电池规格书模板.

Specification Approval Sheet 产品规格承认书 Customer    客户名称：域拓 Model                        产品型号：4L Type                   产品类型：Li-ion battery Specification产品规格：3.7V/1400mAH signed by client 客户签名 Confirmed确认：   Checked 审核：   Approved 批准：       signed by manufacturer 生产商签名 Prepared 制定： 肖泽建 Checked 审核：   Approved 批准： 丁明谊     AMENDMENT RECORDS Modification Time Description Issued Date Approved By 0 New release 2015-06-26                                                                                                                           Catalogue  目    录 1 .Battery type and scope电池型号和适用范围    4 1 . 1: model产品型号：    4 1 . 2: scope适用范围：客户定义    4 2 . Basic character and compose of battery电池的基本特性及组成    4 2 . 1: fundamental performance parameter of battery电池基本性能参数：    4 2 . 2: Main components and parts主要零部件    6 2 . 3: Regular performance and unfailing performance产品常规性能和可靠性能    6 2 . 4: Contour Dimension of the Battery电池外形尺寸    11 3 . Specifications of Parts零部件规格    112 3 . 1: fender保护板    122 3 . 2: general electric and protection characters一般电气与保护特征    122 3 . 2: electric schematic diagram of battery电池电路原理图：    133 3 . 3 : PCB layout 电路布局图………………………………………………………………….错误!未定义书签。3 4 . Specifications of the Cells电芯规格    144 Announcements注意事项    155 Danger  危险    155 Warnings  警告    166 Announcements  注意事项    167 1 .Battery type and scope电池型号和适用范围  This Specification Approval Sheet is for rechargeable Li-polymer battery provided by Shirui Battery Co., LTD. This product is according with the national standard of PRC. ‘GB/T18287-2000’. ‘General specification of lithium-ion battery for cellular phone’. 本《规格书》为时瑞电池有限公司提供的可充电式锂离子电池规格。 此产品符合中华人民共和国国家 标准 excel标准偏差excel标准偏差函数exl标准差函数国标检验抽样标准表免费下载红头文件格式标准下载 ‘GB/T18287-2000’《蜂窝电话用锂离子电池总规范》。 1 . ：model产品型号：4L 2 . Basic character and compose of battery电池的基本特性及组成 2 . 1： fundamental performance parameter of battery电池基本性能参数： S/N 序号 Details 内 容 parameters 参 数 remarks 备 注 1 Rated voltage 额定电压 3.7V   2 Rated capacity 额定容量 1400mAH discharge with 0.2C to 2.75V after Complete charge within 1h, measuring the discharge power 完全充电后1小时内,用0.2C放电至2.75V，测量其放电电量。   截止电压 2.9-3.1V   3 Limited charge voltage 充电限制电压 4.25V   4 internal resistance 内 阻 ≤150mΩ   5 charge mode 充电方式 C.C/C.V. 恒流/恒压方式 恒流/恒压 6 Charge time 充电时间 6H Standard charging 0.2C 280mA 标准充电0.2C（280mA） 2.5H 1C（280mA） 7 Max Charge Current 最大充电电流 1400mA   9 Max discharge current 最大放电电流 Lasting 持 续：1400mA Transient peak瞬间峰值： 2800mA   10 Working temperature 工作温度 charging充电时 0~45℃   discharging放电时 -20~60℃ 11 Storage temperature 贮存温度 1 Month一个月 -20~60℃ Charge to 40%~50% of capacity when storage 贮存时应充电至容量的40%~50% 6 months六个月 -20~30℃ 12 Storage humidity 贮存湿度 Relative humidity 65 ± 20%RH relative humidity 相对湿度 13 weight 重 量 约32g   14 Self-discharging 自放电 When the battery pack is without load, certain operational current is consumed since the cell protects the circuit, thus leading to the bringing down of pack voltage. For long storing time, please supplement the charging and note the “seventh. Special notice”   Pack before shipping 出贷标准 Charged with about 25-35% power and the voltage is 3.8-3.95 V being shipping. 15 Identify resistance ID识别电阻 68KΩ To ground 16 Cycle life 循环寿命 300 times 300循环次 capacity≥60﹪ 容量≥60﹪           If you need the battery protection parameters, please refer to PAGE 11. 如需参考电池保护参数，请参阅第11页。 2 . 2：Main components and parts主要零部件 Materials 材料 材料 model 型号规格 quantity 数 量 related technical parameters 相关技术参数 manufacturer 厂商 li-ion battery cell 锂离子电池芯 484461AR 1PCS Please refer to the battery cell specification 请参照电芯规格书 / protection board 保 护 板 XHY-FHLN-4L 1PCS / /           2 . 3：Regular performance and unfailing performance产品常规性能和可靠性能 S/N 序号 inspection item 检验项目 Standard 标 准 Testing Method 测试 方法 快递客服问题件处理详细方法山木方法pdf计算方法pdf华与华方法下载八字理论方法下载 1 high temperature property 高温性能 discharge with 0.5C5A not less than 100mins under 55 + 2 ℃,the appearance without distortion and crack. 电池在55±2℃，用0.5C5A放电时间不少于102min,电池外观无变形、无爆裂. set the battery 2h in the environment with 55±2℃ after Complete charge, then discharge with 0.5C5A 完全充电后置于55±2℃,2h用0.5C5A放电 2 Low temperature property 低温性能 discharge with 0.2C5A not less than 3h under -20±2℃,the appearance without distortion and crack. 电池在-20±2℃，用0.2C5A放电时间不少于3h,电池外观无变形、无爆裂. set the battery 16-24h in the environment with -20±2℃ after Complete charge, then discharge with 0.5C5A,then set the battery in 20±5℃, 2h later observe the battery appearance 完全充电后置于-20±2℃,16-24h用0.2CA放电,结束后将电池置于20±5℃条件下搁置2h,观察电池外观. discharge with 0.2C5A not less than 3.5h under -10±2℃,the appearance without distortion and crack 在-10±2℃，用0.2C5A放电时间不少于3.5h,电池外观无变形、无爆裂. set the battery 16-24h in the environment with -10±2℃ after Complete charge, then discharge with 0.5C5A,then set the battery in 20±5℃, 2h later observe the battery appearance 完全充电后置于-10±2℃,16-24h用0.2C5A放电,结束后将电池置于20±5℃条件下搁置2h,观察电池外观. 3 Capability of keeping electricity 荷电保持能力 Discharge not less than 4.25h 放电时间不少于4.25h Open circuit 28d under the environment with 20±5℃ after complete charge, then discharge with 0.2C5A 完全充电后,在20±5℃条件下,将电开路搁置28d,再0.2C5A放电. 4 Constant damp and hot property 恒定湿热性能 Battery appearance should have no obvious deformation, rust, smoke or explosion, discharge time not less than 36min 电池外观应无明显变形、锈蚀、冒烟或爆炸，放电时间不低于36min. After complete charge, shelve the battery in the condition of 40±2℃ Relative humidity is 90% - 95% with constant temperature and humidity, 48h later, shelve it in 20±5℃ 2h, then discharge with 1C5A 完全充电后,在40±2℃,相对湿度为90%-95%的恒温恒湿条件下搁置48h后,再取出放在20±5℃条件下搁置2h 再以1C5A放电. 5 shake 振动 Battery appearance should have no obvious deformation, rust, smoke or explosion, voltage not less than 3.6V 电池外观应无明显变形、冒烟或爆炸，电池电压不低于3.6V. After fully charged with 0.38 mm amplitude, make 10Hz ~ 30Hz resonant frequency, batteries installed in vibration bench, set up X.Y.Z three direction from swept-frequency rate for 1oct/min, circular sweep frequency vibration 30min 完全充电后,以0.38mm振幅作谐振10Hz~55Hz的频率,将电池安装在振动台上,设置好X.Y.Z三个方向上从扫频速率为1oct/min, 循还扫频振动30min 6 Free Drop Test 自由跌落 Battery appearance should have no leakage, no smoke or explosion, but allowed slight deformation 电池允许轻微变形，但应不漏液,不冒烟,不爆炸。 After crash test, the sample batteries are dropped on the 18-20mm hardwood of the concert floor from 1000mm height according to positive and negative 6 direction of X,Y,Z. Each direction should test one time. 碰撞试验结束后,将样品电池从1000mm高处自由跌落于水泥地面上的18-20mm厚的硬木板上,从X,Y,Z正负六个方向每个方向1次. 7 Performance of overcharge protection 过充电保护性能 Batteries should be no explosion, no fire, no smoke or leakage 电池应不爆炸,不起火,不冒烟或漏液. After the battery is fully charged, the battery should be loaded 8h with constant current source. The constant current source sets to 2 times nominal voltage and current sets 2CA. 电池完全充电结束后,用恒流恒压源给电池加载8h,恒流恒源设定为2倍标称电压,电流设定为2C5A 8 Performance of over-discharge protection 过放电保护性能 Batteries should be no explosion, no fire, no smoke or leakage. 电池应不爆炸,不起火,不冒烟或漏液. Under the conditions of an ambient temperature 20±5℃,the battery discharge in the conditions of 0.2C5A until voltage is termination. And then, battery discharge 24h with connecting a 30Ωload resistance. 电池在环境温度20±5℃的条件下,以0.2C5A放电至终止电压后,外接30Ω负载电阻放电24h. 9 Performance of short-circuit protection 短路保护性能 Batteries should be no explosion, no fire, no smoke or leakage; batteries voltage is not less than N*3.6V after instantaneous charge. 电池应不爆炸,不起火,不冒烟或漏液;瞬时充电后电池电压不低于N*3.6V. After battery is fully charge, positive and negative electrode should be circuit 1h with 0.1Ω.And,battery should be charged 5S instantaneous with 1C5A after positive and negative electrode are cut off. 电池完全充电后,将正负极用0.1Ω电阻短路1h,将正负极断开后,电池以1C5A电流瞬时充电5S. 10 Short-circuit Test 短路 No fire, No explosion The outside temperature of battery is not higher 150℃. 不起火,不爆炸,电池外部温度不高于150℃. Keep the connected electric couple battery in a fume hood and make positive and negative short circuit(the total resistance should be less than 50mΩ). Tester should monitor temperature changes. If the temperature of battery drops to about 10℃ lower than the max temperature, test is finished. 本项试验将接有电热偶的电池置于通风橱中,短路其正负极(线路总电阻不大于50mΩ),监视温度变化,当电池温度下降到比峰值低约10℃时,试验结束. 11 Cycle life 循环寿命 Charging life cycle is over 300 times 循环寿命不低于300次 容量大于60%. After 300 cycle， Capacity ≥60% The battery used for testing of cycle life should be charged with constant 0.5CA at constant temperature of 20℃±5℃. The battery is charged with constant voltage till 20mA when it is charged to the limited voltage. Then discharge it with constant 0.5C5A till the end voltage after stop charging for 0.5-1h, repeat the next cycle. It means the discharging time less than 36min of two consecutive cycles while reaching its end of the life. 电池循环寿命试验应在20℃±5℃,以0.5CA充电,当电池端电压达到充电限制电压时,改为恒压充电,直到充电电流小于或等于20mA,停止充电搁置0.5h-1h,然后以0.5C5A电流放电至终止电压,放电结束后,搁置0.5-1h,再进行下一个循环,直至连续两次放电时间小于36min.则认为寿命终止. 12 Storage 贮存 Fullychargethebattery,whichisnewmanufacturedshorterthan3months,with0.2C,thendischargetimeslessthen4hours . 电池贮存3个月,经完全充电后,0.2C5A,放电时间不小于4h. The storage test of battery should be selected a battery which is less than 3 month from production date to the date of experiment. Before storage, battery capacity should be full charged 40%~50% capacity, the ambient temperature is 20℃±5℃ and relative humidity is 45%-75%.After the storage expiration of battery, battery should be charged and discharged according to fully charged and discharged. 进行贮存试验的电池应选自生产日期到试验日期不足3个月的电池,电池贮存前应按完全充电的40%~50%的容量,在环境温度20℃±5℃,相对湿度45%-75%的环境中贮存,贮存期满后,电池按完全充放电制进行充放电.                 2 . 4:Contour Dimension of the Battery电池外形尺 2.5 Label（Not to scale）标贴 3 . Specifications of Parts零部件规格 3 . 1: fender DW01-P,8205A保护板DW01-P,8205A 3 . 2:general electric and protection characters一般电气与保护特征 Model of Protection IC : DW01-P 保护IC的型号：DW01-P Items 项 目 Specification 规 格 Remarks 备 注 Over-charging Protection Voltage 过充电保护电压 4.28V±0.05V   Over-charging Return Voltage 过充回复电压 4.08V±0.10V   Over-discharge Protection Voltage 过放电保护电压 2.4V±0.10V   Over-discharge Return Voltage 过放回复电压 3.0V±0.10V   Over-current Protection 过电流保护 2-5A   Detection Delay Time of Over-charging Protection 过充电保护侦测延时时间 ≤200ms   Detection Delay Time of Over-discharging Protection 过放电保护侦测延时时间 ≤120mS   Detection Delay Time of Over-current Protection 过电流保护侦测延时时间 ≤20mS   Detection Delay Time of Output short-circuit Protection 输出短路保护侦测延时时间 ≤320US(Typical)   Internal Resistance of Proper Functioning 正常工作内阻 ≤60mΩ   Consume Current 消耗电流 ≤6.0uA         3 . 2 electric schematic diagram of battery电池电路原理图： 3.3 PCB layout 电路布局图 Top Layer Lower layer 4 . Specifications of the Cells电芯规格 NO. 序号 Items 项目 Parameters 参数 Tolerance 公差 Term 条件 Remark/ condition 备注/条件 1 Appearance 外观 No mechanical damage, leakage , sink ,drum and so on 无机械损伤、漏液、下陷、发鼓等现象 / 50cm distance under 40W daylight lamp 在40W日光灯下50CM处 Visual 目视 2 Dimensions 尺寸 Length 长 61.0mm -0.5mm Digital caliper 数显卡尺   Width 宽 44.0mm -0.3mm Thickness 厚 4.8mm +0.1mm 3 Voltage 电压 3.85-3.92V / 万用表   4 Capacity 容量 ≥1400mAH / 0.2C   5 Internal resistance 内阻 ≤60mΩ / 1KHz / 6 Consistency 同批一致性 Appearance quality is the same 同批外观质量相同 7 Security 安全性 Correspond to related safety performance 符合相关安全性能                 5 保质期 电池的保质期为出厂后一年。本公司承诺如果在一年中由于电池本身的质量问 题 快递公司问题件快递公司问题件货款处理关于圆的周长面积重点题型关于解方程组的题及答案关于南海问题 ，本公司将负责进行调换，如果是由于用户误用而产生的问题，不予调换。 Announcements  注意事项 Danger  危险 To prevent battery from weeping, fever, exploding ,please obey the rules as follows: 为了防止电池漏液、发热、爆炸,请遵守以下防范事项： Do not immerse the battery into the water or the sea, Guard against Damp; 不要将电池浸入水或海水中,注意防潮。 Do not approach the heat source, like fire or heater; 不要将电池接近热源,如火或发热器。 Please use the appointed charger when charging; 在充电时,请用指定的充电器。 Do not transposition the +.- poles of the battery to charge; 不要反接电池的+ -极进行充电。 Do not direct-connected the battery to alternating current power supply, or autoignition of the vehicle; 不要将电池直接连接在交流电源,或者车辆自动点火处。 Do not discard the battery to the fire or hyperpyretic objects; 不要将电池弃置于火里或高热的物体上。 Do not use the conductor to lead the short circuit of the + -poles of the battery. Do not put the battery with metallic conductors to transport or store, like necklace, hairpin and so on; 不要将电池的+ -极用导体短路、不要把电池和金属导体,如项链、发夹等一起运输或存储。 Do not beat or throw the battery; 不要敲打或丢抛电池。 Do not impale the battery with needle or some other sharp things, do not strike it with weight; 不要用针或其它锋利物刺穿电池,不要用重物击打电池。 As installed safety device in the battery, please do not resolve or change any other sections of the battery to protect the inherent safety functions; 电池内有安全装置,为了保证其固有的安全功能,请不要将电池分解开或改变任何的部份。 Warnings  警告 Do not put the battery to the microwave oven or pressure tank; 不要将电池放入微波炉或压力柜子里。 Do not use the battery with some chemical batteries (like dry battery) or different capacities and brands battery together, if the battery emits the smell, heat , changes color, be out of shape or appears any other abnormal phenomena during the charging or stored procedures, please get out the battery from the device or charger and stop using; 不要将电池与其它化学电池(像干电池)或不同容量、牌子的电池合用,若电发出气味、发热、变色、变形或者在使用充电、存储过程中,出现任何的不正常请立即从装置或充电器取出,停止使用。 If can not recharge within the charging period, please not continue charging; 指定充电时间内若不能再充电请不用继续充电。 Put the battery to where the kids can not touch, if the kids swallow the battery , please seeing the doctor soon; 电池放于小孩不能触摸的地方,若小孩咽下电池,请立即就医。 If the electrolyte of the battery into the eyes, do not rub ,should wash the eyes first ,then see the doctor; 若电池电解质进入眼睛,切勿揉眼睛,先用清水冲洗眼睛后立即就医。           Announcements  注意事项 Do not put the battery under the high temperature places (like sunshine irradiation or car in the hot weather), or it will catch fire for the heat , reduce the performance and loss the life; 不要将电池放于高温处(如阳光直射或热天下汽车里)否则,会过热着火,性能降低和寿命缩短。 To insure the safety, the battery should install the safety device, please not use when the static electricity is more than we need when produce, or the safety device will lose efficacy and lead the overheating ,fracture, exploding and catching fire; 为确保安全,电池应安装安全装置,在静电强于制造时所 要求 对教师党员的评价套管和固井爆破片与爆破装置仓库管理基本要求三甲医院都需要复审吗 的静电时请勿使用,否则,安全装置会失效,导致电池过热、破裂、爆炸及着火。 Please use the battery in normal as follows, or it will be overheating, caught fire , reduced performance and shorten the life; 请在下列条件下正常使用,否则会过热、着火、性能降低及缩短寿命 Environment condition 环境条件: (T temperature)    charging: 0~+400C (T温度)            充电:  0~+400C Discharging: -20~+600C 放电:  -20~+600C Store within 30 days: -20～+500C 30天内保存: -20～+500C Store within 90 days : -20～+350C 90天内保存: -20～+350C If the kids use the battery, they should use as the operation instruction manual and guarantee that it must be use in normal at any time; 如果小孩使用电池,应指定他们按使用说明书进行使用且保证电池在任何时候都必须是正常使用。                                    If the battery weep, the electrolytes stick on the skin or cloth, use the water to wash or running water to wash  若电池漏液,电解质粘于皮肤或衣服上,用水冲洗掉或用流水洗衣服。 To insure not install the battery wrong or wastage of the battery, please read the instruction carefully to install and dismounting; 为了不装错或损耗电池,请认真阅读使用说明书进行安装与拆卸(从装置上)。 If the battery will not be used for a long time ,please take out of the battery from the device and store in dry and shady places; 若电池长时间不用时,请把电池从设备中拿出并存放于干燥阴凉的地方。 If there are splodge on the surface of the battery, please wipe up clean before using, or it will lead bad contact with the device. 若电池接触面有污迹,请在使用之前用干布擦干凈,否则将导致与装置接触不良。