方向盘来驾驶的,无关人员禁止操作方向盘。 (图八) 吸尘风机是把将清扫过程中扬起的灰尘吸进集尘箱。吸 尘风机是由电机2带动风叶轮1旋转。 15 14 挡尘板 ※ ※ 十、 ※ 八、刹车制动系统(图示七)※ 挡尘板是防止清扫过程中的垃圾飞溅出来。 , 更换挡尘板 1、松开固定螺栓,拆下破旧或损坏的挡尘板。 2、安装一块新的挡尘板,用螺栓固定在同样的位置,侧面及 后方的挡尘板距离地面约3-4毫米。 ※ 十一、灰尘过滤器(图示九)※ (图七) 刹车是为了行驶中的电动扫地车停止运动 1、刹车作用是由后轮上的毂提供的。 2、踏板制动1是机械型的,刹车时操作不当易刹车踏板造成 损坏,不要猛踩刹车踏板,这样易使刹车线断裂。 3、刹车不灵,调节刹车线2即可。 (图九) 打开过滤器箱盖,去掉吸入的灰尘。过滤器必须保持高※ 九、吸尘风机(图示八)※ acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership 的除尘效率。 (图十) WARING!注意: 图例1——插入集尘箱 如果灰尘冒出外面,说明过滤器是脏的,要及时清洁。 图例2——装上集尘箱 清洁过滤器。 每当扫地车在清扫期间扬尘时,要及时清洁过滤器,清图例3——完整后 洁方法如下: 安装集尘箱方法如下: 1、拉起振打开关约10秒钟。 提示:不要长久拉上振打开关,否则易损坏电气系统。 将集尘箱前部完全推进机器中,如图十所示。后方边2、大约每月清洁保养过滤器一次,将过滤器拿出彻底清洁, 缘必须与钩子相吻合,这样集尘箱不会漏气。 使之与真空吸尘器相匹配。清洁从里面开始,去掉积聚的灰 尘。必要时更换过滤器,注意将橡胶密封条与收尘箱底部的 孔相吻相,以防漏气。 16 17 ※ 十二、集尘箱(图示十)※ ※十三、 电气系统 ※ 电气系统由6只6V电池供给动力,系统电压为36V、 120AH。 扫地车开始作业前蓄电池应充满 。清扫车作业一段时间 后,蓄电池电量下降,当低于一定值时,电脑提示报警或驱 动不走,这时关掉刷子,才能行走,应及时给蓄电池充电。 否则会影响蓄电池使用寿命。 ※ 十四、定期维护和检查 ※ acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership 每隔多少小时 清扫不彻底,留下纸前面挡尘板提升机修理挡尘板,踩脚踏板使定期维护和检查 8 40 150 500 1500 屑、树叶或其它垃圾 构没有工作 之能升降 1 电池电解液检查标准 ? 前挡尘板损坏升不垃圾往前窜 更换前挡尘板 2 驱动电机的碳刷检查 ? 了 3 风机碳刷的检查 ? 主刷卷起前挡尘板 前挡尘板太久了 更换前挡尘板 主刷边刷是否有线、丝4 ? 刷子压得太紧 减小刷子压力(调张紧缆物缠绕 刷子磨损太快 绳) 地板非常粗糙 5 检查和清洁过滤器 ? 6 检查仪表板 ? 主刷工作时噪音大 刷子有丝绳缠绕 除去杂物 7 检查边刷的磨损情况 ? 刷子工作时不旋转 传动皮带损坏 更换传动皮带 8 检查皮带张力 ? 刷子及风机电机不保险丝熔断 更换保险丝 工作 (表格一) 18 ※ 十五、故障维修 ※ 19 问题 原因 处理办法 问题 原因 处理办法 驱动电机电缆断 检查接线 踏板调速器损坏 维修调速器 驱动电机工作时既工作速度太快 降低工作时的速度 不前进也不能倒车 控制开关损坏 换开关 清扫车漏过大的树刷子压力太小 调节刷子压力 保险丝熔断 更换保险丝 叶或大的垃圾颗粒 刷子毛变形或被丝电解液水偏低 加满电解液 除去绳子或铁丝 线缠绕 电池烧坏 更换电池 电池不能充电 清扫车在地板上留过滤器被堵塞 清洁过滤器 充电器 检查充电器输入电流 下尘土或尘土来自挡尘板损坏 检查挡尘板,如损坏则更电池接线端松驰 检查并拧紧电池接线端 侧面挡尘板 换 垃圾缠绕在主刷上 除去杂物 主刷转不动、噪音大 轴承坏 更换轴承 acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership 减小刷子压力(张紧缆刷子过压 使用条件 绳) 充电时间不足 增加充电时间 , 储运环境温度:-40?,80?。 电池放电过快 电池烧坏 更换电池 , 工作环境温度:-25?,45?,直接邻近电子元器件处的开关有毛病 更换开关 空气温度最高不超过70?。 保险丝烧坏 更换保险丝 。 , 工作环境温度:相对湿度小于85%电机负荷过大引起: 电动振打装置不工 作 1、电机电刷坏了 更换 , 海拔高度:不超过2500m。 2、轴承磨损 更换 3、电机线圈烧坏 更换 充电机外型及说明 电动振动过大 (见上述) 电动机振动过大,保 保险丝有毛病 更换保险丝 险丝冒火花 短路 检查电路 检查输入输出电压,报警刷子可以正常工作,电路板、保险丝、驱 信号,指示灯,保险丝,但不能正常行驶 动电机、调速器问题 驱动电机,连接线路。 (表格二) 21 20 ※十六、充电机使用说明※ 智能充电机使用步骤 , 将充电机的输出线与被充蓄电池正负极两端可靠连接,技术参数 其中红线接正极,黑线接负极(注意:严禁正负极接反)。 , 输入交流电压:单相220V?10%。 , 在确定输入电源插座的电压后,接通充电机电源,合上, 输出直流电压:36V+10% 电机电闸,此时充电机对蓄电池自动充电。 , 输出直流电流: 30A , 充电程度如下: 电压升高到整定点 , 均衡充电电流:电瓶容量的4%。 蓄电池 恒流充电1/10C,1/5C 恒压充电 , 电压采样精度:,1%。 此时容量已充到80%以上 , 电流采样精度:,1%。 电池减小到整定值充足灯亮 , 蓄电池电压:6×6V 充足停充 此时蓄电池容量已达95%以上 acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership , 充电机应立式放置,在干燥通风环境中进行,避免潮 湿,远离易燃易爆品。 , 该充电机具有以下功能: , 恒流充电:不论蓄电池如何欠压,都能以额电流限流, 在电池充满的条件下,先断开输入交流电源,后断开 恒流充电,避免了欠压蓄电池前期过流充电的现象。 充电机与电池之间的连线。 , 恒压充电:蓄电池经过恒流充电,电压升高到整值,, 在无人或者长期不用的条件下,必须断开交流电源。 自动转为恒压充电,这时容量已达80%左右,充电电 , 充电过程中不要覆盖充电机,使用环境温度不大于源逐渐减小。在充电后期,恒压充电,减小电瓶析气 40? 和极化,提高电池寿命。 , 充电指示,继续恒压小电流充电,电池容量达到95%, 此充电机仅限于户内使用,谨防雨淋。 以上,充足灯亮,停止充电。 , 禁止给不可再充电的电池充电。 , 均衡充电:为避免电池单体落后及寒冷地区的电池和, 再次开机间隔时间不少于10秒(切断输入电源)。 旧电池的充电不足,本机特设均充功能,电池充足后, 按一下均充键,进行均充,2小时自动停充。可补充 附录:性能介绍 进百分之十的电池容量,请按电池说明书要求进行定 期均充或每月均充一次。 智能充电机根据电池充电曲线设计,自动检测电池电压 , 任何状态下,只要关断充电机的工作电源,便关机。 电流,保证电池不过充,不欠充,本机一键式操作,无需调 节,全过程智能控制,使用非常方便。 22 23 充电机的保养及注意事项 , 恒流充电:当电池电压较低时,以0.1C-0.14C限流恒流, 充电机的保养: 充电,避免电池充电初期过流充电造成过充现象和保证, 请用于干布或防静电布擦拭以保持充电清洁。 充电机的安全使用时间约6-7H,充时电量80%。 , 切勿使用化学或磨损性清洁剂,以免损伤机壳。 , 恒压充电:当电池电压升高后,自动转为恒压充电,电, 必须防止充电机受强烈震荡或暴露于高温和潮湿的 流自动减小,避免了充电后期电流过大造成电瓶析气失 环境中。 水现象,延长电池寿命。充电电流继续减小到设定值时,, 充电机的注意事项。 黄灯亮,电池基本充足可用,时间约2H,充进电量20%。充, 充电机禁止擅自拆卸分解。 acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership 3-D-120 6 120 12 8 20 10 电过程中若遇停电,再来电,充电机仍能继续保持正常充电。 , 浮充充电:保持恒压充电(2.27V×N,N为2V单体),充 电电流继续减小,对电池进行维护式充电,充电电流减 初充电 小到设定值或充电时间达到设定值时,充足红灯亮,时 , 未经使用的电池在使用前应进行初充电。初充电前应将间约2H,充时电量10%。 电池表面擦拭干净,检查有无损坏;按串联方式组成电, 均衡充电:均充功能:可以消除电池的不均衡现象和对 池组时应紧密无间隙,保证极性正确。螺栓联接时应压陈旧电池及寒冷季节的电池进行补充充电,建议每月均 紧螺栓保证联接可靠。 充一次,或根据电池使用说明书进行定期均充。 , 拧下液孔塞,清除塞内透气孔上密封物保证透气孔畅通;使用方法:当电池充足后,按一均充键,小电流恒流均充二 或拔下密封盖换上掀盖式液孔塞并打开掀盖。 小时自动转为浮充,可充进电量10%。 , 在充电设备能正常工作的条件下将密度为(1.26? 30.005)?/dm(25?)温度小于30?的硫酸电解液灌入电 池,液面高出保护板15-25(?)。此时为了降低电解液因 化学反应而上升的温度让电解液充分渗入极板、隔板孔 隙内; 电池需静置3-4小时,不超过8小时。待液温降至 24 25 ※十七、蓄电池使用维护说明书※ 35?以下方向可进行初充电.(必要时可在冷水槽中降温) 静置后液面下降应补足电解液。 主要规格及技术参数 , 硫酸电解液是符合国家标准GB4554-84的蓄电池硫酸与蓄电池型 额定电5h率额定初充电 普通充电 蒸馏水配制而成,切勿用工业硫酸、自来水代用。电解号 压(V) 容量Ah 液标准(25?)密度按下式进行换算。 ?阶段 ?阶段 ?阶段 ?阶段 D25=DT+0.0007(T-25) 式中:D25:25?时电解液密度。 acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership 3DT:T?时电解液实测密度。 8V电池为6.8V/只),电解液密度降至1.17?/ dm时应停止 T:测量密度时的电解液温度。 放电并及时充电;不得长时间搁置。该种在使用过 , 擦干溅落在电池表面的电解液,将电池组的正、负极分程中需经常进行的补充电称为普通充电。 别与直流电源正、负端相接,接通电源;电源电压应高, 普通充电:根据表中普通充电电流按初充电方法进行,于电池组串联电压的50%,根据表中数据先用第?阶段电充入电量为放出电量的130-140%,充电时间约15小时左流充电,充至电压达到7.2(V/只)(对8V电池为9.6/右。 只)时改用第?阶段电流继续充电。充电过程中电解液, 正常使用的电池应避免过充电,但对下列几种情况的电温度不得超过45?,接近45?时应减半充电电流或暂停 池必须进行适量过充电,即均衡充电。 充电;待液温降至35?以下再继续充电。但需适当延长, 电池组中的“落后电池” ----指充电过程中电压值 充电时间。 低于其它电池的电池及因故障检修过的电池。(均衡, 充足电的依据:在第?阶段“充电”至电压达7.9(V/充电时应将落后电池的正、负极分别与直流电源的只)(对8V电池为10.5V/只),电压变化不大于0.015(V/ 正、负端相接单独进行)。 3只);电解液密度达到1.280?0.005?/dm(25?),2 , 正常使用的电池每2-3个月进行一次均衡充电。 小时内无明显变化并有细密气泡激烈发生时就认为电池 , 长时间没有使用的电池在使用前应进行均衡充电。 已充足电。其充电电量为额定容量的1.5-2倍,充电时 , 均衡充电 间约20小时。 , 以0.1I5A电流进行充电。(I为5小时率容量放电电5, 为了准确控制电解液中硫酸含量,在充电末期应检查各 流)。 电池的电解液密度;如有不符则用蒸馏水或密度为1.40 3 ?/dm的硫酸进行调整,并在充电状态下的2小时内将电 27 26 , 充至电压达到7.5(V/只)(对8V电池为10.0V/只),解液密度与液面调整至规定值。 电液内有气泡发生时减半电流(即0.05IA)继续充5, 初充电结束后将电池表面擦干净,装上液孔塞或闭上掀 电。 盖式液孔塞的掀盖,方可投入使用。 , 充至充足电状态时停充0.5小时再减半电流(即使用和维护 0.025IA)充电1小时。 5, 为保证电池使用寿命,凡投入使用的电池应处于充足电 , 按d条重复数次直至充电机一合闸电池内就有泡激状态;充电不足的电池不可使用。使用过程中应密切注 烈发生时为止。 意放电程度,严禁过量放电----即电压降至5.1V/只(对acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership 保管与贮存 蓄电池应存放在5-40?的清洁、干燥、通风的仓库内,有效贮存期为二年。在贮存期内须按下列要求妥善保管。 , 不受阳光直射,离热源距离不得少于2m。 , 避免与任何液体和有害物质接触,任何金属杂质不得掉 入电池内。 , 不准倒置,不得受任何机械撞击或重压。 , 不允许电池带电解液贮存,特殊情况需带电解液贮存时 应充足电并将电解液的密度与液面高速至规定值。贮存 期满一个月须按普通充电方法进行一次补充电。 28 acceptance of oil tank 3 JB/ T4735-1997 steel welded atmospheric pressure vessel 4 GB50231-2009 mechanical equipment installation engineering construction and acceptance specification for 5 GB50275-98 compressor, fan and pump installation engineering construction and acceptance specification for lifting 6 HG20201-2000 construction installation engineering construction standard 7, HG ... Pressure gauges, using an installed spark arrestor for acetylene cylinders, illegal carrying, using gas cylinders, each operator fined 20 Yuan. Gas bottle without the hot sun exposure measures, responsibilities of team a fine of 50 Yuan. (7) at height and the opening and provisional protective measures have been taken, the responsible unit fined 200 Yuan, construction person in charge a fine of 50 Yuan. (8) no permit to work and the job in accordance with the provisions, on the job unit fined 300 yuan, the unit will charge a fine of 100 Yuan. 7.5.3 accident penalties (1) injuries fatalities directly punished 1~2 million. Direct responsibility for the accident and have the corresponding responsibility of leadership, such as concerning administrative sanctions, should be brought to the company or the relevant Department. (2) personal injury accident occurred, the direct punishment 0.5-10,000 yuan, responsible for the direct responsibility for the accident and the responsibility of leadership, such as concerning administrative sanctions should be dealt with by the personnel Department of the company. (3) personal injury accident occurs, the direct punishment 500-1000, who is directly responsible for the accident responsibility, give notice of criticism and 50-100 economic sanctions against them. (4) to conceal the accident, reported without undue delay or false, to inform the administrative leadership
本文档为【1250-1050扫地机说明书】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑, 图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。
下载需要: 免费 已有0 人下载
最新资料
资料动态
专题动态
is_713593
暂无简介~
格式:doc
大小:201KB
软件:Word
页数:0
分类:生活休闲
上传时间:2018-10-13
浏览量:10