Product Specification
Cartons/Packaging Test Standard
Issue date: Jun 7, 04 Revision date: Page 1 of 4
Document EN111
1.0 Introduction
All products to be shipped to Salton groups of company should pass package test,
which based on standard of International Safe Transit Association (ISTA). Depending
on the nature and weight of goods ISTA-1A, ISTA-1B, ISTA-2A or ISTA-2B procedure
would be used. Please refer to Salton’s Vendor Manual for classification. The following
paragraphs determine each procedure in detail according to ISTA requirement. After
either ISTA-2A or ISTA-1A procedure, Hi-pot test, Leakage current test and Power
input test will be done to verify any damage to the product as well.
2.0 Scope
These packaging requirements cover all products including but not limited to electrical
appearance, hard goods, glass, ceramic, extra larger goods for export by surface.
3.0 Testing
3.1 ISTA-2A procedure
ISTA -2A covers testing of individual packaged-products weighting 150pounds or less
for surface shipment. There have 4 tests within ISTA-2A, which is conditioning test,
compression test, 1st vibration test, drop test/shock test and 2nd Vibration test.
3.1.1 Conditioning
Sample would be stored at 38 ±к 2к, relatively humidity 85%±5% for 72 hours,
then stored at 60 ±к 2к, relatively humidity 30%±5% for 6hours by using
conditioning machine comply with ISTA requirement
Anticipated
conditions
Time in Hours Temperature
in ±к 2к
Humidity in %
Tropical (Wet)
Then desert
(Dry):
72
then 6
38к
then 60к
85%RH±5%
then 30%RH ±5%
3.1.2 Compression
Add a compression load on the sample for ONE hour. By using weight DW,
and by using compression machine complied with ISTA requirement.
DW=Wt x (S-1) x F
Wt=Total weight of the packaged-product
S=Total number of packaged-products in a stack
1=Represents the bottom container in a Stack
F=Compensating factor ,F=4
S=6.9m÷H
H=Height of one packaged-product in meter
DW=test load for apply and hold.
3.1.3 Vibration
Fixed displacement non-linear motion Vibrate the sample at X cycle per
minutes (CPM) for time t (test duration in minutes)/2 what the determination
of CPM should according to First Vibration test Block step 3 to 7 of ISTA-2A
Product Specification
Cartons/Packaging Test Standard
Issue date: Jun 7, 04 Revision date: Page 2 of 4
Document EN111
Time t =14,2000 vibratory impacts ÷Cycles Per Minute(CPM)
Rotate the sample to 90º if possible otherwise rotate 180º and repeat the
above step.
3.1.4 Inspection
Inspection of the package-product for visible damage is allowed, provided
inspection does not alter, in any way, the current condition of the package or the
condition or position of the product (s).
3.1.5 Drop test
Drop the sample at height H. according to sequence in table.
Product Specification
Cartons/Packaging Test Standard
Issue date: Jun 7, 04 Revision date: Page 3 of 4
Document EN111
3.1.6 2nd Vibration test
Repeat 1st Vibration test
3.1.7 Inspection
Inspection of the package-product for visible damage is allowed, provided
inspection does not alter, in any way, the current condition of the package or the
condition or position of the product (s).
3.2 ISTA-1A procedure
ISTA -1A covers testing of individual packaged-products weighting 150pounds or less for
surface shipment. There have 2 tests within ISTA-1A, which is vibration test, drop
test/shock test .
3.2.1 Vibration
Fixed displacement non-linear motion Vibrate the sample at X cycle per minutes
(CPM) for time t (test duration in minutes)/2 what the determination of CPM
should according to First Vibration test Block step 3 to 7 of ISTA-2A
Time t =14,2000 vibratory impacts ÷Cycles Per Minute(CPM)
Rotate the sample to 90º if possible otherwise rotate 180º and repeat the above
step.
3.2.2 Inspection
Inspection of the package-product for visible damage is allowed, provided
inspection does not alter, in any way, the current condition of the package or the
condition or position of the product (s).
3.2.3 Drop test
Drop the sample at height H. according to sequence in table.
3.2.4 Inspection
Inspection of the package-product for visible damage is allowed, provided
Product Specification
Cartons/Packaging Test Standard
Issue date: Jun 7, 04 Revision date: Page 4 of 4
Document EN111
inspection does not alter, in any way, the current condition of the package or the
condition or position of the product (s).
�������
Reference: “ISTA 2A/2B Series Integrity-Plus Test Procedure”
本文档为【ISTA2A】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑,
图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。