Device
Operating
Temperature Range Package
��� �
EASY SWITCHER
3.0 A STEP–DOWN
VOLTAGE REGULATOR
ORDERING INFORMATION
LM2576T–XX
LM2576TV–XX TJ = –40° to +125°C
Straight Lead
Vertical Mount
D2T SUFFIX
PLASTIC PACKAGE
CASE 936A
(D2PAK)
Order this document by LM2576/D
T SUFFIX
PLASTIC PACKAGE
CASE 314D
TV SUFFIX
PLASTIC PACKAGE
CASE 314B
LM2576D2T–XX Surface Mount
XX = Voltage Option, i.e. 3.3, 5, 12, 15 V; and ADJ for
Adjustable Output.
SEMICONDUCTOR
TECHNICAL DATA
1
5
1
5
1
5
DEVICE TYPE/NOMINAL OUTPUT VOLTAGE
LM2576–3.3
LM2576–5
LM2576–12
LM2576–15
LM2576–ADJ
3.3 V
5.0 V
12 V
15 V
1.23 V to 37 V
Pin 1. Vin
2. Output
3. Ground
4. Feedback
5. ON/OFF
Heatsink surface
connected to Pin 3.
Heatsink surface (shown as terminal 6 in case outline
drawing) is connected to Pin 3.
1MOTOROLA ANALOG IC DEVICE DATA
���! � ������ ���
������� � ������� ���������
The LM2576 series of regulators are monolithic integrated circuits ideally
suited for easy and convenient design of a step–down switching regulator
(buck converter). All circuits of this series are capable of driving a 3.0 A load
with excellent line and load regulation. These devices are available in fixed
output voltages of 3.3 V, 5.0 V, 12 V, 15 V, and an adjustable output version.
These regulators were designed to minimize the number of external
components to simplify the power supply design. Standard series of
inductors optimized for use with the LM2576 are offered by several different
inductor manufacturers.
Since the LM2576 converter is a switch–mode power supply, its efficiency
is significantly higher in comparison with popular three–terminal linear
regulators, especially with higher input voltages. In many cases, the power
dissipated is so low that no heatsink is required or its size could be reduced
dramatically.
A standard series of inductors optimized for use with the LM2576 are
available from several different manufacturers. This feature greatly simplifies
the design of switch–mode power supplies.
The LM2576 features include a guaranteed ±4% tolerance on output
voltage within specified input voltages and output load conditions, and ±10%
on the oscillator frequency (±2% over 0°C to 125°C). External shutdown is
included, featuring 80 µA (typical) standby current. The output switch
includes cycle–by–cycle current limiting, as well as thermal shutdown for full
protection under fault conditions.
Features
• 3.3 V, 5.0 V, 12 V, 15 V, and Adjustable Output Versions
• Adjustable Version Output Voltage Range, 1.23 to 37 V ±4% Maximum
Over Line and Load Conditions
• Guaranteed 3.0 A Output Current
• Wide Input Voltage Range
• Requires Only 4 External Components
• 52 kHz Fixed Frequency Internal Oscillator
• TTL Shutdown Capability, Low Power Standby Mode
• High Efficiency
• Uses Readily Available Standard Inductors
• Thermal Shutdown and Current Limit Protection
Applications
• Simple High–Efficiency Step–Down (Buck) Regulator
• Efficient Pre–Regulator for Linear Regulators
• On–Card Switching Regulators
• Positive to Negative Converter (Buck–Boost)
• Negative Step–Up Converters
• Power Supply for Battery Chargers
Motorola, Inc. 1999 Rev 1, 07/1999
LM2576
2 MOTOROLA ANALOG IC DEVICE DATA
Figure 1. Block Diagram and Typical Application
7.0 V – 40 V
Unregulated
DC Input
L1
100 µH
Gnd
+Vin
1
Cin
100 µF 3 ON/OFF5
Output
2
Feedback
4
D1
1N5822 Cout1000 µF
Typical Application (Fixed Output Voltage Versions)
Representative Block Diagram and Typical Application
Unregulated
DC Input
+Vin
1
Cout
Feedback
4
Cin
L1
D1
R2
R1
1.0 k
Output
2
Gnd
3
ON/OFF
5
Reset
Latch
Thermal
Shutdown
52 kHz
Oscillator
1.235 V
Band–Gap
Reference
Freq
Shift
18 kHz
Comparator
Fixed Gain
Error Amplifier
Current
Limit
Driver
1.0 Amp
Switch
ON/OFF3.1 V InternalRegulator
Regulated
Output
Vout
Load
Output
Voltage Versions
3.3 V
5.0 V
12 V
15 V
R2
(Ω)
1.7 k
3.1 k
8.84 k
11.3 k
For adjustable version
R1 = open, R2 = 0 Ω
LM2576
5.0 V Regulated
Output 3.0 A Load
ABSOLUTE MAXIMUM RATINGS (Absolute Maximum Ratings indicate limits beyond
which damage to the device may occur.)
Rating Symbol Value Unit
Maximum Supply Voltage Vin 45 V
ON/OFF Pin Input Voltage – –0.3 V ≤ V ≤ +Vin V
Output Voltage to Ground (Steady–State) – –1.0 V
Power Dissipation
Case 314B and 314D (TO–220, 5–Lead) PD Internally Limited W
Thermal Resistance, Junction–to–Ambient RθJA 65 °C/W
Thermal Resistance, Junction–to–Case RθJC 5.0 °C/W
Case 936A (D2PAK) PD Internally Limited W
Thermal Resistance, Junction–to–Ambient RθJA 70 °C/W
Thermal Resistance, Junction–to–Case RθJC 5.0 °C/W
Storage Temperature Range Tstg –65 to +150 °C
Minimum ESD Rating (Human Body Model:
C = 100 pF, R = 1.5 kΩ)
– 2.0 kV
Lead Temperature (Soldering, 10 seconds) – 260 °C
Maximum Junction Temperature TJ 150 °C
NOTE: ESD data available upon request.
LM2576
3MOTOROLA ANALOG IC DEVICE DATA
OPERATING RATINGS (Operating Ratings indicate conditions for which the device is
intended to be functional, but do not guarantee specific performance limits. For guaranteed
specifications and test conditions, see the Electrical Characteristics.)
Rating Symbol Value Unit
Operating Junction Temperature Range TJ –40 to +125 °C
Supply Voltage Vin 40 V
SYSTEM PARAMETERS ([Note 1] Test Circuit Figure 15)
ELECTRICAL CHARACTERISTICS (Unless otherwise specified, Vin = 12 V for the 3.3 V, 5.0 V, and Adjustable version, Vin = 25 V for
the 12 V version, and Vin = 30 V for the 15 V version. ILoad = 500 mA. For typical values TJ = 25°C, for min/max values TJ is the operating
junction temperature range that applies [Note 2], unless otherwise noted.)
Characteristics Symbol Min Typ Max Unit
LM2576–3.3 ([Note 1] Test Circuit Figure 15)
Output Voltage (Vin = 12 V, ILoad = 0.5 A, TJ = 25°C) Vout 3.234 3.3 3.366 V
Output Voltage (6.0 V ≤ Vin ≤ 40 V, 0.5 A ≤ ILoad ≤ 3.0 A) Vout V
TJ = 25°C 3.168 3.3 3.432
TJ = –40 to +125°C 3.135 – 3.465
Efficiency (Vin = 12 V, ILoad = 3.0 A) η – 75 – %
LM2576–5 ([Note 1] Test Circuit Figure 15)
Output Voltage (Vin = 12 V, ILoad = 0.5 A, TJ = 25°C) Vout 4.9 5.0 5.1 V
Output Voltage (8.0 V ≤ Vin ≤ 40 V, 0.5 A ≤ ILoad ≤ 3.0 A) Vout V
TJ = 25°C 4.8 5.0 5.2
TJ = –40 to +125°C 4.75 – 5.25
Efficiency (Vin = 12 V, ILoad = 3.0 A) η – 77 – %
LM2576–12 ([Note 1] Test Circuit Figure 15)
Output Voltage (Vin = 25 V, ILoad = 0.5 A, TJ = 25°C) Vout 11.76 12 12.24 V
Output Voltage (15 V ≤ Vin ≤ 40 V, 0.5 A ≤ ILoad ≤ 3.0 A) Vout V
TJ = 25°C 11.52 12 12.48
TJ = –40 to +125°C 11.4 – 12.6
Efficiency (Vin = 15 V, ILoad = 3.0 A) η – 88 – %
LM2576–15 ([Note 1] Test Circuit Figure 15)
Output Voltage (Vin = 30 V, ILoad = 0.5 A, TJ = 25°C) Vout 14.7 15 15.3 V
Output Voltage (18 V ≤ Vin ≤ 40 V, 0.5 A ≤ ILoad ≤ 3.0 A) Vout V
TJ = 25°C 14.4 15 15.6
TJ = –40 to +125°C 14.25 – 15.75
Efficiency (Vin = 18 V, ILoad = 3.0 A) η – 88 – %
LM2576 ADJUSTABLE VERSION ([Note 1] Test Circuit Figure 15)
Feedback Voltage (Vin = 12 V, ILoad = 0.5 A, Vout = 5.0 V, TJ = 25°C) Vout 1.217 1.23 1.243 V
Feedback Voltage (8.0 V ≤ Vin ≤ 40 V, 0.5 A ≤ ILoad ≤ 3.0 A, Vout = 5.0 V) Vout V
TJ = 25°C 1.193 1.23 1.267
TJ = –40 to +125°C 1.18 – 1.28
Efficiency (Vin = 12 V, ILoad = 3.0 A, Vout = 5.0 V) η – 77 – %
NOTES: 1. External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. When the
LM2576 is used as shown in the Figure 15 test circuit, system performance will be as shown in system parameters section.
2. Tested junction temperature range for the LM2576: Tlow = –40°C Thigh = +125°C
LM2576
4 MOTOROLA ANALOG IC DEVICE DATA
DEVICE PARAMETERS
ELECTRICAL CHARACTERISTICS (Unless otherwise specified, Vin = 12 V for the 3.3 V, 5.0 V, and Adjustable version, Vin = 25 V for
the 12 V version, and Vin = 30 V for the 15 V version. ILoad = 500 mA. For typical values TJ = 25°C, for min/max values TJ is the operating
junction temperature range that applies [Note 2], unless otherwise noted.)
Characteristics Symbol Min Typ Max Unit
ALL OUTPUT VOLTAGE VERSIONS
Feedback Bias Current (Vout = 5.0 V [Adjustable Version Only]) Ib nA
TJ = 25°C – 25 100
TJ = –40 to +125°C – – 200
Oscillator Frequency [Note 3] fosc kHz
TJ = 25°C – 52 –
TJ = 0 to +125°C 47 – 58
TJ = –40 to +125°C 42 – 63
Saturation Voltage (Iout = 3.0 A [Note 4]) Vsat V
TJ = 25°C – 1.5 1.8
TJ = –40 to +125°C – – 2.0
Max Duty Cycle (“on”) [Note 5] DC 94 98 – %
Current Limit (Peak Current [Notes 3 and 4]) ICL A
TJ = 25°C 4.2 5.8 6.9
TJ = –40 to +125°C 3.5 – 7.5
Output Leakage Current [Notes 6 and 7], TJ = 25°C IL mA
Output = 0 V – 0.8 2.0
Output = –1.0 V – 6.0 20
Quiescent Current [Note 6] IQ mA
TJ = 25°C – 5.0 9.0
TJ = –40 to +125°C – – 11
Standby Quiescent Current (ON/OFF Pin = 5.0 V (“off”)) Istby µA
TJ = 25°C – 80 200
TJ = –40 to +125°C – – 400
ON/OFF Pin Logic Input Level (Test Circuit Figure 15) V
Vout = 0 V VIH
TJ = 25°C 2.2 1.4 –
TJ = –40 to +125°C 2.4 – –
Vout = Nominal Output Voltage VIL
TJ = 25°C – 1.2 1.0
TJ = –40 to +125°C – – 0.8
ON/OFF Pin Input Current (Test Circuit Figure 15) µA
ON/OFF Pin = 5.0 V (“off”), TJ = 25°C IIH – 15 30
ON/OFF Pin = 0 V (“on”), TJ = 25°C IIL – 0 5.0
NOTES: 3. The oscillator frequency reduces to approximately 18 kHz in the event of an output short or an overload which causes the regulated output voltage to
drop approximately 40% from the nominal output voltage. This self protection feature lowers the average dissipation of the IC by lowering the
minimum duty cycle from 5% down to approximately 2%.
4. Output (Pin 2) sourcing current. No diode, inductor or capacitor connected to output pin.
5. Feedback (Pin 4) removed from output and connected to 0 V.
6. Feedback (Pin 4) removed from output and connected to +12 V for the Adjustable, 3.3 V, and 5.0 V versions, and +25 V for the 12 V and 15 V
versions, to force the output transistor “off”.
7. Vin = 40 V.
LM2576
5MOTOROLA ANALOG IC DEVICE DATA
I Q
,
QU
IES
CE
NT
CU
RR
EN
T (
mA
)
40
TYPICAL PERFORMANCE CHARACTERISTICS (Circuit of Figure 15)
V o
ut
,
OU
TP
UT
VO
LT
AG
E
CH
AN
GE
(%
)
V o
ut
,
OU
TP
UT
VO
LT
AG
E
CH
AN
GE
(%
)
,
ST
AN
DB
Y
QU
IES
CE
NT
CU
RR
EN
T (
TJ, JUNCTION TEMPERATURE (°C)
I O
,
OU
TP
UT
CU
RR
EN
T (
A)
TJ, JUNCTION TEMPERATURE (°C)
Vin, INPUT VOLTAGE (V)
Vin, INPUT VOLTAGE (V)
IN
PU
T –
OU
TP
UT
DI
FF
ER
EN
TI
AL
(V)
TJ, JUNCTION TEMPERATURE (°C)
Figure 2. Normalized Output Voltage
TJ, JUNCTION TEMPERATURE (°C)
Figure 3. Line Regulation
Figure 4. Dropout Voltage Figure 5. Current Limit
Figure 6. Quiescent Current Figure 7. Standby Quiescent Current
ILoad = 200 mA
ILoad = 3.0 A
Vin = 12 V
Vin = 40 V
L1 = 150 µH
Rind = 0.1 Ω
ILoad = 500 mA
ILoad = 3.0 A
Vout = 5.0 V
Measured at
Ground Pin
TJ = 25°C
VON/OFF = 5.0 V
µA
)
1.0
0.6
0.2
0
–0.2
–0.4
–1.0
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
–0.2
–0.4
–0.6
2.0
1.5
1.0
0.5
0
6.5
6.0
5.5
5.0
4.5
4.0
20
18
16
14
12
10
8.0
6.0
4.0
200
180
160
140
120
100
80
60
20
0
1251007550250–25–50 403530252015105.00
1251007550250–25–50 1251007550250–25–50
403530252015105.00 1251007550250–25–50
–0.8
–0.6
0.4
0.8 Vin = 20 V
ILoad = 500 mA
Normalized at TJ = 25°C
ILoad = 500 mA
TJ = 25°C
3.3 V, 5.0 V and ADJ
12 V and 15 V
Vin = 25 V
I s
tby
LM2576
6 MOTOROLA ANALOG IC DEVICE DATA
V s
at
,
SA
TU
RA
TI
ON
V
OL
TA
GE
(V
)
2.0
2.5
3.0
4.0
I b,
FE
ED
BA
CK
P
IN
C
UR
RE
NT
(nA
)
,
ST
AN
DB
Y
QU
IES
CE
NT
CU
RR
EN
T (
µA
)
I s
tby
,
IN
PU
T V
OL
TA
GE
(V
)
TJ, JUNCTION TEMPERATURE (°C)
SWITCH CURRENT (A)
NO
RM
AL
IZE
D
FR
EQ
UE
NC
Y (
%)
TJ, JUNCTION TEMPERATURE (°C)
Figure 8. Standby Quiescent Current
Vin, INPUT VOLTAGE (V)
Figure 9. Switch Saturation Voltage
Figure 10. Oscillator Frequency Figure 11. Minimum Operating Voltage
Figure 12. Feedback Pin Current
Vin = 12 V
Normalized at
25°C
TJ = 25°C
Adjustable Version Only
200
180
140
120
100
80
60
40
20
0
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
8.0
6.0
4.0
2.0
0
–2.0
–4.0
–6.0
–8.0
–10
5.0
4.5
3.5
1.5
1.0
0.5
0
40302520151050 0 0.5 1.0 1.5 2.0 3.0
1251007550250–25–50 1251007550250–25–50
TJ, JUNCTION TEMPERATURE (°C)
Adjustable Version Only
100
80
60
40
20
0
–20
–40
–60
–80
–100
1251007550250–25–50
160
35 2.5
–40°C
25°C
125°C
Vout � 1.23 V
ILoad = 500 mA
TYPICAL PERFORMANCE CHARACTERISTICS (Circuit of Figure 15)
V i
n
LM2576
7MOTOROLA ANALOG IC DEVICE DATA
2.0 A
0
0
A
B
C
100 µs/DIV5 µs/DIV
Figure 13. Switching Waveforms Figure 14. Load Transient Response
Vout = 15 V
A: Output Pin Voltage, 10 V/DIV
B: Inductor Current, 2.0 A/DIV
C: Inductor Current, 2.0 A/DIV, AC–Coupled
D: Output Ripple Voltage, 50mV/dDIV, AC–Coupled
Horizontal Time Base: 5 µs/DIV
50 V
0
4.0 A
2.0 A
100 mV
Output
Voltage
Change
0
3.0 A
2.0 A
1.0 A
0
4.0 A
– 100 mV
Load
Current
TYPICAL PERFORMANCE CHARACTERISTICS (Circuit of Figure 15)
D
LM2576
8 MOTOROLA ANALOG IC DEVICE DATA
Figure 15. Typical Test Circuit
D1
MBR360
L1
100 µHOutput
2
4
Feedback
Cout
1000 µF
Cin
100 µF
LM2576
Fixed Output1
53 ON/OFFGnd
Vin
Load
Vout
D1
MBR360
L1
100 µHOutput
2
4
Feedback
Cout
1000 µF
Cin
100 µF
LM2576
Adjustable1
53 ON/OFFGnd
Vin
Load
Vout
5,000 V
Fixed Output Voltage Versions
Adjustable Output Voltage Versions
Vout� Vref �1.0�
R2
R1
�
R2� R1�
Vout
Vref
– 1.0�
Where Vref = 1.23 V, R1
between 1.0 k and 5.0 k
R2
R1
Cin – 100 µF, 75 V, Aluminium Electrolytic
Cout – 1000 µF, 25 V, Aluminium Electrolytic
D1 – Schottky, MBR360
L1 – 100 µH, Pulse Eng. PE–92108
R1 – 2.0 k, 0.1%
R2 – 6.12 k, 0.1%
7.0 V – 40 V
Unregulated
DC Input
7.0 V – 40 V
Unregulated
DC Input
PCB LAYOUT GUIDELINES
As in any switching regulator, the layout of the printed
circuit board is very important. Rapidly switching currents
associated with wiring inductance, stray capacitance and
parasitic inductance of the printed circuit board traces can
generate voltage transients which can generate
electromagnetic interferences (EMI) and affect the desired
operation. As indicated in the Figure 15, to minimize
inductance and ground loops, the length of the leads
indicated by heavy lines should be kept as short as possible.
For best results, single–point grounding (as indicated) or
ground plane construction should be used.
On the other hand, the PCB area connected to the Pin 2
(emitter of the internal switch) of the LM2576 should be kept
to a minimum in order to minimize coupling to sensitive
circuitry.
Another sensitive part of the circuit is the feedback. It is
important to keep the sensitive feedback wiring short. To
assure this, physically locate the programming resistors near
to the regulator, when using the adjustable version of the
LM2576 regulator.
LM2576
9MOTOROLA ANALOG IC DEVICE DATA
PIN FUNCTION DESCRIPTION
Pin Symbol Description (Refer to Figure 1)
1 Vin This pin is the positive input supply for the LM2576 step–down switching regulator. In order to minimize
voltage transients and to supply the switching currents needed by the regulator, a suitable input bypass
capacitor must be present (Cin in Figure 1).
2 Output This is the emitter of the internal switch. The saturation voltage Vsat of this output switch is typically 1.5 V.
It should be kept in mind that the PCB area connected to this pin should be kept to a minimum in order to
minimize coupling to sensitive circuitry.
3 Gnd Circuit ground pin. See the information about the printed circuit board layout.
4 Feedback This pin senses regulated output voltage to complete the feedback loop. The signal is divided by the
internal resistor divider network R2, R1 and applied to the non–inverting input of the internal error amplifier.
In the Adjustable version of the LM2576 switching regulator this pin is the direct input of the error amplifier
and the resistor network R2, R1 is connected externally to allow programming of the output voltage.
5 ON/OFF It allows the switching regulator circuit to be shut down using logic level signals, thus dropping the total
input supply current to approximately 80 µA. The threshold voltage is typically 1.4 V. Applying a voltage
above this value (up to +Vin) shuts the regulator off. If the voltage applied to this pin is lower than 1.4 V or
if this pin is left open, the regulator will be in the “on” condition.
DESIGN PROCEDURE
Buck Converter Basics
The LM2576 is a “Buck” or Step–Down Converter which is
the most elementary forward–mode converter. Its basic
schematic can be seen in Figure 16.
The operation of this regulator topology has two distinct
time periods. The first one occurs when the series switch is
on, the input voltage is connected to the input of the inductor.
The output of the inductor is the output voltage, and the
rectifier (or catch diode) is reverse biased. During this period,
since there is a constant voltage source connected across
the inductor, the inductor current begins to linearly ramp
upwards, as described by the following equation:
IL(on)�
�Vin – Vout� ton
L
During this “on” period, energy is stored within the core
material in the form of magnetic flux. If the inductor is properly
designed, there is sufficient energy stored to carry the
requirements of the load during the “off” period.
Figure 16. Basic Buck Converter
DVin RLoad
L
Cout
Power
Switch
The next period is the “off” period of the power switch.
When the power switch turns off, the voltage across the
inductor reverses its polarity and is clamped at one diode
voltage drop below ground by the catch diode. The current
now flows through the catch diode thus maintaining the load
current loop. This removes the stored energy from the
inductor. The inductor current during this time is:
IL(off)�
�Vout – VD� toff
L
This period ends when the power switch is once again
turned on. Regulation of the converter is accomplished by
varying the duty cycle of the power switch. It is possible to
describe the duty cycle as follows:
d�
ton
T , where T is the period of switching.
For the buck converter with ideal components, the duty
cycle can also be described as:
d�
Vout
Vin
Figure 17 shows the buck converter, idealized waveforms
of the catch diode voltage and the inductor current.
Power
Switch
Figure 17. Buck Converter Idealized Waveforms
Power
Switch
Off
Power
Switch
Off
Power
Switch
On
Power
Switch
On
Von(SW)
VD(FWD)
Time
Time
ILoad(AV)
Imin
Ipk
Diode Diode
Power
Switch
Di
od
e V
olt
ag
e
Ind
uc
tor
C
urr
en
t
LM2576
10 MOTOROLA ANALOG IC DEVICE DATA
Procedure (Fixed Output Voltage Version) In order to simplify the switching regulator design, a step–by–step
design procedure and some examples are provided.
Procedure Example
Given Parameters:
Vout = Regulated Output Voltage (3.3 V, 5.0 V, 12 V or 15 V)
Vin(max) = Maximum Input Voltage
ILoad(max) = Maximum Load Current
Given Parameters:
Vout = 5.0 V
Vin(max) = 15 V
ILoad(max) = 3.0 A
1. Controller IC Selection
According to the required input voltage, output voltage and
current, select the appropriate type of the controller IC output
voltage version.
1. Controller IC Selection
According to the required input voltage, output voltage, current
polarity and current value, use the LM2576–5 controller IC
2. Input Capacitor Selection (Cin)
To prevent large voltage transients from appearing at the input
and for stable operation of the converter, an aluminium or
tantalum electrolytic bypass capacitor is needed between the
input pin +Vin and ground pin Gnd. This capacitor should be
located close to the IC using short leads. This capacitor should
have a low ESR (Equivalent Series Resistance) value.
2. Input Capacitor Selection (Cin)
A 100 µF, 25 V aluminium electrolytic capacitor located near to
the input and ground pins provides sufficient bypassing.
3. Catch Diode Selection (D1)
A. Since the diode maximum peak current exceeds the
本文档为【LM2576-ADJ】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑,
图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。