h November 28, 1995
ELECTRONIC COMPONE
GROUP SHARP CORPORATION
F \
DEVICE SPECIFICATION FOR Business dealing name
PHOTOCOUPLER
MODEL No.
PC817
SPECIFICATION OPTO-ELECTS DEVICES DIV.
1. These specification sheets include the contents under the copyright of Sharp Corporation (“Sharp”].
Please keep them with reasonable care as important information. Please don’t reproduce
or cause anyone reproduce them without Sharp’s consent.
2. Please obey the instructions mentioned below for actual use of this device.
SHARP takes no responsibility for damage caused by improper use of the devices.
(I) This device is designed for general electronic equipment.
Main uses of this device are as follows;
[
* Computer - OA equipment - Telecommunication equipment (Terminal)
- Measuring equipment l Tooling machine - AV equipment l Home appliance, etc. 1
(2) Please take proper steps in order to maintain reliability and safety, in case this device
is used for the uses mentioned below which require high reliability.
-
[
Unit concerning control and safety of a vehicle (air plane, train, automobile etc.)
- Traffic signal * Gas leak detection breaker * Fire box and burglar alarm box
* Other safety equipment, etc. 1
(3) Please do not use for the uses mentioned below which require extremely high reliability.
- Space equipment
[
* Telecommunication equipment (Trunk)
* Nuclear control equipment * Medical equipment etc. 1
Contact a SHARP representative of sales office in advance when you intend to use S?%4.RP
devices for any applications other than those applications for general electronic equipment
recommend by SHARP at (1).
CUSTOMER’S APPROVAL
DATE
PRESENTED
BY
DATE
BY
T. Matsumura,
Department General Manager of
Engineering Dept.,11
Opto-Electronic Devices Div.
ELECOM Group
SHARP CORPORATION
SHARP CORPORATION 1 i November 28. 1995 1
1. Application
This specification applies to the outline and characteristics of photocoupler
Model No. PC8 17series.
2. Outline
Refer to the attached drawing No. CY7073K02.
3. Ratings and characteristics
Refer to the attached sheet, page 3 to 6.
4. Reliability
Refer to the attached sheet, page 7.
5. Incoming inspection
Refer to the attached sheet, page 8.
6. Supplement
6.1 Isolation voltage shall be measured in the following method.
(11 Short between anode to cathode on the primary side and between collector
to emitter on the secondary side.
(21 The dielectric withstand tester with zero-cross circuit shall be used.
(3) The wave form of applied voltage shall be a sine wave.
(It is recommended that the isolation voltage be measured in insulation oil.)
SHARP CORPORATION
6.2 Business dealing name
(” 0” mark indicates business dealing name of ordered product)
Ordered Business Rank mark Ic (mA)
nroduct dealingname
0 PC817Xl A, B, C, D or no mark 2.5 to 30
PC817XIl A 4.0 to 8.0
PC8 17XI2 B . 6.5 to 13
PC8 17XI3 C 10to20
PC8 17XI4 D
PC817XI5 AorB
PC8 17Xi6 B or C
15 to 30
4.0to 13 :
6.5 to 20
I I
1 PC817XI7 1 C or D
1
10 to 30
PC8 172U8
PC8 17XI9
A, B or C
B, CorD
4.0 to 20
6.5 to 30 I I
1 PC817XIO 1 A, B, C or D 1 4.oto30
6.3 This Model is approved by UL.
Approved Model No. : PC8 17
UL file No. : E64380
6.4 This product is not designed against irradiation.
This product is assembled with electrical input and output.
This product incorporates non-coherent light emitting diode.
Test
conditions
1,=5mA
vc,=5v
Ta=25’C
7. Notes
Refer to the attached sheet- 1 - 1, 2.
Ta=25”C
l 1 Forward current
Collector current Ic 50 mA
*l Collector power dissipation PC 150 mW
*l Total power dissipation Ptot 200 mW
*3 Isolation voltage viso 5 kVrms
Operating temperature Topr -30 to +lOO ‘C
Storage temperature Tstg -55 to +125 “C
*4 Soldering temperature Tsol 260 “C
‘1 The derating factors of absolute maximum ratings due to ambient temperature
are shown in Fig. 1 to 4.
*2 Pulse width_IlOO ,us, Duty ratio : 0.001 (Refer to Fig. 5)
*3 AC for 1 min, 40 to 6O%RH
l 4 For 10s
SHARP CORPORATION
3.2 Electra-optical characteristics
r
Input
output
Transfer
charac-
teristics
Parameter Syllhl Condition MIN. TYP. MAX. Unit
Forward voltage VF IFI,=20mA 1.2 1.4 v
Peak forward voltage vFM Im=0.5A 3.0 v
Reverse current 1, v,=4v 10 PA
-
Terminal capacitance Ct v=o, f=lkHz 30 250 pF
Dark current kE0 vc,=20v, IF=0 :- - 100 nA
Collector-emitter BvCEO Ic=O. 1mA 35 - - V
breakdown voltage IF.=0
Emitter-collector BvECO I,=10 /LA, I,=0 6 - - V
breakdown voltage
Collector current
Collector-emitter
saturation voltage
Isolation resistance
Ic I,=5mA.VcE=5V 2.5 - 30 mA
V CEfsat) 1,=2omA 0.1 0.2 v
Ic=lmA
R IS0 DC500V 5XlO’O 1o’l - Q
40 to 6O%FW
Floating capacitance cf
Cut-off frequency fc
v=o, f=lMHz
vc,=5v, Ic=2mA -
R,=lOO R, -3dB
0.6 1.0 pF
80 - kHz
Rise time
Fall time
tr vc,=2v 4 18 pus
Ic=2mA
lf R,=lOO R 3 18 pus
Rank mark
mark l 2
i 6. 5’0.5 1
7. 62ro- 3
1
Pin Nos. and internal
cdnnection diagram
d
2
d
T
1. oy
10. oz.
1.
5 1
l-J 2. 54 $0.25
UNIT: l/l mm
l 2) Factory identification mark shall be or shall not be marked.
PC817
SHARP CORPORRTION
(Fig. 1) Forward current vs.
ambient temperature
-30 0 25 55 75 100 125
Ambient temperature Ta ( “C )
(Fig. 3) Collector power dissipation
vs. ambient temperature
-30 0 25 50 75 100 125
Ambient temperature Ta ( ‘C )
(Fig. 5) Peak forward current
z
.5
vs. duty ratio
2 2000
1000
i 500
2 200
; 100
m” 50
z 2 20
Y 10
2 5 lo-‘2 5 lo”2 5 lo-‘2 5 10”
e Duty ratio
(Fig. 2) Diode power diss&iok<->,
vs. ambient temperature -..
5 80
2 70
.+
i
60
P
t; 40
3
&
4 20
-30 0 25 55 75 100 125
Ambient temperature Ta ( ‘C )
(Fig. 4) Total power dissipation
vs. ambient temperature
r -30 0 25 50 75 100 125
Ambient temperature Ta (‘C )
PulsewidthS ps
Ta=25’C
J
SHARP CORPORATION
4. Reliability
The reliability of products shall be satisfied with items listed below.
Confidence level : 90%
LTPD: 10%/20%
Test Items Test Conditions
$1
Solderability “2
Soldering heat
Terminal strength
(Tension)
Terminal strength
(Bending) *3
Mechanical shock
23O”C, 5 s
260°C. 10 s
Weight : 5N
5 s/each terminal
Weight : 2.5N
2 times /each terminal
15000m/s2, 0.5ms
3 times/ tX, +Y, fZ direction
Variable frequency
vibration
100 to 2000 to 1ooHz/4min
200m/s2
4 times/ X, Y, 2 direction
Temperature 1 cycle -55 ‘C to t 125°C
cycling (30mir-i) (30mi.n)
20 cycles test
High temp. and high +6O’C, 9O%RH, lOOOh
humidity storage
High temp. storage +125”C, lOOOh
Low temp. storage -55”C, 1 OOOh
Operation life I,=SOmA, Ptot=200mW
Ta=25”C, 1 OOOh
*l Test method, conforms to JIS C 7021.
Failure Judgement
Criteria
U
v,>ux 1.2
I,>UXZ
Icso >‘ux2
rc ’ ’ ’ O2
Upper
specification
limit
L : Lower
specification
limit
‘2 Solder shall adhere at the area of 95% or more of immersed portion of
lead and pin hole or other holes shall not be concentrated on one portion.
Samples (nl
Defective(C)
n=ll, C=O
n=ll, C=O
n=ll, C=O
n=ll, C=O
n=ll, C=O
n=ll, C=O
n=22,C=O
n=22,C=O
n=22 ,C=O
i-i=22 ,C=O
n=22.C=0
*3 Terminal bending direction is shown below.
5. Incoming inspection
5.1 Inspection items
(11 Electrical characteristics
V,, I,, I,,, VCE:(satj, Ic, R,,, Visa
(2) Appearance
5.2 Sampling method and Inspection level
A single sampling plan, normal inspection level II based on
IS0 2859 is applied. The AQL according to the inspection
items axe shown below.
Defect Inspection item AQL (%)
-
SHARP CORPORATION
1 For cleaning
SHflRP CORPORATION
Precautions for Photocouplers
(1) Solvent cleaning : Solvent temperature 45°C or less
Immersion for 3 min or less
(2) Ultrasonic cleaning : The affect to device by ultrasonic cleaning is different
by cleaning bath size, ultrasonic power
output, cleaning time, PWB size or device mounting
condition etc. Please test it in actual using condition
and con&m that doesn’t occur any defect before starting
the ultrasonic cleaning.
Applicable solvent : Ethyl alcohol, Methyl alcohol
Freon TE * TF. DifIon-solvent S3-E
Please refrain form using Chloro Fluoro Carbon type solvent to clean
device as much as possible since it is internationally restricted to protect
the ozonosphere. Before you use alternative solvent you are requested
to confirm that it does not attack package resin.
2. The LED used in the Photocoupler generally decreases the light emission power
by operation. In case of long operation time, please design the circuit with considering
the degradation of the light emission power of the LED. (50% / 5years)
( 11 If solder refIow :
It is recommended that only one soldering be done at the temperature
and the time within the temperature profile as shown in the figure.
230t
200°C
180°C
25°C
I -
3. Precaution for Soldering Photocoupler
(2) Other precautions
An infbared Iamp used to heat up for soldering may cause a localized
temperature rise in the resin. So keep the package temperature within
that specified in Item (1). Also avoid immersing the resin part in the solder.
SHflRP CORPORRTION
本文档为【PC817光电耦合器】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑,
图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。