led路灯标准

led路灯 标准 excel标准偏差excel标准偏差函数exl标准差函数国标检验抽样标准表免费下载红头文件格式标准下载 K 73 Record number: DB44 Local standard of Guangdong Province DB44/T XXX - 2009 LED street lamp 2009-XX-XX releases 2009-XX-XX implementation Issued by Guangdong quality and Technical Supervision Bureau DB44/T XXX - 2009 Preface This standard is proposed by Dongguan KingSun Au Optronics Co. This standard is supervised by Bureau of quality and technical supervision of Guangdong province. The standard main drafting unit: Dongguan KingSun Au Optronics Co, Tsinghua University, Dongguan city quality supervision and testing of the measurement. The main drafters of this standard are Li Xuliang, Luo Yi, Qian Keyuan, Zhu Bingzhong, Chen Daqing, Hu Zhengang, Liang Mingjuan, Liao Huaifei, Yao Zhihui, Zhang Zhihai, Deng Guoqiang, Dai Lianghui, Lei Zongping, Zhang Liqiang, Huang Daokang, Fu Baocheng, Erwin, Chen Haihan, Yang, Changjiang, Huang, Weng Wei East, Guo Jiankun, Lao Ying hai. DB44/T XXX - 2009 LED street lamp 1 range This standard defines the LED (LED) street lamp definition, product classification, type and nomenclature, technical requirements, test methods, inspection Rules of inspection and signs, instructions for use, requirements for packaging, transportation and storage, etc.. This standard applies to 250 V under DC power supply or below 1000 V AC power supply, road, street, tunnel lighting and other room grandfather LED (LED) street lamp for common place lighting. This standard is read together with relevant sections of GB 7000.1 and other related standards. 2 normative reference documents The terms in the following documents are referenced by this standard and become the provisions of this standard. Any dated reference document, followed by all of them The amendment (excluding the content of the Corrigendum) or the revised version does not apply to this standard; however, it is encouraged to study in accordance with this standard Do you want to use the latest version of these files?. Any undated reference document whose latest edition is applicable to this standard. GB/T 191 packaging, storage and transportation, graphic signs (GB/T 191 - 2008, ISO, 780:1997, MOD) GB/T 2900.65 Electrotechnical terminology lighting (GB/T 2900.65 - 2004, IEC, 60050-845:1987, MOD) GB 7000.1 - 2007 luminaires - first part: General requirements and tests (GB 7000.1 - 2007, IEC 60598-1:2003, IDT) GB 7000.5 - 2005 road and street lighting safety requirements of luminaires (GB 7000.5 - 2005, IEC60598-13:2002, IDT) General requirements for photometric measurements of GB/T 9468 luminaires The limits for the harmonic current emission limits compatible with GB 17625.1 (electromagnetic equipment input current is less than or equal to 16A) GB/T 17626.5 electromagnetic compatibility test and measurement technology surge impact immunity test electromagnetic compatibility test and measurement technology Surge (impact) immunity test (GB 17626.5 - 2008, IEC, 61000-4-5:2005, IDT) Limits and methods of measurement of radio disturbance characteristics of GB 17743 electrical lighting and similar equipment (GB 17743 - 2007, CISPR 15: 2005, IDT) Control devices for GB 19510.1 lamps - part first: General requirements and safety requirements (GB 19510.1 - 2004, IEC 61347-1: 2003, IDT) CJJ 45 - 2006 urban road lighting design standards SJ/T 11364 electronic information products pollution control labeling requirements IEC 60838-2-2 miscellaneous lampholders - Part 2-2: Particular requirements for connectors for LED modules Control devices for IEC 61347-2-13 lamps - Part 2-13: Safety requirements for LED module controls IEC 62031 safety requirements for LED modules for general lighting The biosafety of IEC 62471 lamp and light system 3 terms and definitions GB/T 2900.65, GB 7000.1, GB 7000.5 and CJJ 45, established and the following terms and definitions apply to this standard. DB44/T XXX - 2009 Three point one LED module (LED, module) Combined lighting source device. In addition to one or more light-emitting diodes (LEDs), further components may be further included, for example Optical, mechanical, electrical and electronic components, but not controls. Three point two LED heat sink (LED, heat-sink) Light emitting diode (LEDs) products are closest to the heat sink of the chip. Three point three LED street lamp (LED street lamp) The utility model relates to a combined lighting lamp meeting the requirements of this standard, comprising a lamp shell, an LED module, a LED module, a control device, and an optical component, Mechanical components, etc.. Three point four Initial value (initial, values) The photoelectric parameters of LED street lamps are measured without aging and burning at 2 h under rated conditions. Three point five Average correlation color temperature (average, CCT) All the light emitted by the LED street lamp in all directions is measured by the associated color temperature after mixing. Three point six The average color rendering index (average, color, rendering, index) All the light emitted by the LED street lamp in all directions is measured by the color rendering index. Three point seven LED street lamp rated maximum temperature Tc (rated, maxium, temperature, of, LED, street, lamp) In the normal working state and at the maximum value of the rated power voltage or the voltage range of the rated power supply, the outer surface of the radiator of the LED street lamp is used Maximum allowable temperature on (if marked, at the indicated part of a mark). 4 product segmentation Classify according to the provisions of the fourth chapter in GB 7000.5 - 2005. 5 model and designation 5.1 product model The type of LED street light sign shall comply with the requirements of 5.2. DB44/T XXX - 2009 5.2 naming methods With the capital Chinese phonetic alphabet, the Arabia numerals and the Rome numerals, the product categories and the main features are shown as follows: - - - - - - - - - / - - - - Class of protection (A - IP67, B - IP66, C - IP65) The light efficiency grades of lamps and lanterns are from high to low, and are indicated by I, II, III and IV. Spot shape (J - rectangle, Y - circle, T - ellipse) Average correlated color temperature (G - 4000, K - 6500 K, D - 2700, K ~ 4000 K) The supply voltage is expressed in figures, in units of V Power supply type, AC is expressed by AC, DC is expressed by DC The rated power of LED street lamps is expressed in figures, in units of W LED street lights, represented by LLD 6. General requirements 6.1 using environmental requirements LED street lights should be able to work in a long, continuous and reliable manner under the following natural conditions: A) outdoor temperature: -25 DEG C to +50 centigrade; (b) monthly average air relative humidity: no more than 90% (25 + 5 DEG C); In operation beyond the above environmental limits, technical requirements shall be agreed upon by the manufacturer and the user. 6.2 design and make LED street lamp design and production shall comply with the requirements of the product in CJJ 45. 7. general technical requirements 7.1 appearance 7.1.1 LED street lamp surface should be no scratch, light inside and outside the body should not endanger the production, transportation, installation and use of personnel sharp corners and burrs. 7.1.2 spraying the surface of color should be uniform, smooth, uniform coating thickness, no sagging, accumulation, show, affect the appearance of wrinkles Defect. 7.1.3 welding parts should be flat and firm, without welding, weld spatter, wear phenomenon. 7.2 security The 7.2.1 LED street lamp should be able to work reliably, normally and regularly at nominal rated power, voltage, and frequency, and for users and rings Environment does not cause harm. The 7.2.2 LED street lamp should comply with the provisions of GB 7000.1 and GB 7000.5. The controls for the 7.2.3 LED street lamp shall comply with the GB19510.1 and the corresponding national standards or IEC 61347-2-13 regulations. The LED module of the 7.2.4 LED street lamp shall comply with the corresponding national standards or IEC 62031 regulations. The connectors for the LED module of the 7.2.5 LED street lamp shall comply with the corresponding national standards or IEC 60838-2-2 regulations. The light biological safety requirements of 7.2.6 LED street lamps should be in line with the corresponding national standards or IEC 62471 regulations. DB44/T XXX - 2009 7.3 electromagnetic compatibility The electromagnetic compatibility requirements of LED street lamps shall comply with the provisions of GB 17743 and GB 17625.1. 8 special technical requirements 8.1 electric performance of lamps When the LED street lamp works under the nominal rated power voltage and rated frequency, the actual power consumption and rated power shall not be greater than the rated power 10%, the power factor should not be less than 0.92. 8.2 protection level LED street lamp protection level a class product should not be lower than IP67; B class products should not be lower than IP66; C class products should not IP65. 8.3 average life The rated average life of LED street lamps should not be less than 30000 H. 8.4 maximum temperature LED street lamp rated maximum temperature Tc shall not be greater than 58 degrees centigrade. 8.5 maximum heat sink temperature The maximum heat sink temperature of each LED tube in the luminaire shall not be greater than 65 degrees centigrade. 8.6 main light parameters Table 1 main parameters of LED street light Ordinal item parameter Grade average CCT 4000K to 6500K Scope of application average CCT 2700K to 4000K Scope of application I = 78 Apply to trunk Road and expressway More than 65 Apply to trunk Road and expressway Initial light efficiency of 1 LED street light Lm/W II = 68 Apply to trunk Road and expressway More than 55 for secondary roads III = 58 Apply to trunk Road and expressway More than 47 for secondary roads IV = 50 Apply to sub dry Avenue More than 40 for secondary roads 2 the average color index Ra = 65 32000 h luminous flux maintenance rate greater than 98% 4 5 000 h 光通量维持率 ?97% 5 光斑形状 矩形 / 圆形 / 椭圆形光斑 6 配光曲线 按cjj 45 - 2006 中4.2 规定 关于下班后关闭电源的规定党章中关于入党时间的规定公务员考核规定下载规定办法文件下载宁波关于闷顶的规定 的使用场合, 选择截光型、半截光型、非截光型或 泛光型 (7) 抗扰度 浪涌抑制性能 (抗雷击) 的电压保护水平应不低于2 kv (线 - 线) 和4 kv (线 - 地). (8) 配光特性 5 db44 / t xxx - 2009 灯具中部分led 灯泡熄灭或整灯调光时, 其光斑形状和路面照度均匀性不应发生明显变化. 9 试验 方法 快递客服问题件处理详细方法山木方法pdf计算方法pdf华与华方法下载八字理论方法下载 9 (1) 外观要求 目测检查 (2) 安全 按gb 7000.1、gb 7000.5、gb19510.1和相应的国家标准或国外标准进行检验. (3) 电磁兼容性 按gb 17743 和gb 17625.1 的相关规定进行. (4) 灯具电性能 在25??2?的环境温度下, 在稳压电源 (与灯具标称频率相同) 及led 路灯之间接入精度不小于 0.5 级的交直流电参数测试仪, 使led 路灯处于正常工作位置, 接通并调节电源电压至额定值 (如灯具 标称电源电压范围, 则分别调节至电源电压范围的最大值和最小值) 使led 灯具工作2 h, 记录功率和 功率因素值. (5) 防护等级 按gb7000.1 的规定进行. (6) 光衰和寿命试验 9.6.1 灯具老化方法 灯具老化在没有强制通风、温度控制在20? - 30?的环境中进行, 灯具按正常安装姿态架设, 按灯 具标称额定电压或标称的适用电压范围的最大电压接通电源, 灯具以满功率工作.灯具在老化过程中, 每24 h 中关闭不少于2 次, 每次关闭时间应为25 min,35 my, 间隔时间至少应为30 min.样品数量 不少于3 台.试验中, 灯具不得出现任何故障、烧毁, 否则不合格. 9.6.2 光衰和寿命测量推算方法 以照度法替代光通量法, 在距离灯具高度2 米处下方测量中心点和沿道路方向的轴线上每距1 米一 个点的水平照度值, 共测5 个点, 与各点初始值对比并得出5 个点的平均维持率值.在2 至5 000 000 h h 之间, 每336 h 间隔测一次平均维持率值; 如5 000 h 时灯具仍然符合要求, 则以2 000 h 时的各点 照度值为初始照度值, 已测得的每336h 间隔的照度值与2000 h 时 对应的初始照度值比较并得出平均维 持率, 由上述10 个点的平均维持率拟合曲线推算出平均维持率为 75% 时的寿命时间加上5000h 即为该 灯具的寿命.选取其中1 只路灯, 同时用光度分布测试法测0h 和 2000h 时的光通量, 计算出2 000h 光通维持率作为校准值.测量照度时, 环境温度应控制在25??1? 稳定3h 以上的情况下进行. (7) 最大温度 按 gb7000.1-2007 中第12 章的规定进行. 9.8 maximum heat sink temperature Select the highest heat sink temperature in LED, and place the thermocouple at the bottom of the LED closest to the bottom. 9.9 main light parameters of lamps and lanterns 9.9.1 average color moderate average color rendering index At ambient temperature, rated voltage and rated frequency at 25 + 1 C, the integral of the lamp sample is measured by integrating spectrum measuring system DB44/T XXX - 2009 In the ball, to avoid direct light into the test probe, the external surface of the lamp should be attached to the white color film which does not affect the color temperature test. Ignition temperature 1 h after test Test. Light efficiency and light distribution curve of 9.9.2 luminaire At the temperature of 25 + 1 C, the system was measured by the photometric distribution test system. Firstly, the luminous flux, luminous intensity distribution and light distribution of the luminaire are tested Curve, etc., the luminous efficiency of the lamp is LED, the ratio of luminous flux of the street lamp to the actual consumption power of the lamp. 9.10 immunity Proceed according to the method specified in GB 17626.5. 10. inspection rules 10.1 inspection and classification Product inspection is divided into factory inspection and type inspection. 10.2 factory inspection 10.2.1 each luminaire should be inspected by the inspection department and issued a certificate of approval before leaving the factory. 10.2.2 factory inspection items see Table 2; for the sampling inspection failed, should be doubled sampling inspection. After reinspection, talent Re packing and delivery unit. If the reinspection fails, the batch shall be disqualified; if any other items fail to be qualified, the batch shall be repaired and inspected You may leave the factory. 10.3 type inspection 10.3.1 type inspection shall be carried out in the following circumstances: A) new products or old products factory production trial design appraisement; (b) after formal production, such as structure, material, and process have changed considerably, which may affect the performance of the product; C) the product has been shut down for more than half a year and resumed production; (d) the factory inspection result is quite different from the last type inspection; E) when the national quality supervision organization proposes the requirements for type inspection. 10.3.2 type inspection samples are extracted from the factory inspection and qualified varieties, and 4 samples are taken each time. If the photoelectric performance of the lamp is unqualified, the sample shall be designated as Unqualified。 In other projects, if there are unqualified items, the samples should be doubled in the same batch of products, and the unqualified items should be re examined and still not qualified, The type test is not qualified. Table 2 inspection items Inspection requirements, test methods, ex factory inspection, type inspection The appearance of 7.1 9.1 tick tick The safety of a 7.2 9.2 tick tick The electromagnetic compatibility of 7.3 V 9.3 The electrical properties of 8.1 V 9.4 V lamps Protection class 8.2 9.5 B. The average life expectancy of 8.3 V 9.6 The maximum temperature of B 8.4 9.7 tick tick The maximum heat sink temperature is 8.5, 9.8 The main optical parameters of 8.6 V 9.9 DB44/T XXX - 2009 Table 2 (Continued) Immunity 8.7 V 9.10 The light distribution characteristics of 8.8 B. Note: the table "V" for inspection items, "--" without inspection items. A factory inspection, safety performance only test insulation resistance and electrical strength. B factory inspection, the same batch of 1 random inspection. 11 signs, product manuals 11.1 signs The product pollution control labeling requirements shall comply with the requirements of SJ/T 11364. Each luminaire shall be properly marked with product labels, and the labels shall comply with the relevant provisions of GB/T 13306. In addition, the product The following contents should also be marked: (a) manufacturer's name and site; (b) product name and model number; (c) product number and date of production; D) main technical parameters; (E) product standard number and relevant certification mark. 11.2 product manual Shall comply with the provisions of GB 9969.1. 12 packing, transportation and storage 12.1 packing 12.1.1 in the product package, should be equipped with the following technical documents (into a waterproof bag): A) packing list; B) product qualification certificate; C) product manual; D) annexes and other relevant documents. 12.1.2 product packaging shall be repackaged if it is opened and still stored. 12.2 transport Lamps and lanterns in the transportation process should prevent violent vibration, impact and keep the packaging intact, transportation process should prevent rain and snow attack protection measures Shi. The graphic sign shall be in accordance with the provisions of GB/T 191. 12.3 storage After the packing of lamps and lanterns, it should be stored in the warehouse of ventilation, dry and non corrosive medium, and there should be no harmful gases and inflammable and explosive materials in the warehouse Articles and corrosive chemicals. The lamp should not be stressed, and should not have strong mechanical vibration, impact and magnetic field. DB44/T XXX - 2009 Compilation of "LED street lamp" I. source of tasks This standard according to the Guangdong quality and Technical Supervision Bureau Guangdong quality supervision standard letter [2008] 25 document project. This standard by Dongguan KingSun Au Optronics Co, Tsinghua University, Dongguan city quality supervision and testing of the measurement, Shenzhen sunshine Fuyuan branch Technology Co. Ltd, Zhongshan city - the source of solar energy science and Technology Co. Ltd., Zhongshan Tianneng Photoelectric Technology Co. Ltd., Zhongshan Xuyang technology lighting Ltd., Foxconn technology group, Fu Precision Industry (Shenzhen) Co., Ltd., Guangdong Ming Polytron Technologies Inc, Dongguan paramount Photoelectric Technology Co., Ltd., Dongguan Guang Hong Electronics Co., Ltd., Dongguan City products Photoelectric Technology Co., Ltd., Dongguan Lok District plastic electronics products have Limited company, Dongguan Branch Lei digital photoelectric technology Co., Ltd. drafting. This standard is proposed by Dongguan KingSun Au Optronics Co. Two, the purpose and principle of compilation LED (LED) is one of the most promising lighting products in the field of lighting. LED is a solid state cold light source with high efficiency, Energy saving, environmental protection, long life, small size, fast response, vibration resistance, easy maintenance and so on. LED lighting was originally used to display lighting, along with technology It has been widely used in indoor and outdoor general lighting, decorative lighting, urban landscape lighting, automobile lights, signal lights, back Lighting and other lighting fields. This standard defines the LED (LED) street lamp definition, product classification, technical requirements, test methods, inspection rules and labels Records, instructions for use, requirements for packaging, transportation and storage, etc.. This standard applies to below 250 V DC power supply or below 1000 V communication LED (LED) street lamp for street lighting, street road, tunnel lighting and other outdoor public places lighting. Therefore, this standard The formulation is very necessary. Three. Compiling instructions This standard is prepared with GB/T1.1 - 2000 "standard guidelines for the first part: the standard structure and writing rules" and GB/T2000.2 2001 "guide for standardization part second: provisions of adoption of international standards". Dongguan KingSun Au Optronics Co in November 28, 2008 in Guangdong city of Dongguan province held the standard drafting team meeting. The meeting will discuss and coordinate the technical requirements, important performance and testing indicators of the "LED street lamp" standard, and solicit the relevant units and experts Standard opinion. At the meeting, representatives of the team discussed the standards, and made some amendments to the content of the standard, after the drafting of units The opinions of the representatives were studied and analyzed, and the standards were revised and improved to form a draft for comments. Data sources in standards: Requirements for light efficiency, light attenuation, life and temperature data in this standard is mainly based on the reference to the Dongguan KingSun Co. Division of 3 years of test and actual measurement results, and then integrate the views of other counterparts in the factory, and then take into account the current development of the objective situation of LED to formulate The. Dongguan KingSun Au Optronics Co held a local standard "LED Street" research in Guangdong Province, Dongguan city in December 15, 2008 DB44/T XXX - 2009 Meeting。 The meeting solicited draft opinions on the "LED street lamp" and listened to the opinions of the units and experts concerned. The delegates discussed the standard at the meeting, Basically agreed on the main content of the standard, some of the content of the proposed changes, after the drafting of the unit on behalf of Italy See are summarized and analyzed. Dongguan KingSun Au Optronics Co held a "LED" of the coordination on the street in January 5, 2008 in Guangdong city of Dongguan province, At the meeting, the experts once again discussed the "LED street lamp", and carried out research and Analysis on the views of the last seminar representatives, and drew up the draft after the meeting The unit has revised and perfected the standards and formed a manuscript reviewer. Four, standard attributes This standard is the recommended standard. This standard is formulated for the first time.