某某公司产品确认规格书

产  品  规  格  书 关于书的成语关于读书的排比句社区图书漂流公约怎么写关于读书的小报汉书pdf SPECIFICATION FOR APPROVAL 产品型号 GIE0118B 版本 A 产品结构 5” G+G 产品类型 电容式触摸屏 制作人（Prepared by） 设计 领导形象设计圆作业设计ao工艺污水处理厂设计附属工程施工组织设计清扫机器人结构设计 部审核 （Checked by） 品管部审核 （Checked by） 总经办批准 （Approved by）                 请客户仔细阅读规格书中的各项内容，当对规格书内各项内容表示认可时；请在下面客户确认项中签字（此规格书为一式两份）。 Please read the following carefully the contents of the customer, the customer said after the signing of the cover on the confirmation of the customer to acknowledge the contents. 客户确认 确认人 (Confirmed by) 设计部审核 (Checked by) 品管部审核 (Checked by) 批准 (Approved by)                 变更记录表 序号 版本号 修改人 修改内容概要 批准 生效日期 1 A 陈小艳 初次发行     2           3           4           5                       目 录 1  工程图 Engineering Drawing ······················································ 2  产品结构 Construction································································· 3  机械特性 Mechanical Characteristics········································· 4  电气特性 Electrical Characteristics············································· 5  光学特性 Optical Characteristics················································· 6  使用环境 Processing Environment·············································· 7  引脚定义 PIN Assignment·························································· 8  驱动IC Controller IC································································· 9  机械测试 Mechanical Test·························································· 10  寿命测试 Life Test······································································ 11  环境测试 Environment Test························································· 12  检验 标准 excel标准偏差excel标准偏差函数exl标准差函数国标检验抽样标准表免费下载红头文件格式标准下载 Inspection Standard······················································ 13  包装及运输 Package&Transport·················································· 14  注意事项 Attention····································································· 15  质量保证 Guarantee························································· 1 工程图 Engineering Drawing 2产品结构 Construction 结构 Construction 所用 材料 关于××同志的政审材料调查表环保先进个人材料国家普通话测试材料农民专业合作社注销四查四问剖析材料 Materials Used 注释 Comment 镜片 COVER LENS 玻璃 GLASS 厚度：0.70mm Thickness：0.70mm 透明胶 OCA 粘胶 Adhesive 厚度：0.175 mm Thickness：0.175mm ITO Sensor ITO Sensor 厚度：0.55 mm Thickness：0.55 mm       3 机械特性 Mechanical Characteristics 项目 Item 描述 Description 单位 Unit 外形尺寸 Outside Dimension 140±0.1 ×81.8±0.1 mm 可视区 View Area 113.12×71.51 mm2 动作区 Active Area 107.6×64.8 mm2 产品厚度 Thickness 1.45±0.1 mm 输入方式 Input Method 手指或者导电笔触 Finger Or Conductive Pen   表面硬度 Hardness Of Surface 表面防刮伤 Hard Surface : >6H [ JIS K 5400 ]   精确度 Accuracy +/-1mm@10mm mm 支持操作 Support Operation 指 Finger 2指 屏体通道数 Channel 17*10   分辨率 Resolution 480*800   接口定义 Interface I2C   支持操作系统 Supported Operating Systems Android2.0-2.3,Window7         4 电气特性 Electrical Characteristics 项目 Item 描述 Description 单位 Unit 工作电压 Operating Voltage DC 1.8 V V 绝缘阻抗 Insulation Resistance ＞20MΩ At DC 25V MΩ 绝缘稳定性 Insulation Ability ≥60sec. At DC 25V sec 响应时间 Chatting Times <5ms ms       5 光学特性 Optical Characteristics 项目 Item 描述 Description 全光透光率 Total Transmittance ＞82% [JISK7105] 雾度 Total Haze <3% [JISK7105]     6 使用环境 Processing Environment 项目 Item 描述 Description 工作温度 Operating Temperature -10℃～+60℃ 工作湿度 Operating Humidity ≤90%RH 储存温度 Storage Temperature -20℃～+70℃ 储存湿度 Storage Humidity <90%RH     7 引脚定义 PIN Assignment 引脚 PIN 信号 Signal 描述 Description 1 VDD Supply Voltage 2 SCL I2C Serial Clock Input. 3 SDA I2C Serial Data Input And Output. 4 INT An interrupt signal to inform the host processor that touch data is ready for read 5 WAKE   6 GND Ground       8 驱动IC Controller IC 9 机械测试 Mechanical Test 1 钢球跌落测试Ball Drop Test (1) 作业环境：温度：22±3℃、湿度：60±10％RH、Level：等级1000 Operating Environment:Temperature:22±3℃、Humidity:60±10％RH、Level : Class1000 (2) 测试 方法 快递客服问题件处理详细方法山木方法pdf计算方法pdf华与华方法下载八字理论方法下载 ：用直径为9mm钢球从30cm高度跌落产品中心，产品不会破裂为合格。 Test Method: With a diameter of 9mm ball falling from 30cm height to Product Center, the product will not break as qualified. 2 静压测试Static Press Test (1) 作业环境：温度：22±3℃、湿度：60±10％RH、Level：等级1000 Operating Environment:Temperature:22±3℃、Humidity:60±10％RH、Level:Class1000 (2) 测试方法：在产品表面放置一个直径为12.7mm橡胶头，产品功能无问题，无破损。 Test Method: Product placed on the surface with a diameter of 12.7mm rubber head, Function is ok, no damage. 3 FPC压合测试FPC Bending Test (1) 作业环境：温度：22±3℃、湿度：60±10％RH、Level：等级1000 Operating Environment:Temperature:22±3℃、Humidity:60±10％RH、Level:Class1000    (2) 测试方法：产品测试后满足电气性能。 Test Method: Meet electrical spec after testing. 1.测试角度Bending Degree:135°; 2.测试半径Bending Radius: R1.0 mm; 3.测试次数Bending Times: 50 Times; 4.测试重量Load: 500g. 4 FPC插拔测试FPC Insert/Pull Out Test: (1) 作业环境：温度：22±3℃、湿度：60±10％RH、 Level：等级1000 Operating Environment:Temperature:22±3℃、Humidity:60±10％RH、Level:Class1000 (2) 测试方法：Test Method: A.测试前确认电性特性符合规格； Before Test: Electrical Characteristic Test is OK. B.测试步骤：开卡锁连接器→插入FPC→锁住FPC→开卡锁连接器→插入FPC→锁住FPC，重复10次； Test Circle: Connector Unlock →FPC Insert →Connector Lock →Connector Unlock →FPC Pull Out →Connector Lock, cycle 10 Times; C.测试后再次确认电性特性符合规格. After Test: Electrical Characteristic Test is OK; 10 寿命测试 Life Test (1)作业环境：温度：22±3℃、湿度：60±10％RH、 Level：等级1000 Operating Environment:Temperature:22±3℃、Humidity:60±10％RH、Level:Class1000 项目 Item 规格 Specification 条件 Condition 打点寿命 Input Life 250g×3500万次 35,000,000 Times 功能OK，外观轻微划伤OK。 The function is ok。 笔写寿命 Notes Life 250g×10万次 100,000 Times 功能OK，外观轻微划伤OK。 The function is ok。       11 环境测试 Environment Test (1)高温测试 High temperature：+80℃，120 hr. (2)低温测试 Low temperature：-20℃，120 hr. (3)高温高湿测试 High temp./high humidity test：60℃&90%RH 120 hr. (4)高低温测试 High Low temperature test：-20℃ 30min/+70℃ 30min, 60%RH 24hr，this is a Cycle, continued 24hr test. (Including heating and cooling of 30 minutes) 将产品从测试机内取出，在室温放置24小时后才能进行测试，功能无异常。 Remove the product from the testing machine, at room temperature for 24 hours before testing, function is OK.. 12 检验标准 Inspection Standard 1 检验条件Inspection conditions： 1.1 检查距离：距离产品250-300mm Inspection distance: Inspect 250-300 mm away from the sample. 1.2 检查角度：45度，6点钟方向（所有的不良项目在此方向和角度需要被检查出来）。 Inspection angle: 45 degrees in 6 o’clock direction (all defects in viewing area should be inspected from this direction)，Rotate 30o about the vertical axis 1.3 环境温度为：20-30度 Temperature: 25±5 oC 1.4 光源高度：D65 800-1200 Lux Light source: D65 1000 Lux +/- 20% 2 检验项目Inspection Items： 项目 Items 图片 Picture 类型Type 标准 Standard 判定Judgment 备注 Remarks 玻璃 破损 The Glass is damaged 拐角 破损 It's damaged to turn Cape Ma X≤1.5mm 合格 Accept 在不影响功能的前提下Without affecting the function of the premise Y≤1.5mm 合格 Accept Z≦1/2T 合格 Accept 除转角以外任何范围的破损In addition to turning Cape any breakage of scope corner Mi X≤2.0mm 合格 Accept 在不影响功能的前提下 Without affecting the function of the premise Ma Y≤2.0mm 合格 Accept Z≦1/2T 合格 Accept 玻璃破裂 Broken Glass   Cr 产品任何部 位存在破裂 Product any part exists broken 不合格 Failure   13 包装及运输 Package and Transport 1 包装 Package 不可有脏东西附着，使用泡沫盒材质包装。 Can not have dirt attached, use foam box packing material. 2 输送Transport 避免产品直接暴露在阳光直射或高温高湿的环境下运输。 Avoid direct exposure to sunlight or high temperatures and humidity environment transport. 14  注意事项 Attention 项目 Project 注意事项 Notes 储藏 Store (1)按照本规格书中保存温度范围要求储藏产品。 In accordance with the specifications required storage temperature range of book preservation products. (2)储藏时请保证产品包装完好。 Please ensure the product packaging when stored in good condition. (3)避免阳光直射产品。 Avoid direct sunlight product. (4)尽量避免产品接触水、有机溶剂、酸性物质和硫酸化合物等。To avoid product contact with water, organic solvents, acid and sulfuric acid compounds. 拆包装 Unpacking (1)请勿通过抓住 FPC 来取放产品。 Do not grasp the FPC to take place through the product. (2)按照包装箱上的"上/下"标记方向打开产品包装。 According to the box on the "Over / under" Mark the direction of opening the product packaging. 操作 Operating (1)输入时应使用手指或专用笔。 Input should use your fingers or pens. (2)不可用力拉扯 FPC，以免造成产品内部电气连接不良；不可扭曲和弯折 FPC 输出端，以免造成 FPC 与控制器的连接不良。 Can not pull hard FPC, to avoid bad electrical connection inside the product; not twisted and bent FPC output, so as to avoid adverse FPC connection to the controller. (3)不可弯折和分解本品。 Can not bend and break the product. (4)不要在产品的动作区域滴上水滴，以免引起误操作。 Do not drop the product of the action on the drop zone, in order to avoid misuse. 上机 Installed (1)请勿在触摸屏上施加过大压力而造成产品损伤。 Does not touch too much pressure is applied to the product cause injury. (2)整机设计时，请避免损伤 FPC 及呈锐角状弯折 FPC。 Machine design; avoid injury and acute angle-shaped bend FPC FPC. (3)请勿在 FPC 与屏连接部施加过大压力，导致屏体内部电气连接不稳定。 Do not connect the FPC and the department of screen put too much pressure, leading to screen the internal electrical connection is unstable. (4)组装时避免工具损伤产品。 Assembly of the product to avoid tool damage. (5)装机中尽量避免静电产生。Try to avoid static electricity installed.     15 质量保证 Guarantee 1  本条款适用于深圳北泰显示技术有限公司生产的所有产品。 The provision applies to all the products made by Shenzhen Beitai Display Co, Ltd. 2  北泰公司对条款适用内的产品于购买日起，提供壹年（1年）的质量保证期，如在质量保证期内 是我司责任的不良品，我司将负责返修或更换。 Beitai Company supplies quality guarantee of 1 year since the day of product purchase, and we would either repair or replace the bad products if they are unqualified from the beginning. 3  以下情况不在我司保证范围之内，我司不给予返修或更换。具体如下： Our company would not repair or replace the products of the following conditions, which is out of guarantee scope;    3.1产品交付客户后，因跌落或撞击或不当操作造成的不良品； Products damaged by falling, impacting or improper operation after delivering to customers; 3.2因为自然灾害造成的不良品；Products damaged by natural disaster; 3.3在未经我司同意之前，客户私自进行再加工处理的产品； Products processed by customers without any permission of our company; 3.4客户未按注意事项作业而造成的不良品。 Products damaged by customers whoever conducts the operation without complying with the instructions. 4  本确认书经客户承认后，客户不得有所变更，如需变更，需双方友好协商好重新出确认书认可，否则一切损失由贵公司负责。 The customer should not change the Confirmation Document after approved by the customer. If the change is necessary, the two parties should make a new Confirmation Document for approval through negotiation friendly; otherwise, any caused loss should be beard by the company.