Welding Procedure Specifications焊接工艺规程(WPS)
Company Name
公司名称
江苏海光重工
WPS No.
编号
WPS-11001
版本号
Rev.0
Welding Process(es)
焊接方法
GMAW
Type(s)
自动化程度
Semi-auto
半自动
Supporting PQR No.
依据工艺评定号
PQR-11001
Limitations 限制: This procedure is not qualified for Notch Toughness applications. 此规程不适用于具有冲击要求的焊接
JOINTS 接头 (QW-402)
Joint Design: butt joint Or corner joint
接头型式: 对接或角接
Root Spacing (根部间隙) Details as drawing 详见图纸
Backing衬垫: yes √ no √ 有或无
Backing Material (Type): Weld metal or base metal
衬垫材料(型式): 焊缝金属或母材
■Metal金属 □ Non-fusing Metal非熔金属 □ Nonmetallic非金属□ Other其它
□ Retainers 成型块
Sketches,Production Drawing, Weld Symbols, or Written Description should show the general arrangement of the parts to be welded. Where applicable, the details of weld groove may be specified.
Details as drawing
BASE METALS 母材 (QW-403)
P-No.分类号 / Group No.组号 / to P-No.与分类号 / Group No.组号 / or或
Specification and type/ grade or UNS Number钢号和等级号为 GB/T 3274-2007 Q235
to Specification and type/ grade or UNS Number与钢号和等级号为 GB/T 3274-2007 Q235 or或
Chem. Analysis and Mech. Prop.化学成分和力学性能为 /
to Chem. Analysis and Mech. Prop.与化学成分和力学性能为 /
Base Metal Thickness Range母材厚度范围: Groove 坡口焊缝: 5-200mm Fillet 角焊缝: All 所有
Maximum pass thickness≤1/2in(13mm) (yes) √ (No)
Other 其它: None
FILLET METALS 填充金属 (QW-404)
GMAW
/
Spec. No.(SFA)
标准
excel标准偏差excel标准偏差函数exl标准差函数国标检验抽样标准表免费下载红头文件格式标准下载
号:
NA
AWS No(Class)分类号:
NA
F-No.
注1
A-No.
注1
Size of Filler Metals 填充金属尺寸:
Φ1.0 mm,Φ1.2 mm
Filler metal product form
Solid
Supplemental filler metal
Not Used
合金元素的成分Alloy chemical composition
NA
Weld Metal Thickness Range焊缝金属厚度范围:
Groove 坡口焊缝:
Max 200 mm
Fillet 角焊缝:
All 所有
Electrode-flux(Class) 焊丝-焊剂分类号:
NA
Flux type
NA
Flux Trade Name 焊剂商标名称:
NA
Consumable Insert 熔化嵌条:
NA
Other其它:
注1:常州正阳焊接材料有限公司GB/T8110-2008 JY50-6(ER50-6)
WPS No./Rev.: WPS-11001/Rev.0
POSITIONS 焊接位置 (QW-405)
Position(s) of groove 坡口焊缝位置: All
Welding Progression(Up or Down)焊接方向(向上或向下): Up √ Down /
Position(s) of Fillet 角焊缝位置: All
Other None
PREHEAT 预热 (QW-406)
Preheat Temp. .Min. 最小预热温度: 10℃ Inter pass Temp. Max.最大层间温度: 80℃
Preheat Maintenance 预热保持方式: AS Welding Other None
POSTWELD HEAT TREATMENT 焊后热处理 (QW-407) Not Used
Temperature Range 温度范围: 610℃±15℃ Time Range 保温时间: 3小时h
Other None
GAS 保护气体 (QW-408) GTAW Percent Composition百分比组成
Gas(es)气体 Mixture混合比 Flow Rate流量
Shielding保护气: CO2 & Ar 80% :20% 15-25L/Min
Trailing尾部保护: No 无 NA NA
Backing背部保护: No 无 NA NA
Other None
ELECTRICAL CHARACTERISTICS 电特性 (QW-409)
Weld
Pass(es)
焊道
Process
焊接方法
Filler Metal填充金属
Current电流
Volt Range
电压范围
(V)
Travel Speed
焊接速度范围
(mm/min)
其它
Other
Class
种类
Dia.
直径(mm)
Type Polar.
极性
Amp. Range
电流范围(A)
1
GMAW
ER50-6
1.0
DCEP
180-220
16-24
/
/
2-3
GMAW
ER50-6
1.0
DCEP
180-220
24-28
/
/
others
GMAW
ER50-6
1.2
DCEP
230-280
28-35
/
/
Pulsing Current 脉冲电流: None Heat input(max)最大线能量: NA
Tungsten Electrode Size and Type 钨极尺寸和类型: NA
Mode of Metal Transfer for GMAW 金属过渡方式(GMAW): Globular Transfer 融滴过渡
Electrode Wire feed speed range 送丝速度范围: As required for Amps 根据电流需要
Other NA
TECHNIQUE 焊接技术 (QW-410)
String or Weave Bead 有无摆动: Weave or String 摆或不摆 Orifice or Gas Cup Size 喷嘴尺寸: OD 8-12 mm
Initial and Inter pass Cleaning 打底或层间清理: 任何机械或化学的方式(化学方式不适用于第二道及第三层以后的焊道)
Any mechanical or chemical method (chemical method not apply to the 2nd pass and 3rd layer and after) Method of Back Gouging 背面清理方法: Brushing or Grinding刷理或打磨 Oscillation 摆动方式: NA
Contact Tube to Work Distance 导电嘴至工件距离: 12 to 15mm
Single or Multiple Pass (Per side) 单道焊或多道焊(每侧): single or multiple单道或多道
Single or Multiple Electrodes单丝焊或多丝焊: NA
Electrode spacing 电极间距 NA
Peening 有无锤击: NA
Closed to out chamber:闭室焊到室外焊 NA
Other其它: None 无
Prepared by 编制: Date: Approved by 批准: Date:
Welding Procedure Specifications焊接工艺规程(WPS)
Company Name
公司名称
江苏海光重工
WPS No.
编号
WPS-11002
版本号
Rev.0
Welding Process(es)
焊接方法
FCAW
Type(s)
自动化程度
Semi-auto
半自动
Supporting PQR No.
依据工艺评定号
PQR-11002
Limitations 限制: This procedure is not qualified for Notch Toughness applications. 此规程不适用于具有冲击要求的焊接
JOINTS 接头 (QW-402)
Joint Design: butt joint Or corner joint
接头型式: 对接或角接
Root Spacing (根部间隙) Details as drawing 详见图纸
Backing衬垫: yes √ no √ 有或无
Backing Material (Type): Weld metal or base metal
衬垫材料(型式): 焊缝金属或母材
■Metal金属 □ Non-fusing Metal非熔金属 □ Nonmetallic非金属□ Other其它
□ Retainers 成型块
Sketches,Production Drawing, Weld Symbols, or Written Description should show the general arrangement of the parts to be welded. Where applicable, the details of weld groove may be specified.
Details as drawing
BASE METALS 母材 (QW-403)
P-No.分类号 / Group No.组号 / to P-No.与分类号 / Group No.组号 / or或
Specification and type/ grade or UNS Number钢号和等级号为 GB/T 3274-2007 Q235
to Specification and type/ grade or UNS Number与钢号和等级号为 GB/T 3274-2007 Q235 or或
Chem. Analysis and Mech. Prop.化学成分和力学性能为 /
to Chem. Analysis and Mech. Prop.与化学成分和力学性能为 /
Base Metal Thickness Range母材厚度范围: Groove 坡口焊缝: 5-200mm Fillet 角焊缝: All 所有
Maximum pass thickness≤1/2in(13mm) (yes) √ (No)
Other 其它: None
FILLET METALS 填充金属 (QW-404)
GMAW
/
Spec. No.(SFA) 标准号:
NA
AWS No(Class)分类号:
NA
F-No.
注1
A-No.
注1
Size of Filler Metals 填充金属尺寸:
Φ1.2 mm
Filler metal product form
Solid
Supplemental filler metal
Not Used
合金元素的成分Alloy chemical composition
NA
Weld Metal Thickness Range焊缝金属厚度范围:
Groove 坡口焊缝:
Max 200 mm
Fillet 角焊缝:
All 所有
Electrode-flux(Class) 焊丝-焊剂分类号:
NA
Flux type
NA
Flux Trade Name 焊剂商标名称:
NA
Consumable Insert 熔化嵌条:
NA
Other其它:
注1:常州正阳焊接材料有限公司GB/T10045-2001 E501T-1
WPS No./Rev.: WPS-11002/Rev.0
POSITIONS 焊接位置 (QW-405)
Position(s) of groove 坡口焊缝位置: All
Welding Progression(Up or Down)焊接方向(向上或向下): Up √ Down /
Position(s) of Fillet 角焊缝位置: All
Other None
PREHEAT 预热 (QW-406)
Preheat Temp. .Min. 最小预热温度: 10℃ Inter pass Temp. Max.最大层间温度: 80℃
Preheat Maintenance 预热保持方式: AS Welding Other None
POSTWELD HEAT TREATMENT 焊后热处理 (QW-407) Not Used
Temperature Range 温度范围: 610℃±15℃ Time Range 保温时间: 3小时h
Other None
GAS 保护气体 (QW-408) GTAW Percent Composition百分比组成
Gas(es)气体 Mixture混合比 Flow Rate流量
Shielding保护气: CO2 NA 15-25L/Min
Trailing尾部保护: No 无 NA NA
Backing背部保护: No 无 NA NA
Other None
ELECTRICAL CHARACTERISTICS 电特性 (QW-409)
Weld
Pass(es)
焊道
Process
焊接方法
Filler Metal填充金属
Current电流
Volt Range
电压范围
(V)
Travel Speed
焊接速度范围
(mm/min)
其它
Other
Class
种类
Dia.
直径(mm)
Type Polar.
极性
Amp. Range
电流范围(A)
All
FCAW
E501T-1
1.2
DCEP
250-300
28-35
/
/
/
/
/
/
Pulsing Current 脉冲电流: None Heat input(max)最大线能量: NA
Tungsten Electrode Size and Type 钨极尺寸和类型: NA
Mode of Metal Transfer for GMAW 金属过渡方式(GMAW): Globular Transfer 融滴过渡
Electrode Wire feed speed range 送丝速度范围: As required for Amps 根据电流需要
Other NA
TECHNIQUE 焊接技术 (QW-410)
String or Weave Bead 有无摆动: Weave or String 摆或不摆 Orifice or Gas Cup Size 喷嘴尺寸: OD 8-12 mm
Initial and Inter pass Cleaning 打底或层间清理: 任何机械或化学的方式(化学方式不适用于第二道及第三层以后的焊道)
Any mechanical or chemical method (chemical method not apply to the 2nd pass and 3rd layer and after) Method of Back Gouging 背面清理方法: Brushing or Grinding刷理或打磨 Oscillation 摆动方式: NA
Contact Tube to Work Distance 导电嘴至工件距离: 12 to 15mm
Single or Multiple Pass (Per side) 单道焊或多道焊(每侧): single or multiple单道或多道
Single or Multiple Electrodes单丝焊或多丝焊: NA
Electrode spacing 电极间距 NA
Peening 有无锤击: NA
Closed to out chamber:闭室焊到室外焊 NA
Other其它: None 无
Prepared by 编制: Date: Approved by 批准: Date:
Welding Procedure Specifications焊接工艺规程(WPS)
Company Name
公司名称
江苏海光重工
WPS No.
编号
WPS-11003
版本号
Rev.0
Welding Process(es)
焊接方法
GMAW
Type(s)
自动化程度
Semi-auto
半自动
Supporting PQR No.
依据工艺评定号
PQR-11003
Limitations 限制: This procedure is not qualified for Notch Toughness applications. 此规程不适用于具有冲击要求的焊接
JOINTS 接头 (QW-402)
Joint Design: butt joint Or corner joint
接头型式: 对接或角接
Root Spacing (根部间隙) Details as drawing 详见图纸
Backing衬垫: yes √ no √ 有或无
Backing Material (Type): Weld metal or base metal
衬垫材料(型式): 焊缝金属或母材
■Metal金属 □ Non-fusing Metal非熔金属 □ Nonmetallic非金属□ Other其它
□ Retainers 成型块
Sketches,Production Drawing, Weld Symbols, or Written Description should show the general arrangement of the parts to be welded. Where applicable, the details of weld groove may be specified.
Details as drawing
BASE METALS 母材 (QW-403)
P-No.分类号 / Group No.组号 / to P-No.与分类号 / Group No.组号 / or或
Specification and type/ grade or UNS Number钢号和等级号为 GB/T 3274-2007 Q235
to Specification and type/ grade or UNS Number与钢号和等级号为 GB/T 3274-2007 Q345 or或
Chem. Analysis and Mech. Prop.化学成分和力学性能为 /
to Chem. Analysis and Mech. Prop.与化学成分和力学性能为 /
Base Metal Thickness Range母材厚度范围: Groove 坡口焊缝: 5-200mm Fillet 角焊缝: All 所有
Maximum pass thickness≤1/2in(13mm) (yes) √ (No)
Other 其它: None
FILLET METALS 填充金属 (QW-404)
GMAW
/
Spec. No.(SFA) 标准号:
NA
AWS No(Class)分类号:
NA
F-No.
注1
A-No.
注1
Size of Filler Metals 填充金属尺寸:
Φ1.0 mm,Φ1.2 mm
Filler metal product form
Solid
Supplemental filler metal
Not Used
合金元素的成分Alloy chemical composition
NA
Weld Metal Thickness Range焊缝金属厚度范围:
Groove 坡口焊缝:
Max 200 mm
Fillet 角焊缝:
All 所有
Electrode-flux(Class) 焊丝-焊剂分类号:
NA
Flux type
NA
Flux Trade Name 焊剂商标名称:
NA
Consumable Insert 熔化嵌条:
NA
Other其它:
注1:常州正阳焊接材料有限公司GB/T8110-2008 JY50-6(ER50-6)
WPS No./Rev.: WPS-11003/Rev.0
POSITIONS 焊接位置 (QW-405)
Position(s) of groove 坡口焊缝位置: All
Welding Progression(Up or Down)焊接方向(向上或向下): Up √ Down /
Position(s) of Fillet 角焊缝位置: All
Other None
PREHEAT 预热 (QW-406)
Preheat Temp. .Min. 最小预热温度: 10℃ Inter pass Temp. Max.最大层间温度: 80℃
Preheat Maintenance 预热保持方式: AS Welding Other None
POSTWELD HEAT TREATMENT 焊后热处理 (QW-407) Not Used
Temperature Range 温度范围: 610℃±15℃ Time Range 保温时间: 3小时h
Other None
GAS 保护气体 (QW-408) GTAW Percent Composition百分比组成
Gas(es)气体 Mixture混合比 Flow Rate流量
Shielding保护气: CO2 & Ar 80% :20% 15-25L/Min
Trailing尾部保护: No 无 NA NA
Backing背部保护: No 无 NA NA
Other None
ELECTRICAL CHARACTERISTICS 电特性 (QW-409)
Weld
Pass(es)
焊道
Process
焊接方法
Filler Metal填充金属
Current电流
Volt Range
电压范围
(V)
Travel Speed
焊接速度范围
(mm/min)
其它
Other
Class
种类
Dia.
直径(mm)
Type Polar.
极性
Amp. Range
电流范围(A)
1
GMAW
ER50-6
1.0
DCEP
180-220
16-24
/
/
2-3
GMAW
ER50-6
1.0
DCEP
180-220
24-28
/
/
others
GMAW
ER50-6
1.2
DCEP
230-280
28-35
/
/
Pulsing Current 脉冲电流: None Heat input(max)最大线能量: NA
Tungsten Electrode Size and Type 钨极尺寸和类型: NA
Mode of Metal Transfer for GMAW 金属过渡方式(GMAW): Globular Transfer 融滴过渡
Electrode Wire feed speed range 送丝速度范围: As required for Amps 根据电流需要
Other NA
TECHNIQUE 焊接技术 (QW-410)
String or Weave Bead 有无摆动: Weave or String 摆或不摆 Orifice or Gas Cup Size 喷嘴尺寸: OD 8-12 mm
Initial and Inter pass Cleaning 打底或层间清理: 任何机械或化学的方式(化学方式不适用于第二道及第三层以后的焊道)
Any mechanical or chemical method (chemical method not apply to the 2nd pass and 3rd layer and after) Method of Back Gouging 背面清理方法: Brushing or Grinding刷理或打磨 Oscillation 摆动方式: NA
Contact Tube to Work Distance 导电嘴至工件距离: 12 to 15mm
Single or Multiple Pass (Per side) 单道焊或多道焊(每侧): single or multiple单道或多道
Single or Multiple Electrodes单丝焊或多丝焊: NA
Electrode spacing 电极间距 NA
Peening 有无锤击: NA
Closed to out chamber:闭室焊到室外焊 NA
Other其它: None 无
Prepared by 编制: Date: Approved by 批准: Date:
Welding Procedure Specifications焊接工艺规程(WPS)
Company Name
公司名称
江苏海光重工
WPS No.
编号
WPS-11004
版本号
Rev.0
Welding Process(es)
焊接方法
FCAW
Type(s)
自动化程度
Semi-auto
半自动
Supporting PQR No.
依据工艺评定号
PQR-11004
Limitations 限制: This procedure is not qualified for Notch Toughness applications. 此规程不适用于具有冲击要求的焊接
JOINTS 接头 (QW-402)
Joint Design: butt joint Or corner joint
接头型式: 对接或角接
Root Spacing (根部间隙) Details as drawing 详见图纸
Backing衬垫: yes √ no √ 有或无
Backing Material (Type): Weld metal or base metal
衬垫材料(型式): 焊缝金属或母材
■Metal金属 □ Non-fusing Metal非熔金属 □ Nonmetallic非金属□ Other其它
□ Retainers 成型块
Sketches,Production Drawing, Weld Symbols, or Written Description should show the general arrangement of the parts to be welded. Where applicable, the details of weld groove may be specified.
Details as drawing
BASE METALS 母材 (QW-403)
P-No.分类号 / Group No.组号 / to P-No.与分类号 / Group No.组号 / or或
Specification and type/ grade or UNS Number钢号和等级号为 GB/T 3274-2007 Q235
to Specification and type/ grade or UNS Number与钢号和等级号为 GB/T 3274-2007 Q345 or或
Chem. Analysis and Mech. Prop.化学成分和力学性能为 /
to Chem. Analysis and Mech. Prop.与化学成分和力学性能为 /
Base Metal Thickness Range母材厚度范围: Groove 坡口焊缝: 5-200mm Fillet 角焊缝: All 所有
Maximum pass thickness≤1/2in(13mm) (yes) √ (No)
Other 其它: None
FILLET METALS 填充金属 (QW-404)
GMAW
/
Spec. No.(SFA) 标准号:
NA
AWS No(Class)分类号:
NA
F-No.
注1
A-No.
注1
Size of Filler Metals 填充金属尺寸:
Φ1.2 mm
Filler metal product form
Solid
Supplemental filler metal
Not Used
合金元素的成分Alloy chemical composition
NA
Weld Metal Thickness Range焊缝金属厚度范围:
Groove 坡口焊缝:
Max 200 mm
Fillet 角焊缝:
All 所有
Electrode-flux(Class) 焊丝-焊剂分类号:
NA
Flux type
NA
Flux Trade Name 焊剂商标名称:
NA
Consumable Insert 熔化嵌条:
NA
Other其它:
注1:常州正阳焊接材料有限公司GB/T10045-2001 E501T-1
WPS No./Rev.: WPS-11004/Rev.0
POSITIONS 焊接位置 (QW-405)
Position(s) of groove 坡口焊缝位置: All
Welding Progression(Up or Down)焊接方向(向上或向下): Up √ Down /
Position(s) of Fillet 角焊缝位置: All
Other None
PREHEAT 预热 (QW-406)
Preheat Temp. .Min. 最小预热温度: 10℃ Inter pass Temp. Max.最大层间温度: 80℃
Preheat Maintenance 预热保持方式: AS Welding Other None
POSTWELD HEAT TREATMENT 焊后热处理 (QW-407) Not Used
Temperature Range 温度范围: 610℃±15℃ Time Range 保温时间: 3小时h
Other None
GAS 保护气体 (QW-408) GTAW Percent Composition百分比组成
Gas(es)气体 Mixture混合比 Flow Rate流量
Shielding保护气: CO2 NA 15-25L/Min
Trailing尾部保护: No 无 NA NA
Backing背部保护: No 无 NA NA
Other None
ELECTRICAL CHARACTERISTICS 电特性 (QW-409)
Weld
Pass(es)
焊道
Process
焊接方法
Filler Metal填充金属
Current电流
Volt Range
电压范围
(V)
Travel Speed
焊接速度范围
(mm/min)
其它
Other
Class
种类
Dia.
直径(mm)
Type Polar.
极性
Amp. Range
电流范围(A)
All
FCAW
E501T-1
1.2
DCEP
250-300
28-35
/
/
/
/
/
/
Pulsing Current 脉冲电流: None Heat input(max)最大线能量: NA
Tungsten Electrode Size and Type 钨极尺寸和类型: NA
Mode of Metal Transfer for GMAW 金属过渡方式(GMAW): Globular Transfer 融滴过渡
Electrode Wire feed speed range 送丝速度范围: As required for Amps 根据电流需要
Other NA
TECHNIQUE 焊接技术 (QW-410)
String or Weave Bead 有无摆动: Weave or String 摆或不摆 Orifice or Gas Cup Size 喷嘴尺寸: OD 8-12 mm
Initial and Inter pass Cleaning 打底或层间清理: 任何机械或化学的方式(化学方式不适用于第二道及第三层以后的焊道)
Any mechanical or chemical method (chemical method not apply to the 2nd pass and 3rd layer and after) Method of Back Gouging 背面清理方法: Brushing or Grinding刷理或打磨 Oscillation 摆动方式: NA
Contact Tube to Work Distance 导电嘴至工件距离: 12 to 15mm
Single or Multiple Pass (Per side) 单道焊或多道焊(每侧): single or multiple单道或多道
Single or Multiple Electrodes单丝焊或多丝焊: NA
Electrode spacing 电极间距 NA
Peening 有无锤击: NA
Closed to out chamber:闭室焊到室外焊 NA
Other其它: None 无
Prepared by 编制: Date: Approved by 批准: Date:
Welding Procedure Specifications焊接工艺规程(WPS)
Company Name
公司名称
江苏海光重工
WPS No.
编号
WPS-11005
版本号
Rev.0
Welding Process(es)
焊接方法
GMAW
Type(s)
自动化程度
Semi-auto
半自动
Supporting PQR No.
依据工艺评定号
PQR-11005
Limitations 限制: This procedure is not qualified for Notch Toughness applications. 此规程不适用于具有冲击要求的焊接
JOINTS 接头 (QW-402)
Joint Design: butt joint Or corner joint
接头型式: 对接或角接
Root Spacing (根部间隙) Details as drawing 详见图纸
Backing衬垫: yes √ no √ 有或无
Backing Material (Type): Weld metal or base metal
衬垫材料(型式): 焊缝金属或母材
■Metal金属 □ Non-fusing Metal非熔金属 □ Nonmetallic非金属□ Other其它
□ Retainers 成型块
Sketches,Production Drawing, Weld Symbols, or Written Description should show the general arrangement of the parts to be welded. Where applicable, the details of weld groove may be specified.
Details as drawing
BASE METALS 母材 (QW-403)
P-No.分类号 / Group No.组号 / to P-No.与分类号 / Group No.组号 / or或
Specification and type/ grade or UNS Number钢号和等级号为 GB/T 3274-2007 Q345
to Specification and type/ grade or UNS Number与钢号和等级号为 GB/T 3274-2007 Q345 or或
Chem. Analysis and Mech. Prop.化学成分和力学性能为 /
to Chem. Analysis and Mech. Prop.与化学成分和力学性能为 /
Base Metal Thickness Range母材厚度范围: Groove 坡口焊缝: 5-200mm Fillet 角焊缝: All 所有
Maximum pass thickness≤1/2in(13mm) (yes) √ (No)
Other 其它: None
FILLET METALS 填充金属 (QW-404)
GMAW
/
Spec. No.(SFA) 标准号:
NA
AWS No(Class)分类号:
NA
F-No.
注1
A-No.
注1
Size of Filler Metals 填充金属尺寸:
Φ1.0 mm,Φ1.2 mm
Filler metal product form
Solid
Supplemental filler metal
Not Used
合金元素的成分Alloy chemical composition
NA
Weld Metal Thickness Range焊缝金属厚度范围:
Groove 坡口焊缝:
Max 200 mm
Fillet 角焊缝:
All 所有
Electrode-flux(Class) 焊丝-焊剂分类号:
NA
Flux type
NA
Flux Trade Name 焊剂商标名称:
NA
Consumable Insert 熔化嵌条:
NA
Other其它:
注1:常州正阳焊接材料有限公司GB/T8110-2008 JY50-6(ER50-6)
WPS No./Rev.: WPS-11005/Rev.0
POSITIONS 焊接位置 (QW-405)
Position(s) of groove 坡口焊缝位置: All
Welding Progression(Up or Down)焊接方向(向上或向下): Up √ Down /
Position(s) of Fillet 角焊缝位置: All
Other None
PREHEAT 预热 (QW-406)
Preheat Temp. .Min. 最小预热温度: 10℃ Inter pass Temp. Max.最大层间温度: 80℃
Preheat Maintenance 预热保持方式: AS Welding Other None
POSTWELD HEAT TREATMENT 焊后热处理 (QW-407) Not Used
Temperature Range 温度范围: 610℃±15℃ Time Range 保温时间: 3小时h
Other None
GAS 保护气体 (QW-408) GTAW Percent Composition百分比组成
Gas(es)气体 Mixture混合比 Flow Rate流量
Shielding保护气: CO2 & Ar 80% :20% 15-25L/Min
Trailing尾部保护: No 无 NA NA
Backing背部保护: No 无 NA NA
Other None
ELECTRICAL CHARACTERISTICS 电特性 (QW-409)
Weld
Pass(es)
焊道
Process
焊接方法
Filler Metal填充金属
Current电流
Volt Range
电压范围
(V)
Travel Speed
焊接速度范围
(mm/min)
其它
Other
Class
种类
Dia.
直径(mm)
Type Polar.
极性
Amp. Range
电流范围(A)
1
GMAW
ER50-6
1.0
DCEP
180-220
16-24
/
/
2-3
GMAW
ER50-6
1.0
DCEP
180-220
24-28
/
/
others
GMAW
ER50-6
1.2
DCEP
230-280
28-35
/
/
Pulsing Current 脉冲电流: None Heat input(max)最大线能量: NA
Tungsten Electrode Size and Type 钨极尺寸和类型: NA
Mode of Metal Transfer for GMAW 金属过渡方式(GMAW): Globular Transfer 融滴过渡
Electrode Wire feed speed range 送丝速度范围: As required for Amps 根据电流需要
Other NA
TECHNIQUE 焊接技术 (QW-410)
String or Weave Bead 有无摆动: Weave or String 摆或不摆 Orifice or Gas Cup Size 喷嘴尺寸: OD 8-12 mm
Initial and Inter pass Cleaning 打底或层间清理: 任何机械或化学的方式(化学方式不适用于第二道及第三层以后的焊道)
Any mechanical or chemical method (chemical method not apply to the 2nd pass and 3rd layer and after) Method of Back Gouging 背面清理方法: Brushing or Grinding刷理或打磨 Oscillation 摆动方式: NA
Contact Tube to Work Distance 导电嘴至工件距离: 12 to 15mm
Single or Multiple Pass (Per side) 单道焊或多道焊(每侧): single or multiple单道或多道
Single or Multiple Electrodes单丝焊或多丝焊: NA
Electrode spacing 电极间距 NA
Peening 有无锤击: NA
Closed to out chamber:闭室焊到室外焊 NA
Other其它: None 无