E-Book - Injection Hdi Bosch Edc 15c2 Pour Moteur Dv4Td - 153 Pp - English
CITROËN
CITROËN
TECHNICAL TRAINING
BOSCH HDI EDC 15C2
INJECTION SYSTEM AND
PARTICLE FILTER
DOCUMENT REF N?: 1.6.243 August 2000
DEALER QUALITY
DEVELOPMENT DIVISION
NOTE TO READERS
This document contains information of a confidential nature.
It is therefore strictly reserved for the use of CITROËN trainers and may not
be distributed to people outside the relevant departments.
A
BROCHURE SUMMARY
BOSCH EDC 15C2 HDI SYSTEM (High pressure
Diesel Injection)
COMBINED WITH A PARTICLE FILTER SYSTEM
The aim of this brochure is to define the composition and operation of a BOSCH EDC 15 C2 HDI diesel engine management system, combined with a particle filter system, in relation to the DW12 Diesel engine.
This device consists of an ECU which analyses the information from the various sensors, and then operates the injectors at the correct moment. It also controls a pressure regulator, the exhaust gas recycling electrovalve and the turbocharging pressure modulating electrovalve.
The following subjects are dealt with in this document:
- General details and system presentation,
- Description and operation of the components of the various functions, or the
functions themselves,
- Description of the operating phases:
, of the injection system,
, of the particle filter system.
- Notes on maintenance,
- The electrical circuit.
B
CONTENTS
CHAPTER 1: GENERAL DETAILS: HDI DIRECT INJECTION SYSTEM .. 1
I - FOREWORD ......................................................................................................... 1
II - PRINCIPLE OF HDI ............................................................................................... 4
III - PARTICLE FILTRATION PRINCIPLE .................................................................... 5
IV - SAFETY INSTRUCTIONS ..................................................................................... 6
CHAPTER 2: GENERAL LAYOUT: HDI SYSTEM .................................... 9
CHAPTER 3: FUEL SUPPLY FUNCTION ................................................ 13
I - DIAGRAM ............................................................................................................ 13
II - COMPONENTS COMMON WITH DOCUMENT "BOSCH EDC 15C2 HDI
INJECTION SYSTEM" ......................................................................................... 15
III - SPECIFIC COMPONENTS .................................................................................. 15
IV - ELECTRIC FUEL HEATER (1276) ...................................................................... 16
V - LOW PRESSURE PUMP SUPPLY CUT-OFF ...................................................... 16
CHAPTER 4: AIR SUPPLY FUNCTION .................................................... 17
I - DIAGRAM ............................................................................................................ 17
II - COMPONENTS COMMON WITH DOCUMENT "BOSCH EDC 15C2 HDI
INJECTION SYSTEM" ......................................................................................... 20
III - SPECIFIC COMPONENTS .................................................................................. 20
IV - VACUUM RESERVE ........................................................................................... 21
V - VARIABLE GEOMETRY TURBOCHARGER ........................................................ 22
VI - VARIABLE "SWIRL" ............................................................................................ 26
VII - SWIRL CONTROL ELECTROVALVE (1264) ..................................................... 27
VIII - FEATURE: INLET MANIFOLD PRESSURE SENSOR (1312) ............................. 28
C
CONTENTS
CHAPTER 5: EXHAUST GAS RECYCLING FUNCTION ......................... 29 I - DIAGRAM ........................................................................................................... 29 II - COMPONENTS COMMON WITH DOCUMENT "BOSCH EDC 15C2 HDI
INJECTION SYSTEM"......................................................................................... 32 III - SPECIFIC COMPONENTS ................................................................................. 32 IV - WATER/EXHAUST GAS EXCHANGER (EGR) .................................................. 32 V - THROTTLE HOUSING (EGR) ............................................................................. 32 VI - THROTTLE HOUSING CONTROL ELECTROVALVE (EGR) (1263) .................. 33
CHAPTER 6: HDI SYSTEM ....................................................................... 35 I - COMPONENTS COMMON WITH DOCUMENT "BOSCH EDC 15C2 HDI
INJECTION SYSTEM"......................................................................................... 35 II - SPECIFIC COMPONENTS ................................................................................. 36 III - DOUBLE INJECTION RELAY (BSM) - FEATURE .............................................. 36 IV - COOLANT TEMPERATURE SENSOR (1220) - FEATURE ................................ 37 V - FUEL TEMPERATURE SENSOR (1221) - FEATURE ......................................... 39 VI - BRAKE SWITCH (2100) - FEATURE ................................................................. 40 VII - CRUISE CONTROL BRAKE PEDAL SWITCH (7308) - FEATURE..................... 40 VIII - CLUTCH SWITCH (7306) - FEATURE ............................................................... 40 IX - VEHICLE SPEED SENSOR - FEATURE ............................................................ 40 X - INJECTION ECU (1320) - FEATURE .................................................................. 41
CHAPTER 7: PRE-POST HEATING FUNCTION ..................................... 47 I - COMPONENTS COMMON WITH DOCUMENT "BOSCH EDC 15C2 HDI
INJECTION SYSTEM"......................................................................................... 47 II - PREHEATER PLUGS (1160) - FEATURE ........................................................... 47
D
CONTENTS
CHAPTER 8: ENGINE COOLING FUNCTION (FRIC)
(INCORPORATED INTO THE INJECTION ECU) .............. 49
I - DIAGRAM ............................................................................................................ 50
II - FAN UNIT (1510) ................................................................................................. 52
III - COOLANT TEMPERATURE SENSOR (1220) ..................................................... 54
IV - POSTVENTILATION ........................................................................................... 54
V - DOWNGRADED MODE ....................................................................................... 54
CHAPTER 9: COOLING REQUIREMENTS FOR THE AIR
CONDITIONING (BRAC) (INCORPORATED INTO THE
INJECTION ECU) ................................................................ 55
I - DIAGRAM ............................................................................................................ 56
II - AIR CONDITIONING PRESSURESTAT (8007).................................................... 58
III - FAN UNIT (1510) ................................................................................................. 60
IV - DOWNGRADED MODE ...................................................................................... 60
CHAPTER 10: PARTICLE FILTER FUNCTION ....................................... 61
I - DIAGRAM ............................................................................................................ 61
II - PARTICLE FILTER .............................................................................................. 65
III - CATALYTIC CONVERTER .................................................................................. 67
IV - EXHAUST GAS TEMPERATURE SENSOR (UPSTREAM OF THE
CATALYTIC CONVERTER) (1344) ..................................................................... 68
V - EXHAUST GAS TEMPERATURE SENSOR (DOWNSTREAM OF THE
CATALYTIC CONVERTER) (1343) ...................................................................... 69
VI - DIFFERENTIAL PRESSURE SENSOR (1341) .................................................... 70
VII - AIR TEMPERATURE SENSOR (1310) ............................................................... 72
VIII - AIR/WATER HEAT EXCHANGER (HEATING OF THE INLET AIR) .................... 73
IX - INLET AIR HEATER THROTTLE ........................................................................ 73
X - THROTTLE HOUSING CONTROL ELECTROVALVE (HEATING OF
THE INLET AIR) (1285)........................................................................................ 74
XI - THROTTLE HOUSING CONTROL ELECTROVALVE (EGR) (1263) ................... 77
XII - BUILT-IN SYSTEMS INTERFACE (BSI1) ........................................................... 77
XIII - INJECTION ECU (1320) ..................................................................................... 81
E
CONTENTS
CHAPTER 11: FUEL ADDITIVE FUNCTION............................................ 83 I - ADDITIVE............................................................................................................ 83 II - ADDITIVE TANK ................................................................................................. 84 III - ADDITIVE INJECTION PUMP (1283) ................................................................. 85 III - LOW ADDITIVE LEVEL SENSOR (1283) ........................................................... 86 IV - SAFETY VALVE ................................................................................................. 87 V - ADDITIVE INJECTOR (1284) .............................................................................. 89 VI - FUEL FILLER CAP PRESENCE SENSOR (4320) .............................................. 90 VII - FUEL SENDER (1211) ....................................................................................... 91 VIII - BUILT-IN SYSTEMS INTERFACE (BSI1) .......................................................... 93 IX - FUEL ADDITIVE ECU (1282) ............................................................................. 93
CHAPTER 12: OPERATING PHASES: HDI DIRECT INJECTION
SYSTEM ............................................................................ 95 I - COMPONENTS COMMON WITH DOCUMENT "BOSCH EDC 15C2 HDI
INJECTION SYSTEM"......................................................................................... 95 II - SPECIFIC COMPONENTS ................................................................................. 96 III - TURBOCHARGING PRESSURE REGULATION - FEATURE ............................. 96 IV - EXHAUST GAS RECYCLING REGULATION ..................................................... 97 V - PRE-POST HEATING ......................................................................................... 99 VI - PREHEATING OPERATION .............................................................................. 99 VII - HEATING OF THE PLUGS WHILST CRANKING .............................................. 99 VIII - POSTHEATING OPERATION ............................................................................ 99 IX - ADDITIONAL HEATING ....................................................................................100 X - AIR CONDITIONING COMPRESSOR CUT-OFF ...............................................104 XI - ENGINE IMMOBILISER FUNCTION .................................................................104 XII - DISPLAYING FAULTS: DOWNGRADED MODES OPERATION ......................105 XIII - COOLANT TEMPERATURE WARNING LED (V4020) - FEATURE...................107 XIV - CRUISE CONTROL ..........................................................................................108
F
CONTENTS
CHAPTER 13: OPERATING PHASES: PARTICLE FILTRATION ........ 109 I - GENERAL PRINCIPLE ...................................................................................... 109 II - DIAGRAM .......................................................................................................... 110 III - PARTICLE FILTER LOAD LEVEL MONITORING FUNCTION .......................... 112 IV - REGENERATION ASSISTANCE MANAGEMENT FUNCTION ......................... 116 V - EFFECTS OF ACTIVATING REGENERATION ASSISTANCE .......................... 120 VI - FUEL ADDITIVE FUNCTION ............................................................................ 125 VII - DISPLAYING FAULTS - DOWNGRADED OPERATING MODES ..................... 127 VIII - DRIVER'S INFORMATION FUNCTION ............................................................ 129
CHAPTER 14: MAINTENANCE: HDI INJECTION SYSTEM ................. 131 I - RECOMMENDED FUEL .................................................................................... 131 II - SAFETY INSTRUCTIONS.................................................................................. 132 III - MAINTENANCE ................................................................................................ 135 IV - REPLACING PARTS: OPERATIONS TO BE PERFORMED ............................. 137 V - WARRANTY RETURN PROCEDURE................................................................ 140
CHAPTER 15: WIRING DIAGRAM ......................................................... 141 I - LAYOUT DIAGRAM ........................................................................................... 141 II - PARTS LIST ...................................................................................................... 142
1
Chapter 1
GENERAL DETAILS:
HDI DIRECT INJECTION SYSTEM
Note: Some items mentioned in this document are common to the brochure: "HDI
injection system" (doc 1.6.159). Reference should be made to this
document where necessary.
Note: All values specified in this document are given as guidelines only. Refer to
the documentation corresponding to the vehicle.
I - FOREWORD
The HDI system fitted to the new DW12 TED4 engine is based on the system
fitted to the DW10 engine and includes the following additional features:
, cylinder head with 16 valves (4 valves/cylinder),
, double complex shape air inlet ducts in the cylinder head (variable swirl),
, variable geometry turbocharger
The HDI system is used to fulfil the requirements of the current standards
regarding the following:
, depollution,
, driving pleasure,
, fuel saving,
, mechanical reliability.
In addition to these features, a powerful pollutant particle filtration system has
been developed.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
2
Chapter 1
A - DEPOLLUTION
Fuel combustion causes the emission of the following pollutants: , carbon dioxide (CO2),
, carbon monoxide (CO),
, unburned hydrocarbons (HC),
nitrogen oxide (NOx), ,
, carbon particles.
Antipollution regulations are being tightened up and lead to the following developments:
, installation of an exhaust gas recycling device (EGR) to reduce nitrogen oxide emissions (NOx) (water cooled),
, installation of a throttle housing (EGR) to improve exhaust gas recycling. Fitting a catalytic converter reduces the following pollutants: , carbon monoxide (CO),
, unburned hydrocarbons (HC),
, carbon particles.
Fitting a 16 valve cylinder head reduces the following pollutants: , nitrogen oxides (NOx),
, carbon particles.
The dual intake air inlet ducts in the cylinder head help to reduce pollutant particles.
The filter system removes black smoke and pollutant particles at full load or during transitory operation, thus helping to protect the environment.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
3
Chapter 1
B - MAIN DESIGN OF THE DW12 TED4 ENGINE
Up until now, diesel engines fitted to touring cars have used indirect injection. In indirect injection, the fuel is injected under a maximum pressure of 300 bar into a combustion prechamber.
In direct injection, the fuel is injected directly onto the top of the piston. Engine efficiency is improved due to:
, better quality of the air/fuel mixture,
, reduction in heat losses,
, direct combustion in the cylinders.
Features of the new cylinder head design of the DW12 TED4 engine: , cylinder head with 16 valves,
, specific location of the diesel injectors (central and vertical, optimisation of air/fuel mixture),
, double complex shape air inlet manifolds in the cylinder head (variable swirl),
, no precombustion chamber,
, specific location of the heater plugs (on the rear of the cylinder head). Modifications used to improve the efficiency of the DW12 TED4 engines: , variable geometry turbocharger (higher turbocharging pressure at low engine speeds),
, optimisation of the inlet and exhaust manifolds,
, roller valve rockers limiting losses caused by friction,
, weight reduction.
Note: The above modifications also help to reduce pollutant emissions
directly.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
4
Chapter 1
II - PRINCIPLE OF HDI
The device, developed in collaboration with BOSCH, is used to work out an ideal injection law.
Injection is performed at very high pressure using an injection rail which is common to the electrohydraulic injectors (called common rail). The common injection rail is maintained at a very high pressure. The injection pressure may reach 1350 bar at high engine speed. The injection ECU integrates the following parameters:
, engine speed,
, coolant temperature,
, air temperature,
, fuel temperature,
, fuel pressure,
, pressure in the inlet manifold,
, atmospheric pressure,
, position of the accelerator pedal,
, air flow.
The injection ECU:
, works out the injection time from the fuel pressure,
, controls, if necessary, a pre-injection (to reduce combustion noise) and the main injection,
, controls the fuel flow injected by the electrohydraulic injectors. Advantages of the electronic management system:
, driving pleasure (50% additional torque at low engine speeds and 25% more power),
, increase in engine efficiency (around 20% fuel saving), , reduction of pollutant emissions (CO2, CO, HC, and carbon particles).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
5
Chapter 1
III - PARTICLE FILTRATION PRINCIPLE
The aim of the filtration system is to reduce emissions of particles released into the atmosphere (black smoke released at full load or during transitory operation). A particle filter is fitted on the exhaust pipe and traps the particles as the exhaust gas passes through.
The accumulation of particles whilst the engine is operating leads to the progressive clogging up of the particle filter.
To prevent the particle filter from becoming blocked, it must be "regenerated". A - PARTICLE FILTER REGENERATION PRINCIPLE
Regeneration consists of periodically burning off the particles accumulated in
the particle filter essentially consisting of carbon and hydrocarbons. These
particles on the particle filter burn in the presence of oxygen at a temperature
of 550?C (regeneration limit).
Regeneration of the particle filter is controlled by the injection system.
The injection system triggers an additional injection to increase the initial
temperature of the exhaust gases from approximately 150?C (urban driving) to
450?C at the inlet of the catalytic converter.
This increase in temperature occurs in 2 steps:
, a post injection (after Top Dead Centre) creates a post combustion in the
cylinder and leads to an increase in temperature of 200 - 250?C,
, an additional post combustion, generated by an oxidation catalytic
converter placed upstream of the particle filter, deals with the unburned
hydrocarbons (HC) from the post injection. The temperature increases by
100?C which allows the combustion limit of 550?C to be reached. B - FUEL ADDITIVE FUNCTION
To lower the regeneration limit, Eolys, a cerine based composite, is added to
the fuel which lowers the particle combustion temperature from 550?C to
450?C.
Cerine is used in an organic solution stored in an additional tank, located near
to the fuel tank
In order to inject an amount of additive proportional to the amount of fuel
injected, an additive system has been developed.
The system consists of the following components:
, a suction device with low level detection on the additive tank,
, an additive injection system in the fuel tank,
, a specific ECU controlling the additive function.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
6
Chapter 1
IV - SAFETY INSTRUCTIONS
Note: The safety recommendations are given in a document contained in the
mechanical file of the vehicle in question.
A - FUEL SUPPLY CIRCUIT
IMPORTANT: Given the very high pressures (1350 bar) in the high pressure
fuel circuit, follow these instructions.
Do not smoke near to the high pressure circuit during repairs.
Avoid working near to flames or sparks.
When the engine is running:
, do not work on the high pressure fuel circuit,
, always remain out of the range of a possible jet of fuel which may cause
serious injury,
, never put your hand near to a leak on the high pressure fuel circuit.
After switching off the engine, wait for 30 seconds before starting work.
Note: It is necessary to wait for 30 seconds to allow the high pressure fuel
circuit to return to atmospheric pressure.
For all repair work, it is recommended that gloves and protective goggles are
worn.
B - FUEL ADDITIVE CIRCUIT
Do not smoke near to the fuel additive circuit during repairs.
Avoid working near to flames or sparks.
The additive is a slight skin irritant; it is recommended that gloves and
protective goggles are worn.
Environmental protection: used additive and the components used for
cleaning the filter must be treated.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
7
Chapter 1
C - OPERATIONS ON THE PARTICLE FILTER
Warning: Forced regeneration leads to a very high exhaust gas temperature
(450:C at the exhaust pipe outlet).
Precautions to be taken:
, always keep well away from the exhaust pipe,
use suitable exhaust gas extraction equipment, ,
, the work area must be clean and tidy,
, the vehicle chassis must be clean.
It is recommended that a mask and protective goggles are worn when
removing and refitting the particle filter (risk of inhaling cerine). BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
8
Chapter 1
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
9
Chapter 2
GENERAL LAYOUT:
HDI SYSTEM
11
5
4
32b
58
Key:
A - VAN network
B - CAN network
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
2a
7
6
11
5659
70
10
71
5715
98
12
53
52
16
51
1314
50
33
44
1745
19
18
3447
46
48
29
49
20
3521
42
22
3243
41
36
40
25
3723
2426
30
39
38
31
28
SDI001P
A
27
B
10
Chapter 2
PART NUMBER IN THE WIRING REF. DESCRIPTION DIAGRAMS 1 Additional heating control relay BCP3 2 Additional heating (electric resistors (2a) or 8098 - 1190
heater (2b)) (*)
3 Variable geometry turbocharger -- 4 Air flowmeter / air temperature sensor 1310 5 Air filter -- 6 Catalytic converter -- 7 Particle filter -- 8 Turbocharging pressure regulation 1233
electrovalve
9 Recycling regulation electrovalve (EGR) 1253 10 Variable geometry turbo control diaphragm -- 11 Exhaust gas recycling valve (EGR) -- 12 Exhaust gas / water heat exchanger -- 13 Injection ECU 1320 14 Atmospheric pressure sensor (incorporated 1320
into injection ECU)
15 Electronic stability program ECU (*) 7800 16 Automatic gearbox ECU (*) 1360 17 Trip computer (*) -- 18 Electronic rev counter 4210 19 Preheating LED V1150 20 Diagnostic LED V1300 21 Fan unit 1510 22 Air conditioning compressor 8020 23 Coolant temperature warning LED V4020 24 Coolant temperature gauge 4026 25 Cruise control switch 7300 26 Cruise control safety contact 7305 27 Redundant brake switch 7308 28 Switch module at steering wheel (COM CV00
2000)
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
11
Chapter 2
PART NUMBER IN THE WIRING REF. DESCRIPTION DIAGRAMS 29 Built-in systems interface (BSI) BSI1 30 Central diagnostic socket C001 31 Battery BB00 32 Double injection relay (engine relay unit) BSM 33 Vehicle speed sensor 1620 34 Accelerator pedal position sensor 1261 35 Clutch pedal switch 7306 36 Brake pedal switch 2100 37 Coolant temperature sensor 1220 38 Fuel tank -- 39 Low pressure pump 1211 40 Electric fuel heater 1276 41 Pre-post heating unit 1150 42 Fuel cooling -- 43 Fuel filter -- 44 High pressure fuel pump -- 45 High pressure fuel regulator 1322 46 Fuel temperature sensor 1310 47 High pressure fuel sensor 1321 48 High pressure fuel common injection rail -- 49 Preheater plugs 1160 50 Engine speed sensor 1313 51 Camshaft position sensor 1115
rd52 High pressure fuel pump 3 piston 1277
deactivator
53 Diesel injectors 1331 - 1332 - 1333 - 1334 54 "Swirl" control electrovalve 1264 55 "Swirl" control diaphragm -- 56 Throttle housing control electrovalve (EGR) 1263 57 Throttle housing (EGR) -- 58 Air / air heat exchanger -- 59 Inlet manifold pressure sensor 1312
Note: (*) depending on version.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
12
Chapter 2
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
13
Chapter 4
FUEL SUPPLY FUNCTION
I - DIAGRAM
A
B
C
4
123
235
226
7201821
8
19
9
17
10
SDI002P
1116121315
14
Key:
A - Return to fuel tank circuit B - Low pressure fuel circuit C - High pressure fuel circuit
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
14
Chapter 4
Parts list
PART NUMBER IN THE WIRING REF. DESCRIPTION DIAGRAMS 1 - 4 Diesel injectors (electrohydraulic) 1131 - 1132 - 1133 - 1134 5 High pressure fuel common injection rail -- 6 High pressure fuel sensor 1321 7 Fuel temperature sensor 1221 8 Fuel cooler -- 9 Fuel tank -- 10 Low pressure pump 1211 11 Fuel pre-filter -- 12 Safety valve (pressure-vacuum) -- 13 Additive tank -- 14 Low additive level sensor 1283 15 Additive injection pump 1283 16 Plug (overflow) -- 17 Additive injector 1284 18 Electric fuel heater 1276 19 Water bleed screw -- 20 Fuel filter + water decanter + low --
pressure circuit pressure regulator
21 High pressure fuel pump -- 22 High pressure fuel regulator on the high 1322
pressure fuel pump
rd23 High pressure fuel pump 3 piston 1277
deactivator
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
15
Chapter 4
II - COMPONENTS COMMON WITH DOCUMENT "BOSCH EDC 15C2 HDI
INJECTION SYSTEM"
Common components:
, fuel tank,
, low pressure pump (1211),
, fuel filter (thermostatic element),
, high pressure fuel pump,
rd, high pressure fuel pump 3 piston deactivator (1277),
, high pressure fuel regulator (1322),
, high pressure fuel common injection rail,
, diesel injectors (1131, 1132, 1133, 1134),
, fuel cooler.
Note: The filtration housing is fitted with a water in the fuel detector (4050) (major
export).
III - SPECIFIC COMPONENTS
Specific features of the DW12 TED4 engine:
, electric fuel heater (1276),
, high pressure fuel pump with blue supplier's plate. BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
16
Chapter 4
IV - ELECTRIC FUEL HEATER (1276)
A - ROLE
The fuel heater raises the fuel to its usage temperature. B - DESCRIPTION
21SDI003C
The fuel heater heats the fuel from the fuel tank.
The fuel heater consists of a heating resistor.
The temperature is regulated by a thermostat:
, fuel temperature of -2 (+/-2):C: fuel heater activated,
, fuel temperature of +3 (+/-2):C: fuel heater deactivated. C - ELECTRIC FEATURES
Allocation of connector channels:
, channel 1: 12 volts (+ ignition on),
, channel 2: earth.
Power: 150 W.
D - LOCATION
The fuel heater is located on the fuel filter inlet pipe.
V - LOW PRESSURE PUMP SUPPLY CUT-OFF
The airbag ECUs incorporate the low pressure pump cut-off function (inertia
switch discontinued).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
17
Chapter 4
AIR SUPPLY FUNCTION
I - DIAGRAM
5
6
41
2
7
327
24a25
9828
26
22
21b23
19
20
10A
11B12C131615141817
SDI004P
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
18
Chapter 4
Air circulation (following arrows): A - Exterior air inlet
B - Exhaust gases + air
C - Exhaust gases
a - Short inlet duct (helical shape)
b - Long inlet duct (tangential) Parts list:
PART NUMBER IN REF. DESCRIPTION THE WIRING COMMENTS
DIAGRAMS
1 Throttle housing control 1263
electrovalve (EGR)
2 "Swirl" control electrovalve 1264 3 "Swirl" control diaphragm -- Vacuum controlled 4 Recycling regulation 1253
electrovalve (EGR)
5 Vacuum pump -- 6 Vacuum reserve -- 7 Exhaust gas recycling valve -- Vacuum controlled
(EGR)
8 Turbocharging pressure 1233
regulation electrovalve
Exhaust gas manifold -- 9
10 Inlet air heater throttle control 1285
electrovalve
11 Variable geometry turbo control -- Vacuum controlled
diaphragm
12 Finned diffuser piston -- 13 Particle filter + catalytic --
converter
14 Exhaust turbine -- 15 Variable geometry turbocharger -- 16 Inlet air turbine -- 17 Air flowmeter + air temperature 1310
sensor
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
19
Chapter 4
PART NUMBER IN
REF. DESCRIPTION THE WIRING COMMENTS
DIAGRAMS
18 Air filter --
19 Air/air heat exchanger --
20 Air/water heat exchanger (inlet --
air heater)
21 Inlet manifold pressure sensor 1312
22 Inlet air heater throttle -- Vacuum controlled
23 "Swirl" control throttle --
24 Inlet air manifold --
25 Exhaust gas/coolant exchanger --
26 Throttle housing (EGR) -- Vacuum controlled
27 Injection ECU 1320
28 Atmospheric pressure sensor 1320
(incorporated into injection
ECU)
Note: EGR: exhaust gas recycling.
Turbocharging pressure regulation electrovalve:
White/grey referenced hose opposite white spot on electrovalve
Swirl control electrovalve:
Unmarked hose
EGR regulation electrovalve:
White/blue referenced hose opposite white spot on electrovalve
EGR throttle housing control electrovalve:
White/black referenced hose opposite white spot on electrovalve
Inlet air heater throttle control electrovalve:
White/brown referenced hose opposite white spot on electrovalve
Inlet air heater throttle:
Brown capsule - brown referenced hose EGR throttle housing:
Black capsule - black referenced hose BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
20
Chapter 4
II - COMPONENTS COMMON WITH DOCUMENT "BOSCH EDC 15C2 HDI
INJECTION SYSTEM"
Components common with the document:
, air filter,
, atmospheric pressure sensor (1320),
, air/air heat exchanger,
, inlet manifold pressure sensor (1312),
, vacuum pump,
, turbocharging pressure regulation electrovalve (1233).
III - SPECIFIC COMPONENTS
Specific features of the DW12 TED4 engine:
, vacuum reserve,
, variable geometry turbocharger,
, variable "swirl",
, "Swirl" control electrovalve (1264). BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
21
Chapter 4
IV - VACUUM RESERVE
A - ROLE
The vacuum reserve allows sufficient braking assistance to be maintained if
the following components are controlled simultaneously:
, "Swirl" control butterfly valve,
, inlet air heater butterfly valve,
, variable geometry turbo control diaphragm. B - DESCRIPTION
c
SDI005C
ed
c - Vacuum pump vacuum inlet
d - Outlet: "Swirl" control butterfly valve
e - Outlet: variable geometry turbo control diaphragm
Capacity = 0.5 Litre
C - LOCATION
The vacuum reserve is located in the engine compartment, near to the brake
servo (depending on vehicle).
Note: The vacuum circuit contains 3 nozzles of 0.55 mm.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
22
Chapter 4
V - VARIABLE GEOMETRY TURBOCHARGER
A - ROLE
The turbocharger is used to turbocharge the air entering the engine.
The variable geometry turbocharger is used:
, to increase the speed of the exhaust gases which strike the turbine at low
engine speeds,
, to reduce the speed of the exhaust gases which strike the turbine at high
engine speeds,
to adapt the turbine to a variation in exhaust gas flow. ,
B - DESCRIPTION
14f
16
11
29
g
SDI006D1612
14
11 - Finned diffuser piston control diaphragm: vacuum controlled
12 - Finned diffuser piston
14 - Exhaust turbine
16 - Inlet air turbine
29 - Thermal housing
f - Gases from the exhaust manifold
g - To inlet manifold
The turbocharger has two separate chambers.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
23
Chapter 4
The turbocharger consists of the following components:
, a chamber linked to the engine exhaust function,
, a chamber linked to the inlet function,
, a turbine and a compressor, joined together by a shaft.
The turbine, driven by the exhaust gases, drives the compressor which compresses the inlet air.
The movement of the piston (12) allows the inlet cross section of the exhaust turbine to be varied in order to alter the speed of the exhaust gases. The regulation electrovalve controls the turbocharging pressure regulator piston (12).
The turbocharging pressure is regulated progressively and is controlled by a cartographic map (injection ECU).
Note: Lubrication of the turbocharger: careful lubrication is required due to
the very high speeds of the moving parts and the high temperatures to
be dissipated.
The pressurised oil required for this function is taken from the engine's oil circuit.
IMPORTANT: Before switching off the engine, it is essential to let the engine
return to idle speed. Failure to comply with this condition will
eventually destroy the turbocharger (due to lack of
lubrication).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
24
Chapter 4
C - OPERATION AT LOW ENGINE SPEED
12
SDI007D
14
The gas flow passing through the exhaust turbine (14) is low.
To increase the turbocharging pressure, a maximum amount of energy must
be converted in the turbine.
The exhaust gases must be made to pass through a small cross section: the
finned diffuser piston (12) is closed.
Note: The finned diffuser piston is closed when it is not controlled
pneumatically.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
25
Chapter 4
D - OPERATION AT HIGH ENGINE SPEED
12
SDI008D
14
Turbocharging pressure regulation: the energy of the exhaust gases is
controlled by adjusting the speed at which the gases enter the exhaust turbine
by altering the position of the finned diffuser piston.
Contrary to a fixed geometry turbocharger, all of the exhaust gas flow passes
through the exhaust turbine (no energy lost).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
26
Chapter 4
VI - VARIABLE "SWIRL"
a
b
SDI009C
a - Short inlet duct (helical shape)
b - Long inlet duct (tangential)
Using the short inlet duct allows maximum swirl to be obtained (swirl movement).
Air is let into the inlet ducts by opening the "Swirl" control butterfly valve at high
engine speeds.
Using 2 inlet ducts allows maximum filling (reduced swirl). Advantages of the variable "Swirl":
optimisation of combustion (air/fuel mixture), ,
, better performance/pollutant emissions compromise. The variable "Swirl" gives a reduction in carbon particles. BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
27
Chapter 4
VII - SWIRL CONTROL ELECTROVALVE (1264)
A - ROLE
The Swirl control electrovalve controls the Swirl control diaphragm. B - DESCRIPTION
The control electrovalve connects the vacuum pump and the Swirl control
diaphragm.
h
l
jkSDI010C
h - Vacuum inlet from the vacuum reserve
j - Atmospheric pressure inlet
k - Electrical connector
l - "Usage" outlet
The electrovalve is controlled with an OCR (Open Cycle Ratio) and using a
cartographic map (injection ECU).
The electrovalve is subject to the following:
atmospheric pressure, ,
, vacuum supplied by the vacuum pump.
The pressure supplied by the electrovalve is between atmospheric pressure
and the vacuum from the vacuum pump.
Warning: The "Swirl" control throttle is closed when it is not controlled
pneumatically.
Conditions allowing the throttle to open:
, engine speed above 2100 rpm (at 80:C) (2500 rpm at 0:C),
, injected fuel flow greater than 40 mg/stroke.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
28
Chapter 4
C - ELECTRICAL FEATURES
Control: injection ECU (earth).
Full supply (maximum OCR) = maximum vacuum.
No supply (minimum OCR) = no vacuum (atmospheric pressure).
Resistance at 25 :C = 28 ohms.
D - LOCATION
The Swirl control electrovalve is located on the coolant outlet housing.
VIII - FEATURE: INLET MANIFOLD PRESSURE SENSOR (1312)
SDI011C
The inlet manifold pressure sensor is located on the outlet of the air/air heat
exchanger.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
29
Chapter 5
EXHAUST GAS RECYCLING FUNCTION
I - DIAGRAM
5
6
41
2
7
327
24a25
9828
26
22
21b23
19
20
10A
11B12C131615141817
SDI004P
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
30
Chapter 5
Air circulation (following arrows): A - Exterior air inlet
B - Exhaust gases + air
C - Exhaust gases
a - Short inlet duct (helical shape)
b - Long inlet duct (tangential) Parts list:
PART NUMBER IN REF. DESCRIPTION THE WIRING COMMENTS
DIAGRAMS
1 Throttle housing control 1263
electrovalve (EGR)
2 "Swirl" control electrovalve 1264 3 "Swirl" control diaphragm -- Vacuum controlled 4 Recycling regulation 1253
electrovalve (EGR)
5 Vacuum pump -- 6 Vacuum reserve -- 7 Exhaust gas recycling valve -- Vacuum controlled
(EGR)
8 Turbocharging pressure 1233
regulation electrovalve
Exhaust gas manifold -- 9
10 Inlet air heater throttle control 1285
electrovalve
11 Variable geometry turbo control -- Vacuum controlled
diaphragm
12 Finned diffuser piston -- 13 Particle filter + catalytic --
converter
14 Exhaust turbine -- 15 Variable geometry turbocharger -- 16 Inlet air turbine -- 17 Air flowmeter + air temperature 1310
sensor
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
31
Chapter 5
PART NUMBER IN REF. DESCRIPTION THE WIRING COMMENTS
DIAGRAMS
18 Air filter -- 19 Air/air heat exchanger -- 20 Air/water heat exchanger (inlet --
air heater)
21 Inlet manifold pressure sensor 1312 22 Inlet air heater throttle -- Vacuum controlled 23 "Swirl" control throttle -- 24 Inlet air manifold -- 25 Exhaust gas/coolant exchanger -- 26 Throttle housing (EGR) -- Vacuum controlled 27 Injection ECU 1320 28 Atmospheric pressure sensor 1320
(incorporated into injection
ECU)
Note: EGR: exhaust gas recycling.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
32
Chapter 5
II - COMPONENTS COMMON WITH DOCUMENT "BOSCH EDC 15C2 HDI
INJECTION SYSTEM"
Components common with the document:
, air flowmeter (1310),
, exhaust gas recycling valve (EGR),
, recycling regulation electrovalve (EGR) (1253). III - SPECIFIC COMPONENTS
Specific features of the DW12 TED4 engine:
, water/exhaust gas exchanger (EGR),
, recycling regulation electrovalve (EGR) (1253),
, throttle housing (EGR),
, throttle housing control electrovalve (EGR) (1263). IV - WATER/EXHAUST GAS EXCHANGER (EGR)
A - ROLE
The water/exhaust gas heat exchanger cools the recycled exhaust gases let
into the cylinders.
B - LOCATION
Location: on the rear of the cylinder head (bulkhead side). V - THROTTLE HOUSING (EGR)
A - ROLE
In addition to the EGR valve, the throttle housing, depending on its position, is
used to improve exhaust gas recycling. The throttle housing is controlled
progressively and using a cartographic map (injection ECU).
Warning: The throttle housing is open when it is not controlled
pneumatically.
B - LOCATION
The throttle housing is located at the inlet to the inlet manifold. BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
33
Chapter 5
VI - THROTTLE HOUSING CONTROL ELECTROVALVE (EGR) (1263) A - ROLE
The electrovalve controls the closing of the throttle housing. B - DESCRIPTION
The electrovalve is the same as the following electrovalves:
, turbocharging pressure regulation electrovalve,
, recycling regulation electrovalve (EGR),
, inlet air heater throttle control electrovalve.
The electrovalve connects the vacuum pump to the throttle housing:
, the greater the vacuum, the more the throttle housing closes,
, the lower the vacuum, the more the throttle housing opens. C - LOCATION
1
SDI012C
The electrovalve is located in the engine compartment. BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
34
Chapter 5
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
35
Chapter 6
HDI SYSTEM
I - COMPONENTS COMMON WITH DOCUMENT "BOSCH EDC 15C2 HDI
INJECTION SYSTEM"
Components common with the document: , high pressure fuel pump,
, high pressure fuel pump 3rd piston deactivator (1277),
, high pressure fuel regulator (1322), , high pressure fuel common injection rail, , battery (BB00),
, double injection relay (1304),
, accelerator pedal sensor (1261), , engine speed sensor (1313),
, camshaft position sensor (1115), , coolant temperature sensor (1220), , air temperature sensor (1310),
, fuel temperature sensor (1221), , high pressure fuel sensor (1321), , vehicle speed sensor (1620),
, brake switch (2100),
, specific feature of the diesel injector control.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
36
Chapter 6
II - SPECIFIC COMPONENTS
Specific features of the DW12 TED4 engine:
, injection ECU (1320),
, diesel injectors (1331, 1332, 1333, 1334). III - DOUBLE INJECTION RELAY (BSM) - FEATURE
The double relay is incorporated into the engine relay unit (BSM).
SDI013C
1
1 - Double relay
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
37
Chapter 6
IV - COOLANT TEMPERATURE SENSOR (1220) - FEATURE
A - ROLE
The coolant temperature sensor informs the ECU of the temperature of the
engine coolant.
Role of the injection ECU depending on the information received:
, to adjust the preheating time,
, to adjust the post-heating time,
, to adjusting the starting flow,
, to adjust the idle speed,
, to authorise exhaust gas recycling (EGR),
, to adjust the fuel flow,
, to limit the injected flow if the coolant temperature is critical (anti-boil
function),
, to control the operation of the radiator fans,
, to control the coolant temperature gauge on the instrument panel (*),
, to control the warning and pre-warning LEDs (*).
Note: (*) depending on version.
B - DESCRIPTION
Green 2-way sensor.
The sensor consists of a Negative Temperature Coefficient resistor (NTC).
The higher the temperature, the lower its resistance.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
38
Chapter 6
C - LOCATION
SDI014C2
2 - coolant temperature sensor.
The coolant temperature sensor is located on the coolant housing.
There are 2 types of assembly.
Metal coolant outlet housing.
, the coolant temperature sensor is screwed in,
, it is sealed by a copper seal.
Plastic coolant outlet housing:
, the temperature sensor is secured by a plastic clip,
, it is sealed by an O-ring.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
39
Chapter 6
V - FUEL TEMPERATURE SENSOR (1221) - FEATURE
A - ROLE
Role of the injection ECU depending on the information received:
, to adjust the fuel flow,
, to calculate the fuel density.
B - DESCRIPTION
3
SDI015C
3 - Fuel temperature sensor
The sensor consists of a Negative Temperature Coefficient resistor (NTC).
The higher the temperature, the lower its resistance:
, resistance at 20 :C = 3323 ohms,
, resistance at 80 :C = 287 ohms.
C - LOCATION
The fuel temperature sensor measures the temperature of the fuel directly on
the tank return circuit.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
40
Chapter 6
VI - BRAKE SWITCH (2100) - FEATURE
A - ROLE
The switch allows the injection ECU to ensure correct driving comfort.
The electrical information supplied by the brake switch is transmitted to the
BSI and sent to the injection ECU via the multiplexed network (*).
(*) depending on version.
B - LOCATION
The brake switch is located on the pedal set.
VII - CRUISE CONTROL BRAKE PEDAL SWITCH (7308) - FEATURE
A - ROLE
The switch allows the injection ECU to ensure correct driving comfort.
The information from the brake switches is constantly compared with each
other in order to detect any faults.
B - LOCATION
The brake switch is located on the pedal set.
VIII - CLUTCH SWITCH (7306) - FEATURE
A - ROLE
The clutch switch allows the injection ECU to perform the driven idle function.
B - LOCATION
The clutch switch is located on the pedal set.
IX - VEHICLE SPEED SENSOR - FEATURE
The vehicle speed information is transmitted by the ABS ECU on the multiplexed
networks.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
41
Chapter 6
X - INJECTION ECU (1320) - FEATURE
A - ROLE
The ECU controls all of the injection system. The ECU software incorporates:
, the functions for controlling injection and depollution, , the driving pleasure strategies,
, the engine immobiliser function,
, the emergency strategies,
, control of the fan units and warning LEDs (*), , control of the coolant heating systems for the heater matrix (*),
, diagnostics with fault memorising,
, the cruise control function (*),
, the dialogue with all ECUs of the multiplexed networks. Note: (*) depending on version.
The ECU electrically operates the following components: , diesel injectors,
, turbocharging pressure regulation electrovalve, , high pressure fuel regulator,
, recycling regulation electrovalve,
, pre and post heating unit (post-heating cut-out)
rd, high pressure fuel pump 3 piston deactivator.
The ECU supplies the following information: , engine speed: to the instrument panel dials , instant consumption: to the trip computer, , air conditioning cut-off,
, coolant heater operation authorisation (depending on version).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
42
Chapter 6
The atmospheric pressure sensor cannot be removed from the injection ECU.
The ECU has a power stage which is capable of providing the very high
control current required for the injectors to operate. The ECU is connected to the injection harness by an 88 track connector.
The injection ECU software is upgraded by downloading (ECU with a flash
EPROM).
B - ALLOCATION OF ECU CHANNELS
CHANNEL N? DESCRIPTION
1 +12 V supply (after double relay) (engine relay unit)
2 Injector n?1 control
3 Injector n?3 control
4 Injector n?4 control
5 Injector n?2 control
6 Injector n?2 control
7 -
8 Diagnostic line for the coils of the fan unit control relays
9 Dialogue line: CAN H network
10 -
11 Input: air temperature sensor (flowmeter)
12 Supply: camshaft position sensor / differential pressure
sensor
13 Input: air flow signal (flowmeter)
14 Input: engine speed sensor signal
15 Input: accelerator pedal sensor signal
16 -
17 -
18 Input: camshaft sensor signal
19 -
20 -
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
43
Chapter 6
DESCRIPTION CHANNEL N:
21 Input: clutch switch
22 Sensors earth
23 ---
24 Output: Swirl control electrovalve 25 Output: fan unit 1 control (high speed) 26 Output: turbocharging pressure regulation electrovalve
27 Earth: differential pressure sensor 28 Output: inlet air heater throttle control electrovalve
29 +12 volts supply (after double relay) (engine relay unit)
30 Injector N: 1 control
31 Injector N: 3 control
32 Injector N: 4 control
33 Earth
34 Sensors earth
35 ---
36 Engine immobiliser serial line (*) 37 Dialogue line: CAN L network 38 K diagnostic line
39 Input: fuel temperature sensor 40 Earth: camshaft position sensor 41 Input: engine speed sensor signal 42 Input: differential pressure sensor 43 ---
44 Sensors supply (5 volts)
45 Earth: coolant temperature sensor 46 Input: coolant temperature information 47 ---
48 Stop lamps contact
49 Earth
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
44
Chapter 6
DESCRIPTION CHANNEL N:
50 ---
51 Earth
52 Output: recycling electrovalve control (EGR) 53 Earth
54 ---
55 Output: throttle housing electrovalve control (EGR)
56 ---
57 Output: fan unit control: mid speed (*) 58 Output: additional heating control 1 59 ---
60 Output: high pressure fuel regulator 61 ---
62 ---
63 ---
64 ---
65 ---
66 ---
67 Input: preheater unit diagnostic 68 Input: accelerator pedal sensor 69 + ignition on: engine relay unit (BSM) 70 Input: exhaust gas temperature sensor (upstream of the
catalytic converter)
71 Input: inlet manifold air pressure 72 ---
73 Input: redundant brake switch 74 Input: fuel pressure
75 Air conditioning pressurestat (26 bar control stage)
76 ---
77 ---
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
45
Chapter 6
DESCRIPTION CHANNEL N:
78 ---
79 ---
80 Output: high pressure fuel pump 3rd piston deactivator
81 ---
82 ---
83 Output: fan unit control 2 (low speed)
84 ---
85 Output: additional heating control 2
86 Output: double relay control (engine relay unit)
87 Input: inertia switch (earthing)
88 Output: preheating unit control Note: (*) depending on version.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
46
Chapter 6
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
47
Chapter 7
PRE-POST HEATING FUNCTION
I - COMPONENTS COMMON WITH DOCUMENT "BOSCH EDC 15C2 HDI
INJECTION SYSTEM"
Components common with the document:
, preheater plugs (1160),
, pre-post heating unit (1150).
II - PREHEATER PLUGS (1160) - FEATURE
The preheater plugs are located on the cylinder head, on the rear of the engine
(bulkhead side).
The preheater plugs can be activated during particle filter regeneration assistance.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
48
Chapter 7
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
49
Chapter 8
ENGINE COOLING FUNCTION (FRIC)
(INCORPORATED INTO THE INJECTION ECU) The injection ECU performs the following functions:
, it switches the fan units on and off (engine cooling),
, it controls post ventilation (for 6 minutes maximum),
, it illuminates the coolant temperature warning LED on the instrument panel, , it controls the coolant temperature gauge on the instrument panel, , it performs diagnostics for fan unit operation,
, it acquires the engine coolant temperature,
, it manages downgraded modes.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
50
Chapter 8
I - DIAGRAM
2
1360800713203
1510
1
58020
74
BSI1V130012206
0004A
B
CC00180804026V4020SDI025D
Key:
A - VAN network
B - CAN network
C - Wire connection
PART NUMBER IN THE WIRING DESCRIPTION DIAGRAMS Automatic gearbox ECU (*) 1360 Diagnostic LED V1300 Fan unit 1510 Air conditioning compressor 8020 Control panel (logometer + warning LED on 0004 the control panel
Coolant temperature warning LED V4020 Coolant temperature logometer 4026 Built-in systems interface BSI1 Central diagnostic socket C001 Injection ECU 1320 Air conditioning ECU 8080 Air conditioning pressurestat 8007 Coolant temperature sensor 1220 Note: (*) depending on version.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
51
Chapter 8
CONNECTIONS
CONNECTION N? SIGNAL SIGNAL NATURE 1 Coolant temperature sensor Frequency 2 Request for automatic gearbox oil CAN
temperature cooling (*)
3 Fan unit relay control: low speed (1508) All or nothing
Fan unit relay control: high speed (1509) All or nothing 4 Air conditioning compressor control All or nothing 5 Request to illuminate diagnostic LED CAN
Request to illuminate coolant temperature CAN
logometer
Request to illuminate coolant temperature CAN
warning LED
Authorisation to engage the air CAN
conditioning compressor (AC/OUT)
6 Request to illuminate diagnostic LED VAN
Request to illuminate coolant temperature VAN
logometer
Request to flash coolant temperature VAN
warning LED
7 Request to authorise engaging of the air CAN
conditioning compressor (AC/TH)
Note: (*) depending on vehicle equipment.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
52
Chapter 8
II - FAN UNIT (1510)
+ig on
+BAT
+BAT
BSM
1508
1514
1509
1320
SDI026C
1510 BSI1 +BAT = + battery
+ig on = + ignition on
BSM - Double injection relay 1514 - Fan unit relay at mid speed There is only one type of assembly: three speed fan unit.
Warning: The limits for engaging the fan unit depend on the vehicle: refer to the
corresponding documentation. There are three operating speeds: , low speed = 97:C,
, mid speed,
, high speed = 105:C.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
53
Chapter 8
A - DESCRIPTION
Low speed is obtained by supplying the fan unit through a resistor arranged in
series on the supply circuit.
Mid speed is obtained by supplying the fan unit through 2 resistors arranged
in parallel in the supply circuit:
- the low speed relay is controlled by the injection ECU,
- the mid speed relay is controlled by the built-in systems interface,
- high speed is obtained by supplying the fan unit directly.
Before switching to high speed, the fan unit is operated at low speed for 3
seconds.
Before switching to mid speed, the fan unit is operated at low speed for 3
seconds (*).
(*) refer to the procedure: cooling requirements for the air conditioning
(BRAC).
B - ELECTRICAL RESISTORS
SDI027C
The 2 resistors are located on the front panel, near to the air/air exchanger
and the fan unit.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
54
Chapter 8
III - COOLANT TEMPERATURE SENSOR (1220)
The coolant temperature sensor informs the ECU of the temperature of the engine
coolant.
The coolant temperature sensor is located on the coolant housing. IV - POST VENTILATION
When the engine is switched off, the ECU controls post ventilation if the coolant
temperature exceeds a certain limit (*) (105:C).
(*) depending on vehicle
Post ventilation occurs at low speed and lasts for a maximum of 6 minutes after
the engine is switched off.
V - DOWNGRADED MODE
Role of the injection ECU when the coolant temperature sensor is faulty:
, to control operation of the fan unit at high speed,
, to control the flashing of the coolant temperature warning LED on the control
panel (depending on version),
, to prevent the air conditioning compressor from being engaged (AC/OUT).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
55
Chapter 9
COOLING REQUIREMENTS FOR THE AIR
CONDITIONING (BRAC)
(INCORPORATED INTO THE INJECTION ECU) Functions of the injection ECU:
, to operate the fan units (air conditioning condenser cooling), , to acquire the pressure of the air conditioning circuit, , to manage downgraded modes.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
56
Chapter 9
I - DIAGRAM
Key:
A - VAN network
B - CAN network
C - Wire connection
PART NUMBER IN THE WIRING DESCRIPTION DIAGRAMS
Automatic gearbox ECU (*) 1360
Diagnostic LED V1300
Fan unit 1510
Air conditioning compressor 8020
Instrument panel 0004
Coolant temperature warning LED V4020
Coolant temperature gauge 4026
Built-in systems interface BSI1
Central diagnostic socket C001
1360Injection ECU 1320
Air conditioning ECU 8080
Air conditioning pressurestat 8007
Coolant temperature sensor 1220
Note: (*) depending on version.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
1
80071320
2
1510
3
8020
6
7
4
BSI1
V1300
1220
5
0400
A
B
C
SDI028D
C00180804026V4020
57
Chapter 9
CONNECTIONS
CONNECTION N? SIGNAL SIGNAL NATURE
1 Air conditioning pressurestat Analogue
2 Fan unit relay control: low speed (1508) All or nothing
Fan unit relay control: high speed (1509) All or nothing
3 Fan unit relay control: mid speed (1514) All or nothing
4 Air conditioning compressor control All or nothing
5 Request to illuminate diagnostic LED VAN
6 Request to illuminate diagnostic LED CAN
Authorisation to engage air conditioning CAN compressor (AC/OUT)
Air conditioning pressurestat CAN
7 Request authorisation to engage air CAN
conditioning compressor (AC/TH)
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
58
Chapter 9
II - AIR CONDITIONING PRESSURESTAT (8007)
A - ROLE
The sensor measures the value of the pressure in the air conditioning circuit.
Role of the injection ECU depending on the information received:
, to authorise operation of the fan unit (air conditioning condenser cooling),
, to authorise engaging of the air conditioning compressor.
B - DESCRIPTION
SDI029C
The sensor is of piezo-electric type.
The sensor consists of strain gauges.
The linear sensor supplies a voltage proportional to the pressure in the air
conditioning circuit.
Identification: black connector.
Note: The electrical information provided by the sensor is transmitted by wire
to the injection ECU, and sent to the built-in systems interface via the
multiplexed network.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
59
Chapter 9
C - ELECTRICAL FEATURES
Allocation of connector channels:
, channel 1: 5 volts supply,
, channel 2: pressure information (0 - 5 volts),
, channel 3: earth.
Voltage supplied for a pressure of 1 bar: + 0.5 volt.
Voltage supplied for a pressure of 31 bars: + 4.5 volts. D - LOCATION
The sensor is located on the air conditioning condenser. BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
60
Chapter 9
III - FAN UNIT (1510)
The ECU controls operation of the fan unit at low speed if the pressure is greater
than 10 bars (off if the pressure is less than 7 bars).
The ECU controls operation of the fan unit at high speed if the pressure is greater
than 22 bars (off if the pressure is less than 19 bars).
Note: The BSI controls operation of the fan unit at mid speed if the pressure is
greater than 17 bars (off if the pressure is less than 14 bars). IV - DOWNGRADED MODE
Role of the injection ECU if the pressurestat develops a fault:
, to control the illumination of the diagnostic LED on the control panel,
, to prevent operation of the air conditioning compressor (AC/OUT).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
61
Chapter 10
PARTICLE FILTER FUNCTION
I - DIAGRAM
11
2b
A
45
2a
Key:
A - VAN network
B - CAN network
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
B
3
7
74
6
15
14
76
16
73
13
75
870
12
11
71
72
9
10
17
20
6121
69
68
18
19
22
6053
67
66
23
24
54
26
65
25
27
64
62
28
63
59
33
55
52
57
50
58
31
56
45
29
51
32
30
46
40
44
49
48
47
42
34
3839
41
43
35
36
37
SDI016P
62
Chapter 10
PART NUMBER IN THE WIRING REF. DESCRIPTION DIAGRAMS 1 Additional heating control relay BCP3 2 Additional heating (electrical resistors (2a) or 8098 - 1190
heater (2b)) (*)
3 Variable geometry turbocharger -- 4 Air flowmeter / air temperature sensor 1310 5 Air filter -- 6 Catalytic converter -- 7 Particle filter -- 8 Exhaust gas temperature sensor 1343
(downstream of the catalytic converter)
9 Differential pressure sensor 1341 10 Exhaust gas temperature sensor 1344
(upstream of the catalytic converter)
11 Turbocharging pressure regulation electrovalve 1233 12 Recycling regulation electrovalve (EGR) 1253 13 Variable geometry turbo control diaphragm -- 14 Exhaust gas recycling valve (EGR) -- 15 Air/water heat exchanger (inlet air heater) -- 16 Coolant/exhaust gas exchanger (EGR) -- 17 Inlet air heater throttle control electrovalve 1285 18 Atmospheric pressure sensor (incorporated into 1320
the injection ECU)
19 Injection ECU 1320 20 Heated rear screen 8120 21 Electronic stability program ECU (*) 7800 22 Automatic gearbox ECU (*) 1360 23 Trip computer (*) -- 24 Electronic rev counter 4210 25 Service LED (*) -- 26 Preheater LED V1150 27 Diagnostic LED V1300 28 Fuel gauge (*) -- 29 Fan unit 1510
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
63
Chapter 10
PART NUMBER IN THE WIRING REF. DESCRIPTION DIAGRAMS 30 Air conditioning compressor 8020 31 Coolant temperature warning LED V4020 32 Coolant temperature gauge 4026 33 Built-in systems interface BSI1 34 Cruise control switch 7300 35 Cruise control safety contact 7305 36 Redundant brake switch 7308 37 Switch module at the steering wheel (COM2000) CV00 38 Fuel additive ECU 1282 39 Additive tank --- 40 Low additive level sensor 1283 41 Additive injection pump 1283 42 Fuel tank -- 43 Additive injector 1284 44 Low pressure pump 1211 45 Electric fuel heater 1276 46 Coolant temperature sensor 1220 47 Plug (overflow) -- 48 Safety valve --- 49 Fuel filler cap presence sensor (*) 4320 50 Central diagnostic socket C001 51 Battery BB00 52 Double injection relay (engine relay unit) BSM 53 Vehicle speed sensor 1620 54 Accelerator pedal position sensor 1261 55 Clutch pedal switch 7306 56 Brake pedal switch 2100 57 Pre-post heating unit 1150 58 Fuel cooler -- 59 Fuel filter -- 60 Engine speed sensor 1313 61 Camshaft position sensor 1115 62 Preheater plugs 1160
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
64
Chapter 10
PART NUMBER IN THE WIRING REF. DESCRIPTION DIAGRAMS 63 High pressure fuel common injection rail -- 64 High pressure fuel sensor 1321 65 Fuel temperature sensor 1310 66 High pressure fuel regulator 1322 67 High pressure fuel pump -- 68 High pressure fuel pump 3rd piston deactivator 1277 69 Diesel injectors 1331 - 1332 - 1333 - 1334 70 Swirl control electrovalve 1264 71 Swirl control diaphragm -- 72 Inlet air heater throttle -- 73 Throttle housing (EGR) -- 74 Air/air heat exchanger -- 75 Throttle housing control electrovalve (EGR) 1263 76 Inlet manifold pressure sensor 1312 Note: (*) depending on version.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
65
Chapter 10
II - PARTICLE FILTER
A - ROLE
The particle filter traps carbon particles as exhaust gases pass through.
B - DESCRIPTION
d
fe
a
a
c
b
b
SDI017D
a - Carbon particles
b - Cerine
c - Filtered exhaust gases
d - Porous ceramic walls
e - Stainless steel casing
f - Thermal insulator
The particle filter is a porous silicon carbide structure containing channels
arranged so as to force the exhaust gases to pass through the walls.
Components retained in the particle filter:
, carbon particles,
, cerine,
, deposits from the engine oil and engine wear.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
66
Chapter 10
Essentially consisting of carbon and hydrocarbons, these particles attached to
the particle filter burn in the presence of oxygen at a temperature of 550?C
(natural regeneration or assisted with post-injection).
Cerine is an inorganic material which does not burn and is retained in the
particle filter in the form of a solid deposit.
The accumulation of particles during engine operation leads to the
progressive clogging up of the particle filter.
Warning: The particle filter must be replaced or cleaned every 80 000 km
(in order to remove the particles retained in the filter). Refer to the
maintenance section.
C - LOCATION
The particle filter is incorporated into the exhaust pipe (downstream of the
catalytic converter).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
67
Chapter 10
III - CATALYTIC CONVERTER
A - ROLE
The catalytic converter is used to increase the temperature of the exhaust
gases, through post-combustion of the unburned hydrocarbons (HC) resulting
from post-injection.
B - DESCRIPTION
Composition of an oxidation catalytic converter:
, a stainless steel envelope,
, a thermal insulator,
, a ceramic honeycombed monolith impregnated with precious metals.
C - LOCATION
The catalytic converter is located immediately after the particle filter. BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
68
Chapter 10
IV - EXHAUST GAS TEMPERATURE SENSOR (UPSTREAM OF THE CATALYTIC CONVERTER) (1344)
A - ROLE
The temperature sensor informs the injection ECU of the temperature of the
exhaust gases (upstream of the catalytic converter). B - DESCRIPTION
SDI018C
The sensor consists of a Negative Temperature Coefficient resistor (NTC).
The higher the temperature, the lower its resistance. C - ELECTRICAL FEATURES
Allocation of connector channels:
, channel 1: 5 volts,
, channel 2: earth.
Resistance at 100:C = 96 000 ohms.
Resistance at 450:C = 762 ohms.
Warning: The electrical information provided by the upstream temperature
sensor is transmitted directly to the injection ECU. D - LOCATION
The temperature sensor is located upstream of the catalytic converter.
The temperature sensor is screwed onto a base.
IMPORTANT: Use the correct tightening torque.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
69
Chapter 10
V - EXHAUST GAS TEMPERATURE SENSOR (DOWNSTREAM OF THE
CATALYTIC CONVERTER) (1343)
A - ROLE
The temperature sensor informs the injection ECU of the temperature of the
exhaust gases (downstream of the catalytic converter).
B - DESCRIPTION
The downstream temperature sensor is identical to the upstream temperature
sensor.
C - ELECTRICAL FEATURES
Warning: The electrical information provided by the downstream
temperature sensor is transmitted by wire to the additive ECU and
sent to the injection ECU via the multiplexed networks. D - LOCATION
The temperature sensor is located between the catalytic converter and the
particle filter.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
70
Chapter 10
VI - DIFFERENTIAL PRESSURE SENSOR (1341)
A - ROLE
The sensor permanently measures the pressure difference of the exhaust
gases, between the inlet and the outlet of the particle filter, to determine the
status of the filter (clogging problems or damage to filter). B - DESCRIPTION
SDI019Dh
gj
REF
k
lHI
g - HI: Particle filter upstream information input (diameter 4.32 mm)
h - REF: Particle filter downstream information input (diameter 4.32 mm)
j - White marking
k - Electrical connector
l - Membrane
The sensor comprises the following components:
, electronics for amplifying the signal,
, a sealed membrane.
The membrane is subject to the following pressures:
, the inlet pressure of the particle filter (upstream),
, the outlet pressure of the particle filter (downstream).
The sensor provides a voltage proportional to the pressure differential
measured by the membrane (pressure differential = upstream pressure -
downstream pressure).
IMPORTANT: Do not invert the upstream and downstream information pipes
(malfunction of the filtration system). Management of the
particle filter depends on this information.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
71
Chapter 10
C - ELECTRICAL FEATURES
Allocation of connector channels:
, channel 1: pressure information (0.5 - 5 volts),
, channel 2: earth,
, channel 3: 5 volts supply
Voltage supplied for a pressure differential of 0 bar: + 0.5 volt (engine off).
Voltage supplied for a pressure differential of 0.9 bar: + 4.1 volts (particle filter
clogged).
D - LOCATION
9
j
SDI020C
j - white marking
The sensor (9) is located in the centre of the bulkhead at the top (depending
on vehicle).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
72
Chapter 10
VII - AIR TEMPERATURE SENSOR (1310)
The air temperature sensor informs the ECU of the temperature of the inlet air.
Warning: The air temperature sensor is incorporated into the air flowmeter.
Role of the injection ECU depending on the information received:
, to regulate the temperature of the inlet air by operating the inlet air heater
throttle control electrovalve.
Note: When the air temperature sensor (1310) is faulty, the ECU uses a
replacement value of 50:C.
Note: The information from the exterior air temperature sensor (6415) located in
the door mirror is used by the ECU to perform comparison tests. The
exterior air sensor is controlled by the front RH door station (9050). BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
73
Chapter 10
VIII - AIR/WATER HEAT EXCHANGER (HEATING OF THE INLET AIR)
A - ROLE
The air/water heat exchanger heats the inlet air in the cylinders (during the
particle filter regeneration assistance phase).
The inlet air heater is used to increase the combustion temperature required
to regenerate the particle filter.
B - DESCRIPTION
The air/air heat exchanger, which cools the inlet air in the cylinders, is
surrounded by an air/water exchanger which heats the inlet air. C - LOCATION
74
15
SDI021C
15 - air/water heat exchanger (inlet air heater)
74 - air/air heat exchanger
The water/air heat exchanger (15) is located near to the front air/air heat
exchanger (74).
IX - INLET AIR HEATER THROTTLE
A - DESCRIPTION
Warning: The inlet air heater throttle is closed when it is not controlled
pneumatically.
B - LOCATION
The throttle housing is located at the inlet to the inlet manifold.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
74
Chapter 10
X - THROTTLE HOUSING CONTROL ELECTROVALVE (HEATING OF THE INLET AIR) (1285)
A - ROLE
The electrovalve controls the opening of the inlet air heater throttle. B - DESCRIPTION
The electrovalve is the same as the following electrovalves:
, turbocharging pressure regulation electrovalve,
, exhaust gas recycling electrovalve (EGR),
, throttle housing control electrovalve (EGR).
mp
n
SDI022C
qmn
m - "user" output
n - vacuum pump vacuum inlet
p - white marking ( bia?a plamka )
q - atmospheric pressure inlet
The electrovalve is controlled with an OCR (open cycle ratio).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
75
Chapter 10
The proportional electrovalve controlled with an OCR voltage is connected to the following:
, atmospheric pressure,
, vacuum supplied by the vacuum pump.
The pressure supplied by the electrovalve is between atmospheric pressure and the vacuum from the vacuum pump.
The electrovalve connects the vacuum pump and the heater throttle. Operating phases with particle filter regeneration assistance: , engine at low load and mid load: the inlet air heater throttle is open (controlled),
, engine at full load: the inlet air heater throttle is closed (not controlled) (in moderate ambient temperature).
Note: The inlet air heater throttle can be controlled outside the regeneration
assistance operating phase (engine cold, moderate ambient
temperature).
C - ELECTRICAL FEATURES
Control: injection ECU (earth).
Variable voltage control (OCR):
, full supply (maximum OCR) = maximum vacuum,
, no supply (minimum OCR) = no vacuum (atmospheric pressure).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
76
Chapter 10
D - LOCATION
17
SDI023C
17 - inlet air heater throttle control electrovalve
The electrovalve is located between the air filter housing and the inlet
manifold. It has a 2 way orange connector. BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
77
Chapter 10
XI - THROTTLE HOUSING CONTROL ELECTROVALVE (EGR) (1263)
A - ROLE
The electrovalve controls the closing of the throttle housing (EGR). B - DESCRIPTION
Warning: The throttle housing is open when it is not controlled
pneumatically.
Operating phases with particle filter regeneration assistance:
, engine at low load: the throttle housing is closed (controlled) (**)
(depending on exterior temperature),
, engine at mid load and full load: the throttle housing is open (not
controlled).
(**) the engine only lets in heated air.
The electrovalve has a 2 way black connector.
XII - BUILT-IN SYSTEMS INTERFACE (BSI1)
A - ROLE
The BSI performs the following operations:
, it transmits information from the fuel additive ECU to the injection ECU,
, it transmits information from the injection ECU to the fuel additive ECU,
, it informs the driver of the status of the pollutant particle filtration system,
, it reinitialises the system after a maintenance operation. BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
78
Chapter 10
B - DIAGRAM
79
Key:
A - VAN network
B - CAN network
C - Wire connection
BSI1 - Built-in systems interface
1282 - Fuel additive ECU
1320 - Injection ECU
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
77
80
1320
78
81
82
83
BSI1
89
84
88
85
1282
86
SDI024P
87
A
B
C
79
Chapter 10
CONNECTIONS
CONNECTION SIGNAL SIGNAL N? NATURE 77 Operating status of the additive ECU CAN
Low additive level reached warning CAN
Total quantity of additive injected since start of CAN particle filter's life
Exhaust gas temperature (downstream of the CAN catalytic converter)
Request to force fan unit (at low speed) CAN
Request to force pre-post heater plugs CAN
78 Request to illuminate diagnostic LED VAN
Particle filter fault CAN
Request to activate consumers (alternator CAN saturation)
Request to force fan unit (at mid speed) CAN
Engine speed sensor signal (engine running CAN information)
79 Pre-post heating unit / preheater plugs control All or nothing 80 Fan unit relay control (at low speed) All or nothing 81 Fan unit relay control (at mid speed) All or nothing 82 Heated rear screen relay control All or nothing 83 Request to illuminate diagnostic LED VAN
Request to flash service LED on the control VAN panel (*)
Request to display a message on the VAN multifunction screen (*)
84 Operating status of the additive ECU VAN
Low additive level reached warning VAN
Total quantity of additive injected since start of VAN particle filter's life
Status of the fuel filler cap presence sensor VAN
Exhaust gas temperature (downstream of the VAN catalytic converter)
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
80
Chapter 10
CONNECTIONS
CONNECTION SIGNAL SIGNAL N? NATURE
85 Engine speed sensor signal (engine running VAN
information)
Fuel sender information VAN
Ignition key position VAN
Vehicle speed information VAN
86 Fuel filler cap presence sensor All or nothing
87 Exhaust gas temperature (downstream of the Analogue
catalytic converter)
88 Fuel sender Analogue
89 Ignition key All or nothing (*) depending on equipment.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
81
Chapter 10
XIII - INJECTION ECU (1320)
A - ROLE
The ECU software performs:
, the functions for controlling injection and depollution,
, the control of particle filter regeneration,
, the driving pleasure strategies,
, the emergency strategies,
, the control of the fan units and warning LEDs (*),
, the diagnostic function with memorising of faults,
, the dialogue with the fuel additive ECU,
, the dialogue with the automatic gearbox ECU (*),
, the dialogue with the electronic stability program ECU (*).
(*) depending on equipment.
B - DESCRIPTION
The ECU is responsible for electrically controlling the following components:
, differential pressure sensor,
, exhaust gas temperature sensor (upstream of the catalytic converter),
, inlet air heater throttle control electrovalve.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
82
Chapter 10
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
83
Chapter 11
FUEL ADDITIVE FUNCTION I - ADDITIVE
A - ROLE
Role of the additive:
, to lower the particle combustion temperature to 450:C (instead of 550:C),
, to impregnate the particles forming in the combustion chamber,
, to propagate combustion of the particles.
B - DESCRIPTION
EOLYS additive (supplied by RHODIA).
Composition:
, cerine: 4.2% by weight (DP X42),
, catalytic converter: brown in colour,
, solvent product (combustible hydrocarbon). BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
84
Chapter 11
II - ADDITIVE TANK
A - DESCRIPTION
Specifications:
, capacity: 5 litres,
, range: 80 000 km,
, integrated additive injection pump,
, integrated low additive level sensor,
, 4 orifices.
Orifices:
, additive injection pump outlet (10 mm diameter click-fit connector),
, additive injection pump return (8 mm diameter click-fit connector),
, breather (pressure - vacuum safety valve),
, degassing (overflow).
Filling: refer to the procedure given in the mechanical file of the vehicle in
question.
B - LOCATION
Location: under the fuel tank.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
85
Chapter 11
III - ADDITIVE INJECTION PUMP (1283)
A - ROLE
The additive injection pump supplies the pressure and the flow required in the
additive circuit.
B - DESCRIPTION
2
351
4
A
B
SDI030D
A - Additive return circuit
B - Additive low pressure circuit
Supplier: MARWAL
The additive injection pump comprises the following components:
1 - Non return valve (additive low pressure circuit) 2 - Low additive level sensor
3 - Filter
4 - Non return valve (additive tank return circuit) 5 - Roller displacement pump
The non return valves prevent additive from flowing out when the additive
injection pump outlet and return click-fit connectors are opened.
Note: Safety valve rating: 0.2 bar.
Pump flow: 80 l/h.
Normal operating pressure: 3 bars.
The additive pump is supplied with 12 volts by the fuel additive ECU in the
following cases:
- for 5 seconds when the ignition is switched on - during the additive phase
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
86
Chapter 11
C - ELECTRICAL FEATURES
Controlled by the fuel additive ECU.
Allocation of connector channels:
, channel 1: (-) low additive level sensor,
, channel 2: (+) low additive level sensor,
, channel 3: additive injection pump 12 volt supply,
, channel 4: additive injection pump earth,
, channel 5: spare,
, channel 6: spare.
D - LOCATION
The pump is submerged in the additive tank.
Note: The pump cannot be separated from the additive tank.
III - LOW ADDITIVE LEVEL SENSOR (1283)
A - ROLE
The sensor informs the additive ECU that the low additive level has been
reached when there is 0.3 litres remaining in the additive tank.
Depending on the information received, the additive ECU informs the fuel
injection ECU.
The injection ECU informs the BSI which requests activation of the following:
, request to flash the service LED on the control panel (*),
, request to display a message on the multifunction screen (*).
Note: 0.3 litres of additive is sufficient to fill up the tank 6 times with 80 litres
of fuel (*).
(*) depending on vehicle equipment.
B - DESCRIPTION
The sensor consists of a thermistor.
The information provided varies, depending on whether the thermistor is in
the additive or in air (minimum level reached).
C - LOCATION
The sensor is incorporated into the additive injection pump.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
87
Chapter 11
IV - SAFETY VALVE
A - ROLE
Role of the safety valve:
, sealing function (prevents the solvent from evaporating and the ingress of
dust, mud and water),
, overturn safety function,
, breather for the additive tank depending on the additive level. B - DESCRIPTION
9
8
9
78
SDI031D76
6
6 - Vacuum valve (0.036 bar)
7 - Pressure relief valve (0.05 +/- 0.01 bar)
8 - Vacuum valve return spring
9 - Pressure relief valve return spring
Operation:
, the valve (6) acts as a breather for the additive tank depending on the
additive level,
, the valve (8) performs the sealing and overturn safety function.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
88
Chapter 11
C - LOCATION
SDI032C
The safety valve is located in the rear left hand wheel arch (behind the mud
flap).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
89
Chapter 11
V - ADDITIVE INJECTOR (1284)
A - ROLE
The injector is used to inject a set amount of additive into the fuel tank.
B - DESCRIPTION
A - Additive return circuit SDI033D
B - Additive low pressure circuit
Type: WEBER IWP 043
Note: Safety valve rating: 3 bars. C - ELECTRICAL FEATURES
Controlled by the fuel additive ECU.
Allocation of connector channels:
, channel 1: +12 volts supply,
, channel 2: control.
Electrical specifications: resistance at 25 :C = 14.7 ohms. C - LOCATION
The additive injector is located on the fuel tank.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
90
Chapter 11
VI - FUEL FILLER CAP PRESENCE SENSOR (4320)
A - ROLE
The fuel filler cap presence sensor informs the additive ECU whether the fuel
filler cap is open or closed.
Role of the additive ECU depending on the information received: to detect
whether fuel may have been added.
B - DESCRIPTION
11
10
SDI034C
10 - Permanent magnet
11 - Contact
The filler cap is fitted with a magnet. When the cap is closed, the magnet is
opposite the contact.
C - ELECTRICAL FEATURES
Supply: fuel additive ECU.
Allocation of connector channels:
channel 1: 5 volt supply, ,
, channel 2: signal,
, presence of the magnet opposite the contact: resistance = 150 000 ohms,
, absence of the magnet opposite the contact: resistance = 15 ohms.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
91
Chapter 11
VII - FUEL SENDER (1211)
A - ROLE
The fuel sender informs the additive ECU of a variation in fuel level, through
the built-in systems interface.
Role of the additive ECU depending on the information received:
, to determine the amount of additive to be injected,
, to control the additive injection pump,
, to control the additive injector. B - DESCRIPTION
H
SDI035C
Controlled by the fuel sender.
Supplier VDO:
HEIGHT OF THE FLOAT AXIS IN RESISTANCE
RELATION TO THE BASE LEVEL
14 mm 350 , 5 ohms
44 mm 300 , 5 ohms
75 mm 250 , 5 ohms
110 mm 200 , 5 ohms
139 mm 150 , 5 ohms
171 mm 100 , 5 ohms
202 mm 50 , 5 ohms
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
92
Chapter 11
Supplier MARWAL:
HEIGHT OF THE FLOAT AXIS IN RESISTANCE
RELATION TO THE BASE LEVEL
14 mm 350 , 11 ohms
41 mm 300 , 10 ohms
72 mm 250 , 10 ohms
104 mm 200 , 9 ohms
138 mm 150 , 9 ohms
171 mm 100 , 8 ohms
204 mm 50 , 2 ohms Note: The fuel sender cannot detect a variation in fuel level of less than 7
litres precisely.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
93
Chapter 11
VIII - BUILT-IN SYSTEMS INTERFACE (BSI1)
The BSI sends the additive ECU the following information:
, engine speed sensor signal (engine running information),
, vehicle speed information,
, fuel sender information,
, ignition key position.
IX - FUEL ADDITIVE ECU (1282)
A - ROLE
The ECU controls additive injection.
The ECU software is responsible for:
, controlling the start of additive injection and additive injection time into the
fuel tank,
, managing the total amount of additive injected since the beginning of the
filter's life,
, the emergency strategies,
, diagnostic with memorising of faults,
, dialogue with the injection ECU.
B - DESCRIPTION
The ECU electrically controls the following components:
, low additive level sensor,
, additive injection pump,
, additive injector,
, fuel filler cap presence contact,
, catalytic converter downstream exhaust gas temperature sensor.
Supplier: MAGNETTI MARELLI.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
94
Chapter 11
C - ELECTRICAL FEATURES
Allocation of connector channels:
CHANNEL N? DESCRIPTION
1 + 12 volt supply (permanent +BAT)
2 +BAT BSI / + ignition on supply
3 +BODY VAN supply (+12 volts)
4 Input: fuel filler cap presence sensor information
5 Input: low additive level sensor information
6 -
7 -
8 Output: additive injector 12V control
9 Output: additive injection pump 12V control
10 Input: catalytic converter downstream exhaust gas
temperature sensor information
11 Input: catalytic converter downstream exhaust gas
temperature sensor information
12 Input: fuel filler cap presence sensor information
13 Input: low additive level sensor information
14 VAN Data network
15 VAN Data bar network
16 Earth
D - LOCATION
Location: on the chassis member near to the bottom of the RH centre post
(depending on vehicle).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
95
Chapter 12
OPERATING PHASES:
HDI DIRECT INJECTION SYSTEM
I - COMPONENTS COMMON WITH DOCUMENT "BOSCH EDC 15C2 HDI
INJECTION SYSTEM"
Components common with the document: , foreword,
, injection diagram,
, role of the main cartographic maps, , general operation,
, working out the amount of fuel to inject, , high pressure fuel regulation, , direct injection,
, working out the injection type, , turbocharging pressure regulation, , starting the engine,
, stopping the engine,
, engine operating safety,
, driver's information function.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
96
Chapter 12
II - SPECIFIC COMPONENTS
Specific features of the DW12TED4 engine:
, turbocharging pressure regulation,
, exhaust gas recycling regulation,
, pre-post heating,
, additional heating,
, air conditioning compressor cut-off,
, displaying faults,
, downgraded operating modes.
III - TURBOCHARGING PRESSURE REGULATION - FEATURE
The turbocharging pressure is reduced to prevent the turbocharger from being
damaged in the following cases:
, when the altitude is above 500 m,
, when the exterior air temperature is above 28:C (at the inlet manifold inlet).
During part of the EGR phase (low engine speed / low load), the turbocharging
pressure is controlled in an open loop to prevent any interference on the air loop.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
97
Chapter 12
IV - EXHAUST GAS RECYCLING REGULATION
2
134
7
5
6SDI036C
1 - Air flowmeter
2 - Engine speed sensor
3 - Injection ECU
4 - Exhaust gas recycling valve (EGR)
5 - Throttle housing (EGR)
6 - Throttle housing control electrovalve (EGR)
7 - Recycling regulation electrovalve (EGR)
Exhaust gas recycling is of progressive type and is controlled by a cartographic map.
Role of the injection ECU depending on the information received (exhaust gas recycling rate determined in the cartographic map):
, to control the exhaust gas recycling electrovalve with an OCR voltage, , to determine the exhaust gas recycling rate,
, to correct the OCR applied to the exhaust gas recycling electrovalve so as to obtain the theoretical recycling rate equal to the measured rate. Note: Exhaust gas recycling rate = difference between the measurement from the
air flowmeter and the calculation of the amount of air entering the engine
(depending on engine speed and air temperature).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
98
Chapter 12
Conditions allowing exhaust gas recycling: , engine speed greater than 725 rpm,
, low engine load,
, coolant temperature (ECU cartographic map) / air temperature (ECU
cartographic map),
, regeneration assistance not active. Conditions prohibiting exhaust gas recycling: , full engine load,
, engine speed greater than 2650 rpm, , altitude above 1500 m,
, coolant temperature above 105:C,
, regeneration assistance active.
Throttle housing (EGR):
, in addition to the recycling valve, the throttle housing, depending on its position,
is used to improve exhaust gas recycling, , the throttle housing is controlled progressively and using a cartographic map
(injection ECU).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
99
Chapter 12
V - PRE-POST HEATING
The preheating and postheating times are determined by the ECU depending on
the coolant temperature.
VI - PREHEATING OPERATION
The preheating time varies as a function of coolant temperature.
COOLANT TEMPERATURE PREHEATING TIME
15 seconds - 25:C
10 seconds - 18:C
0.5 seconds - 10:C
0.5 seconds - 1:C
VII - HEATING OF THE PLUGS WHILST CRANKING
During the cranking phase, the plugs are energised in the following cases:
, coolant temperature below 25:C?
, engine speed less than 70 rpm for 0.2 seconds.
Note: After the LED extinguishes, if the starter motor is not operated, the
preheater plugs remain energised for a maximum of 10 seconds. VIII - POSTHEATING OPERATION
Postheating can extend the operation of the plugs after the cranking phase.
COOLANT TEMPERATURE POSTHEATING TIME
180 seconds - 25:C
180 seconds 17:C
400 seconds 19:C
400 seconds 25:C
0 seconds 50:C
Parameters which can interrupt postheating:
, coolant temperature above 50:C,
, engine speed above 1500 rpm.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
100
Chapter 12
IX - ADDITIONAL HEATING
As the engine is highly efficient, a system is required to assist the rise in
temperature in the passenger compartment in cold climates. The passenger compartment temperature rise assistance system is controlled by
the built-in systems interface and operated by the injection ECU. 2 devices are used depending on the marketing country: , several thermoplungers (electrical resistors) located in the coolant circuit of the
heater matrix,
, an additional fuel powered heater located in the front left hand wheel arch (for
vehicles in very cold countries).
A - DIAGRAM
8098
64151220
9050
1320
BSI1
A
B1190CSDI037D
Key:
A - VAN network
B - CAN network
C - Wire connection
(1220) Coolant temperature sensor.
(1320) Injection ECU.
(6415) Exterior air temperature sensor.
(8098) Electrical resistors.
(1190) Additional heater.
(9050) Front RH door station.
(BSI1) Built-in systems interface.
The built-in systems interface authorises operation of these additional heating
systems depending on the following parameters:
, coolant temperature,
, exterior air temperature.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
101
Chapter 12
B - PRESENTATION OF THE ADDITIONAL HEATING SYSTEMS
1 - Electrical resistors
+ig. on +BAT
BSI1
8098 8098 8098 1320
SDI038C
Assembly with 3 relays and 3 resistors
1320 - Injection ECU
8098 - Electrical resistors
BSI1 - Built-in systems interface
The resistors can each supply a power of 330 watts.
This assembly allows heating powers of 330, 660 or 990 watts.
2 - Additional heater
The wiring only allows one heating power to be obtained.
The additional heater is controlled by an integrated ECU. C - CONTROL OF THE PASSENGER COMPARTMENT HEATING SYSTEMS
The additional heater is switched on in the following cases:
low passenger compartment temperature (specific curve), ,
, when the engine operating conditions so allow.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
102
Chapter 12
D - WORKING OUT THE ADDITIONAL HEATING REQUIREMENTS
Te
80a70
65
b40
SDI039D
Ta-20-1010
ta - Exterior air temperature
te - Coolant temperature
a - Example 1
b - Example 2
(outside shaded area) heating authorisation zone.
The BSI determines the passenger compartment heating requirement when
the engine is started depending on the exterior air temperature and the
coolant temperature.
Example 1:
, coolant temperature = 40:C,
, exterior temperature = 10:C,
, the temperature conditions are within the additional heating operating zone.
Example 2:
, coolant temperature = 70:C,
, exterior temperature= 10:C.
, the temperature conditions are outside the additional heating operating
zone.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
103
Chapter 12
E - OPERATION
The BSI determines the passenger compartment heating requirement when the engine is started depending on the exterior air temperature and the coolant temperature.
The built-in systems interface operates the additional heater in the following conditions:
, engine operating for more than 60 seconds,
, engine speed above 700 rpm,
, battery voltage greater than 12 volts (positive electrical balance), , coolant temperature above 40:C.
The built-in systems interface controls the heater stages progressively: , first stage,
, second stage,
, second stage and first stage.
The additional heating is switched off when the temperature conditions so allow (curve).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
104
Chapter 12
X - AIR CONDITIONING COMPRESSOR CUT-OFF
The injection ECU is connected to the following components:
, a pressurestat located on the air conditioning circuit,
, the coolant temperature sensor.
The ECU can cut off the supply to the electromagnetic clutch of the air conditioning compressor in the following cases:
, engine speed less than 700 rpm,
, coolant temperature greater than 115:C,
, pressure in the air conditioning circuit less than 2.5 bars (re-authorisation at 3 bars),
, pressure in the air conditioning circuit greater than 30 bars (re-authorisation at 28 bars).
XI - ENGINE IMMOBILISER FUNCTION
The injection ECU prevents the engine from being started by prohibiting injection. Device operating principle: refer to the corresponding documentation. Unlocking the system
When the ignition is switched on, the authenticity of the keys is checked by the BSI.
Locking, ignition off
The injection ECU is automatically locked 20 seconds maximum after the ignition is switched off.
Parts replacement procedure
Refer to the repair section.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
105
Chapter 12
XII - DISPLAYING FAULTS: DOWNGRADED MODES OPERATION A - DISPLAYING FAULTS
The appearance of certain faults in the injection system leads to the
illumination of the engine diagnostic LED. The engine diagnostic LED illuminates if a fault occurs on the following
components or information:
, capacitor N:1 voltage,
, capacitor N:2 voltage,
high pressure fuel sensor, ,
, high pressure fuel monitoring,
, fuel pressure regulator/sensor coherence, , accelerator pedal sensor N:1,
, accelerator pedal sensor N:2,
, inlet manifold pressure sensor,
, air flowmeter,
, stability of the ECU 5 volt supply,
, exhaust gas recycling function (regulation), , high pressure fuel regulator,
, diesel injector fault (1 - 4),
, inlet pressure,
, "Swirl" control electrovalve,
, telecoding,
, turbocharging function.
B - DOWNGRADED OPERATING MODES
The injection system manages the following downgraded modes:
, an operating mode with a reduced fuel flow, , the other mode leads to the engine being stopped immediately.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
106
Chapter 12
C - REDUCED FUEL FLOW
This downgraded operating mode limits the fuel flow and the engine speed 3cannot exceed 2200 rpm (with the injected fuel flow being less than 30 mm).
The injection system switches to "reduced flow" mode when a fault is present
on one of the following components:
, high pressure fuel sensor,
, fuel pressure regulator/sensor coherence,
, accelerator pedal sensor N:1,
, accelerator pedal sensor N:2,
, inlet manifold pressure sensor,
, air flowmeter,
, exhaust gas recycling function (regulation),
, high pressure fuel regulator,
, stability of the ECU 5 volt supply,
, diesel injector fault (1 - 4),
, inlet pressure,
, turbocharging function.
D - AIR CONDITIONING COMPRESSOR CUT-OFF
The injection ECU cuts off the supply to the air conditioning compressor clutch
if a fault is detected on the fan unit control relay coils.
E - HIGH PRESSURE FUEL PUMP 3RD PISTON DEACTIVATOR
When the fuel temperature is above 106:C, the injection ECU deactivates the rd3 piston of the high pressure pump (solenoid energised). F - STOPPING THE ENGINE
The system stops the engine immediately when a fault is present on one of
the following components:
, Eprom in the injection ECU
, engine speed sensor
, capacitor N:1 voltage
, capacitor N:2 voltage
, high pressure fuel monitoring
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
107
Chapter 12
XIII - COOLANT TEMPERATURE WARNING LED (V4020) - FEATURE
The coolant temperature warning LED can be controlled by one of the following
components:
, injection ECU,
, coolant temperature sensor (2 channels).
Normal LED operation:
, the LED illuminates if the temperature exceeds 118:C,
, the LED extinguishes if the temperature falls below 117:C.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
108
Chapter 12
XIV - CRUISE CONTROL
The cruise control device is used to maintain the vehicle speed at a value programmed by the driver in the following cases:
, when the accelerator pedal is not pressed,
, regardless of the road profile,
without pressing the brake pedal. ,
Possibilities offered by the cruise control device:
, the driver can exceed the programmed speed by pressing the accelerator pedal, , the driver can cancel cruise control by pressing the brake pedal, the cruise control switch or the on/off button.
Note: The cruise control device can only be used above 40 km/h. Operation.
When cruise control is on, the injection ECU permanently compares the programmed speed with the vehicle's instantaneous speed.
The speed information is supplied by the speed sensor.
When the programmed speed is greater than the vehicle's current speed, the injection ECU increases the fuel flow: the vehicle accelerates up to the programmed speed.
When the vehicle's current speed is greater than the programmed speed, the injection ECU reduces the fuel flow: the vehicle decelerates down to the programmed speed.
Cruise control is cancelled by pressing:
, the accelerator pedal,
, the clutch pedal,
, the on/off button,
, the brake pedal.
Note: In the above 4 cases, the vehicle decelerates very quickly (accelerator
released without declutching).
When cruise control is cancelled by pressing the cruise control button, the vehicle decelerates slowly.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
109
Chapter 13
OPERATING PHASES:
PARTICLE FILTRATION
I - GENERAL PRINCIPLE
The aim of filtration is to remove the particles retained on the filter walls. Regeneration consists of periodically burning off the particles accumulated in the particle filter.
Regeneration can be natural if the temperature of the exhaust gases is sufficient. Regeneration can be caused by the injection ECU if the temperature of the exhaust gases is insufficient and if the particle filter is clogged. The injection ECU artificially increases the temperature of the exhaust gases using post-injection: this is the "regeneration assistance" phase. Note: The driving conditions directly affect the temperature of the exhaust gases
and consequently the temperature inside the particle filter. The injection ECU permanently controls the following components: , the status of the filter using a function which monitors the load level of the particle filter,
, regeneration assistance using a regeneration assistance function.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
110
Chapter 13
II - DIAGRAM
1 2
3
4
5 20
6
7
8
19
9
10
18
17
11
12 16
13
14 15
A - VAN network
SDI040P B - CAN network
C - Wire connection
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
111
Chapter 13
REF. DESCRIPTION 1 Built-in systems interface
2 Mileage
3 Central diagnostic socket
4 Diagnostic LED
5 Service LED
6 Heated rear screen
7 Fan unit(s)
8 Pre-post heating unit
9 Diesel injectors
10 High pressure fuel pump 3rd piston deactivator 11 Recycling regulation electrovalve (EGR) 12 Throttle housing control electrovalve (EGR) 13 Throttle housing control electrovalve (inlet air heater) 14 Turbocharging pressure regulation electrovalve 15 Air flowmeter
16 Differential pressure sensor
17 Exhaust gas temperature sensor (upstream of the catalytic
converter)
18 Injection ECU
19 Exhaust gas temperature sensor (downstream of the catalytic
converter)
20 Fuel additive ECU
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
112
Chapter 13
III - PARTICLE FILTER LOAD LEVEL MONITORING FUNCTION
A - ROLE
- To determine the condition of the particle filter (clogging level) - To request activation of the regeneration assistance function, when necessary
- To ensure the effectiveness of the regeneration assistance function. Main information used for monitoring the particle filter: , pressure differential,
, exhaust gas temperature (downstream of the catalytic converter), , exhaust gas temperature (upstream of the catalytic converter), , number of miles travelled,
, inlet air flow.
Note: This information depends on the load level of the particle filter. B - WORKING OUT THE PARTICLE FILTER LOAD LEVEL
The amount of particles present in the filter varies its load loss (inlet / outlet pressure differential).
This permanently measured value represents the load level of the particle filter.
The cartographic maps of the injection ECU have 6 operating levels determined by curves, from the volume flow of exhaust gases. The volume flow of exhaust gases is essentially calculated from the following parameters:
, pressure differential,
, inlet air flow,
, atmospheric pressure,
, exhaust gas temperature (downstream of the catalytic converter).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
113
Chapter 13
C - PARTICLE FILTER LOAD LEVELS
E
900
f
e
d
c
b
a
DSDI041D
D - Exhaust gas volume flow (l/h)
E - Pressure differential (mbar)
a - Filter punctured
b - Filter regenerated
c - Intermediate zone
d - Filter loaded
e - Filter overloaded
f - Filter clogged
Note: These statuses can be read using the diagnostic tool, in parameter
measurements.
Zones "a" - "f" represent the possible clogging levels of the particle filter. The aim of the injection ECU is to be permanently in zone "b" or "c" (regardless of vehicle mileage).
When leaving zone "c" to go to zone "d" (at a variable speed depending on driving conditions), the injection ECU requests regeneration assistance to return to zone "b" or possibly "c" (depending on driving conditions). Note: Zones "a" and "f" are zones where the pressure differential is
abnormal.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
114
Chapter 13
The injection ECU requests activation of the regeneration function in the following cases:
, load level of the filter passing from zone "c" - "d",
, load level of the filter in zone "e" or "f",
, load level of the filter in zone "c" and driving conditions favourable for regeneration (average speed greater than 70 km/h) (**),
(**) under these conditions regeneration will be quicker (regeneration strategy in economic conditions).
Filter overloaded - zone "e"
The injection ECU switches to the overloaded filter state when regeneration has failed under certain driving conditions.
This is a warning state.
Filter clogged - zone "f"
The pressure differential is permanently greater than 900 mbar (maximum back pressure allowable by the engine) or greater than a limit depending on the volume flow rate.
Possible causes of the fault:
regeneration assistance ineffective, ,
, filter clogged with cerine,
, incorrect information from the differential pressure sensor. The injection ECU suspends all requests for regeneration assistance and signals a fault.
IMPORTANT: If the "filter clogged" fault occurs, it is essential to locate the
origin of the clogging or else the filter will be damaged. Filter punctured - zone "a"
The pressure differential is less than a limit, depending on the volume flow rate.
Possible causes of the fault:
, incorrect information from the differential pressure sensor , sealing fault of the exhaust pipe, upstream/downstream information pipes , filter actually punctured
The injection ECU suspends all requests for regeneration assistance and signals a fault.
Note: The "filter punctured" fault may be due to an excess temperature
during a regeneration as the amount of burnt particles may be too
great.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
115
Chapter 13
D - CORRECTION OF THE LOAD LEVELS DEPENDING ON THE AMOUNT OF
CERINE
The cerine in the fuel:
, is not burnt with the soot,
, builds up on the walls of the particle filter.
The injection ECU therefore permanently adapts its cartographic maps
depending on the amount of cerine accumulated in the particle filter.
E - EFFECT OF DRIVING CONDITIONS ON THE PRESSURE DIFFERENTIAL
The change in pressure differential also depends on the following parameters:
, fuel consumption (fuel + additive),
, vehicle driving conditions (activation of post-injection),
, exhaust gas temperature,
, exhaust gas speed in the particle filter.
GD - Volume flow of exhaust gases (l/h)
E - Pressure differential (mbar)
F - Road or motorway type driving (before regeneration)
FG - Urban type driving (before regeneration)
h - Filtered exhaust gases
g - Deposits (cerine, soot, unburned hydrocarbons, oil deposits, etc)
Example F:
, the deposits collect at the bottom of the particle filter,
, the gases pass easily through the channels and the pressure differential is
low.
Example G: g
, the deposits collect in a stratified layer on the channels,
, the gases have problems passing through the channels and the pressure
differential is high.
Warning: For the same amount of cerine and for the same vehicle mileage,
the differential pressure may vary.
g
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
h
h
EE
DD
SDI042D
116
Chapter 13
IV - REGENERATION ASSISTANCE MANAGEMENT FUNCTION
A - ROLE
, To control requests from the monitoring function.
, To activate the functions required for regeneration, depending on the
monitoring states.
, To determine the required regeneration assistance level.
, To control the effects of post-injection on engine operation. Regeneration consists of periodically burning off the particles accumulated on the filter enabling it to remain in zone "b" or "c".
Filter regeneration depends on the temperature of the exhaust gases which must be above the soot combustion limit.
There are 2 techniques for achieving this:
, natural regeneration,
, artificial regeneration (regeneration assistance).
Natural regeneration.
When the exhaust temperature reaches the regeneration limit itself (high engine load), the particles burn off naturally in the particle filter. No external actions are required to assist regeneration.
Artificial regeneration (regeneration assistance).
Regeneration assistance is a set of provisions controlled by the injection ECU, the aim of which is to increase the temperature of the exhaust gases to the regeneration limit.
B - WORKING OUT THE REQUIRED REGENERATION ASSISTANCE LEVEL
There are 2 types of regeneration assistance, depending on the thermal state of the exhaust pipe:
, level 1 regeneration assistance (cartographic maps for cold exhaust pipe
and catalytic converter) (catalytic converter pre-heating), , level 2 regeneration assistance (cartographic maps for warm exhaust pipe).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
117
Chapter 13
C - LEVEL 1 REGENERATION ASSISTANCE
When the monitoring function detects a change in operating zone, it requests activation of level 1 regeneration assistance (e.g. changing from zone "c" to "d").
Every time activation is requested, the injection ECU performs the following operations:
, it prevents exhaust gas recycling (EGR),
, it requests activation of electrical consumers (heated rear screen, fan unit, preheater plugs) (*),
, it controls the opening and closing of the inlet air heater throttle (if necessary),
, it activates post-injection (heating of the exhaust gases).
(*) this request is subject to the electrical load shedding strategy of the BSI (depending on equipment).
D - LEVEL 2 REGENERATION ASSISTANCE
The principle is the same as level 1 regeneration assistance but stricter cartographic maps lead to a higher exhaust gas temperature.
The switch from level 1 to level 2 regeneration assistance depends on the following conditions:
, upstream and downstream exhaust temperature,
, for as long as the temperature has not reached a limit.
It is impossible to switch from level 1 to level 2 regeneration assistance if level 1 has not been active for a given time.
E - CASE OF REQUESTING REGENERATION ASSISTANCE IN ECONOMIC
CONDITIONS (BY THE MONITORING FUNCTION)
The aim of this request is to activate regeneration assistance under optimum driving conditions, in order to reduce fuel consumption.
The principle is the same as levels 1 and 2 regeneration assistance but with a shorter post-injection time.
Parameters required:
, particle filter in zone "c", "e" or "f",
, sufficient vehicle speed or engine speed/load for a given time
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
118
Chapter 13
F - CONDITIONS FOR ACTIVATING REGENERATION ASSISTANCE (BY THE MONITORING FUNCTION)
Parameters which can activate regeneration assistance: , pressure differential,
, distance travelled between each regeneration.
PARAMETERS REGENERATION ASSISTANCE
Pressure differential Activation Pressure differential
(above a limit "E")
Deactivation Effective post-injection time (above a limit "K")
Distance Activation Distance travelled since last
regeneration (above a limit "J")
Deactivation Effective post-injection time (above a limit "K")
G - PRESSURE DIFFERENTIAL
The pressure differential parameter is used to activate regeneration assistance independently to the distance information. When this condition is responsible for determining activation of regeneration assistance, an effective post-injection time must have elapsed before regeneration assistance can be stopped (this allows complete soot combustion, in normal operation).
Monitoring the post-injection time:
, prevents the post-injection time being too long (damage to the engine, expansion of the engine oil),
, limits fuel consumption.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
119
Chapter 13
H - DISTANCE
The distance parameter:
, activates regeneration assistance independently to the pressure differential information,
, limits the amount of soot to be burnt off in the filter, should the pressure differential information fail.
Note: Too many particles to be burned would lead to excessive
temperatures which would damage the particle filter.
If the average distance of the last 5 regenerations is less than a limit (350 km), the injection ECU switches to the "distance" strategy.
The distance travelled since the last regeneration is counted by the main injection ECU which activates regeneration assistance when this counter reaches a limit "J".
This limit, or regeneration frequency, depending on the total distance travelled by the particle filter.
The regeneration frequency must be increased to take into account the reduction in capacity of the particle filter (consumption/quantity of accumulated cerine).
J
1400
850
0HSDI043C80 000
H - Distance travelled by the particle filter (km)
J - Regeneration frequency (km)
I - OTHER CONDITIONS
Other conditions authorising activation of regeneration assistance: , coolant temperature above 60:C,
, sufficient engine speed / load.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
120
Chapter 13
V - EFFECTS OF ACTIVATING REGENERATION ASSISTANCE
A - PROHIBITION OF EXHAUST GAS RECYCLING REGULATION (EGR)
Every time regeneration assistance is activated, the injection ECU prohibits exhaust gas recycling regulation:
, exhaust gas recycling valve closed (prevents any hunting phenomena), , throttle housing open (except if closing is requested to force air to flow into
the heater).
B - ACTIVATION OF ELECTRICAL CONSUMERS
1 - Role
Reason for activating electrical consumers:
, to increase the resistant torque of the alternator, thus leading to an
increase in engine load,
, to facilitate the rise in temperature of the exhaust gases,
, to quickly place the engine operating point within conditions allowing
effective post-injection.
2 - Operation
The injection ECU asks the BSI to activate consumers which absorb a
high power (alternator saturation request) (*).
(*) depending on vehicle equipment.
Order in which consumers are activated by the BSI (**):
, heated rear screen control,
, request to force the fan unit at low speed,
control of the fan unit at mid speed, ,
, request to force the pre-post heating plugs.
(**) allowed by the load shedding level of the vehicle (provided that the
battery voltage is above 12.8 volts).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
121
Chapter 13
C - INLET AIR HEATER
The inlet air heater is used:
, to facilitate the rise in temperature of the exhaust gases, , to quickly place the engine operating point within conditions allowing
effective post-injection.
Note: The temperature of the air entering the engine must be between 40:C
and 70:C to allow efficient post-combustion.
D - POST-INJECTION
The catalytic converter, located upstream of the particle filter, is an oxidation catalytic converter.
In the presence of unburned hydrocarbons (HC), the heat efficiency of the catalytic converter increases.
The temperature of the exhaust gases increases.
During post-injection:
, the fuel is injected after Top Dead Centre (20 - 120: crankshaft),
, the temperature of the exhaust pipe increases progressively up to the
regeneration limit.
Once the regeneration limit has been reached, post-injection is maintained until all of the pollutant particles have been eliminated. The post-injection flow and time are determined by cartographic maps, taking into account the engine operating conditions.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
122
Chapter 13
Operating curve:
E
L
L1
L2
E1
K SDI044P
M
E - Pressure differential (mbar)
E1 - Pressure differential curve (mbar)
K - Time (s)
L - Temperature (:C)
L1 - Exhaust gas temperature (downstream of the catalytic converter) (:C)
L2 - Exhaust gas temperature (upstream of the catalytic converter) (:C)
M - Post-injection control
Operation with post-injection: the temperature upstream of the catalytic
converter is less than the temperature downstream of the catalytic converter.
Operation without post-injection: the temperature upstream of the catalytic
converter is greater than the temperature downstream of the catalytic
converter (at steady speed).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
123
Chapter 13
E - EFFECTS ON ENGINE OPERATION
At constant engine load and speed, post-injection leads to an increase in
engine torque.
To maintain the same driving pleasure and avoid engine hesitation during
post-injection, the injection ECU program incorporates the following strategies:
, reduction of the main injection flow,
, turbocharging pressure regulation.
1 - Reduction of the main injection flow
N
n
jkl
SDI045DK
m
K - Time (s)
N - Cylinder pressure (bar)
j - Pre-injection
k - Main injection
l - Post-injection
m - Reduction in main injection time
n - Reduction in cylinder pressure
Reducing the main injection flow cancels out the increase in torque due to
post-injection.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
124
Chapter 13
2 - Turbocharging pressure regulation
To maintain the same engine torque during regeneration assistance, the
turbocharging pressure is regulated.
rd3 - Operation of the high pressure fuel pump 3 piston deactivator
The high pressure fuel pump operates on 3 pistons during regeneration
assistance.
Aim of the system: to provide the flow required by post-injection. BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
125
Chapter 13
VI - FUEL ADDITIVE FUNCTION
A - OPERATION
To lower the regeneration limit, a cerine based additive (Eolys) is added to
the fuel, which lowers the particle combustion temperature from 550:C to
450:C.
Cerine is used in an organic solution stored in an additional tank, located near
to the fuel tank.
An additive system has been developed in order to inject an amount of
additive proportional to the amount of fuel injected.
The system comprises the following components:
, a suction device with a minimum level detector on the additive tank,
, a system for injecting the additive into the fuel tank,
, a specific ECU for controlling the additive function.
Sender filtering requires a pumping limit equal to 7 litres of fuel. BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
126
Chapter 13
Operation:
FUEL ADDITIVE FUNCTION: FUEL ADDITIVE FUNCTION:
ENGINE STATIONARY ENGINE RUNNING
Engine off Non zero vehicle speed
Memorising of the fuel level "n1" Zero vehicle speed
Opening of the fuel filler cap Opening of the fuel filler cap
Memorising of the fuel filler cap open Memorising of the fuel level "n1"
Closing of the fuel filler cap Closing of the fuel filler cap or non zero
vehicle speed
Starting of the engine Acquisition of the fuel level "n2" -
checking of the position of the fuel filler
cap
Acquisition of the fuel level "n2" -
checking of the position of the fuel filler
cap
Case 1: n2 > n1 and fuel filler cap cycle (*) -> fuel additive function - normal
operation
Case 2: n2 > n1 and fuel filler cap cycle faulty or no cycle -> fuel additive function -
fuel filler cap faulty
Case 3: n2 = n1 and fuel filler cap cycle -> fuel additive equal to pumping limit (7 litres)
Case 4: n2 = n1 and fuel filler cap cycle faulty or no cycle -> nothing - normal
operation
(*) fuel filler cap cycle:
, opening of the fuel filler cap,
, closing of the fuel filler cap.
The fuel filler cap cycle is effective if the time interval between opening and
closing is greater than 5 seconds.
B - TOTAL AMOUNT OF ADDITIVE INJECTED
Every time additive is added, the additive ECU memorises the amount of
additive injected.
This value is added to the previously injected values to give a value
representing the total amount of additive injected since the beginning of the
particle filter's life.
This value is sent to the injection ECU which uses it as the basis for
controlling the clogging level of the particle filter with cerine.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
127
Chapter 13
VII - DISPLAYING FAULTS - DOWNGRADED OPERATING MODES
A - DISPLAYING FAULTS
The appearance of certain faults in the particle filtration system leads to the
illumination of the engine diagnostic LED.
The engine diagnostic LED illuminates when a fault is present on one of the
following components or items of information:
, differential pressure sensor,
, exhaust gas temperature sensors (upstream and downstream of the
catalytic converter),
, particle filter clogged,
, particle filter punctured.
B - DOWNGRADED OPERATING MODE
The injection system controls the following downgraded mode: an operating
mode with reduced fuel flow.
C - REDUCED FUEL FLOW
This downgraded operating mode limits the fuel flow such that the engine
speed cannot exceed 2200 rpm under any circumstances (and the injected 3fuel flow remains less than 30 mm).
The injection switches to "reduced flow" mode when one of the following
components is faulty:
, particle filter clogged,
, particle filter punctured,
, exhaust gas temperature sensors (upstream and downstream of the
catalytic converter) (*),
, differential pressure sensor (*).
(*) 200 km after the fault appears.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
128
Chapter 13
D - FUEL ADDITIVE FUNCTION - OPERATION IN DOWNGRADED MODES
3 main strategies are used if the additive system develops a fault.
Fuel filler cap fault:
The additive ECU uses the vehicle speed information in conjunction with the
fuel sender information to inject the additive.
Fuel sender fault:
The additive ECU adds an amount of additive equal to that added for a full
tank when the fuel filler cap is opened/closed.
Communications fault on the VAN multiplexed network:
The additive ECU adds an amount of additive equal to that added for a full
tank when communications are interrupted for more than 10 seconds.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
129
Chapter 13
VIII - DRIVER'S INFORMATION FUNCTION
A - DIAGNOSTIC LED (V1300)
Normal LED operation:
, the LED illuminates when the ignition is switched on.
, after the ignition is switched on, the LED extinguishes after a 4 second
timer.
Abnormal LED operation:
, the LED illuminates when the ignition is switched on,
, the LED remains illuminated.
B - RISK OF THE PARTICLE FILTER CLOGGING
In the event of prolonged idling, regeneration assistance is ineffective (exhaust gas temperature not sufficient).
The filter clogs up with particles.
The injection ECU informs the BSI.
The BSI requests that a message is displayed on the multifunction screen (risk of particle filter clogging) in the following cases: particle filter fault (particle filter overloaded).
The aim is to encourage the driver to adapt his driving to facilitate particle filter regeneration.
Within 100 kilometres after the message appears, the customer must drive for at least 3 minutes at a speed greater than 50 km/h which should cause the message to disappear.
Failure to comply with this recommendation will lead to the following fault: particle filter clogged.
The injection ECU informs the BSI which:
, requests that the diagnostic LED is illuminated,
, requests that a message is displayed on the multifunction screen
(antipollution problem).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
130
Chapter 13
C - MINIMUM LEVEL OF ADDITIVE REACHED
The injection ECU informs the BSI which:
, requests that the service LED is flashed on the control panel (for 20
seconds after the ignition is switched on) (*),
, requests that a message is displayed on the multifunction screen (low
diesel additive level) (after the ignition is switched on) (*).
(*) depending on vehicle equipment.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
131
Chapter 14
MAINTENANCE:
HDI INJECTION SYSTEM
I - RECOMMENDED FUEL
The injection system requires the use of diesel with a low sulphur content (less
than 350 ppm, EURO3 standard).
Warning: It is forbidden to add products such as fuel circuit cleaner and
regalvanising products.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
132
Chapter 14
II - SAFETY INSTRUCTIONS
A - FOREWORD
All operations carried out on the injection system must be performed in accordance with the following provisions and regulations:
, professional healthcare authorities,
, prevention of accidents,
, protection of the environment.
Warning: Operations must be performed by specialist technicians who have
been trained in the safety instructions and precautions to be taken. B - SAFETY INSTRUCTIONS
1 - High pressure fuel circuit
IMPORTANT: Given the very high pressures in the high pressure fuel
circuit (1350 bars), comply with the following instructions.
Do not smoke near to the high pressure circuit during repairs.
Avoid working near to flames or sparks.
When the engine is running:
, do not work on the high pressure fuel circuit,
, always remain out of the range of a possible fuel jet which may cause
serious injury,
, never put your hand near to a leak on the high pressure fuel circuit.
After switching off the engine, wait for 30 seconds before starting work.
Note: It is necessary to wait for 30 seconds to allow the high pressure
fuel circuit to return to atmospheric pressure.
All operations on the fuel circuit are performed in the presence of fuel with
additive. It is recommended that gloves and protective goggles are worn
as the additive is a slight skin irritant.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
133
Chapter 14
2 - Fuel additive circuit
Do not smoke near to the fuel additive circuit during repairs. Avoid working near to flames or sparks.
The additive is a slight skin irritant; it is recommended that gloves and protective goggles are worn.
Protection of the environment: used additive and items used for cleaning the filter must be recycled.
The additive must be stored under the following conditions: , away from moisture,
, away from light,
, away from heat,
, in its original sealed, opaque packaging, to prevent the solvent from evaporating.
The contents of any opened containers must not be used and must be recycled.
3 - Operations on the particle filter
Forced regeneration leads to very high exhaust gas temperatures (450:C
at the exhaust pipe outlet):
, always keep well away from the exhaust pipe,
, use suitable exhaust gas extraction equipment,
, the working area must be clean and tidy,
, the vehicle chassis must be clean,
, the fuel tank must contain at least 20 litres of fuel to prevent the fuel from overheating,
, the coolant temperature must be above 65:C, before performing a
forced regeneration.
It is recommended that a mask and protective goggles are worn when removing and refitting the particle filter (risk of inhaling cerine).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
134
Chapter 14
4 - Working area
The working area must be clean and tidy.
Parts being repaired must be stored away from dust.
5 - Preliminary operations
IMPORTANT: The operator must wear clean overalls.
Before starting work on the injection circuit, the connectors of the following sensitive components may have to be cleaned (see corresponding operations):
, fuel filter,
, high pressure fuel pump,
, high pressure fuel common injection rail,
, high pressure fuel lines,
, diesel injector carriers.
IMPORTANT: After removal, blank the connectors of the sensitive
components immediately with plugs, to prevent the
ingress of dirt.
Use the correct tightening torques for the above components of the high
pressure fuel circuit, using a regularly inspected torque wrench: , diesel injectors,
, high pressure fuel sensor,
, high pressure fuel lines.
The DW12TED4 engine requires particular care to be taken when working on the fuel additive circuit.
Cleanliness of the fuel additive circuit:
, additive tank,
, additive injector supply and return pipes,
, additive injector.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
135
Chapter 14
III - MAINTENANCE
A - INJECTION SYSTEM
Bleed water from the fuel filter every 20 000 km.
Replace the fuel filter every 60 000 km.
Warning: The fuel filter is designed to be used on a sophisticated injection
system: refer to the procedure given in the mechanical folder of
the vehicle in question. It is recommended that gloves and
protective goggles are worn when handling fuel.
Note: It is recommended that the cleanliness of the "Swirl" control
electrovalve filter is checked periodically.
B - PARTICLE FILTRATION SYSTEM
Replace or clean the particle filter every 80 000 km.
Top up the additive tank every 80 000 km.
Note: Additive is sold by the Replacement Parts Department in 1 litre
containers (part number PR 9736.65).
IMPORTANT: Use the recommended additive. All other additives (or
products) used will lead to incorrect operation of the particle
filtration system.
Dealing with waste:
, additive and components used for cleaning the filter must be recycled,
, the contents of any container which has been opened and not used
immediately must be recycled.
C - DIAGNOSTIC TOOLS
Diagnostic tools are used to carry out servicing and diagnostic operations on
the particle filtration system:
, reading of fault codes,
, parameter measurements,
, forced regeneration,
, reinitialisation of the total additive quantity.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
136
Chapter 14
D - PARAMETER MEASUREMENTS
Particle filter state
This shows the status of the particle filter (regenerated, intermediate zone,
loaded, overloaded, clogged or punctured).
Particle filter differential pressure (difference between inlet/outlet pressure).
This parameter corresponds to the pressure difference between the inlet and
the outlet of the particle filter.
This value is similar to the "filter state" parameter.
The pressure differential varies depending on the vehicle mileage and driving
conditions.
Regeneration assistance state
This parameter states whether regeneration assistance is in progress (active
or not active).
Total amount of additive injected
The total amount of additive injected since the additive tank was last refilled.
Average distance of last 5 regenerations - distance travelled since
regeneration
Refer to the operating phases - particle filter section.
E - FORCED REGENERATION
Before a particle filter is cleaned, forced regeneration allows any remaining
soot to be removed and facilitates cleaning of cerine deposits. F - REINITIALISING THE TOTAL ADDITIVE QUANTITY
After replacing or cleaning a particle filter, the total amount of additive must
be reset in the additive ECU (calculation of the injection ECU cartographic
maps).
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
137
Chapter 14
IV - REPLACING PARTS: OPERATIONS TO BE PERFORMED
A - DIAGNOSTIC BEFORE REPAIR
Warning: Before working on the system, read the memories of all ECUs.
Refer to the fault finding charts:
, fault charts using fault codes,
fault charts using customer complaints (without fault codes). ,
B - REPLACING PARTS
Warning: Before adding or replacing parts, ensure that the customer has
their confidential card.
COMMENTS / COMPONENTS OPERATIONS TO BE REQUIRED REPLACED PERFORMED INFORMATION
Injection ECU Programming of the injection Access code
ECU
Checking of telecoded Description of the vehicle
parameters (if necessary, equipment
telecoding of the injection ECU)
Forced regeneration VIN
Fuel additive ECU Programming of the total additive Total additive quantity
quantity parameter parameter from the old
additive ECU
Particle filter Reinitialisation of the total
additive quantity (reset)
Treatment of the old particle filter
Additive tank Filling of the additive tank
Priming of the additive circuit
Treatment of the old additive
Additive Filling of the additive tank
Priming of the additive circuit
Treatment of the old additive
The following procedures require the use of the diagnostic tools:
, programming of the injection ECU,
, telecoding of the injection ECU,
, programming of the total additive quantity parameter.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
138
Chapter 14
C - PROGRAMMING THE INJECTION ECU
Warning: Swapping an injection ECU between two vehicles makes it
impossible to start the vehicles.
When fitting a new injection ECU, the engine immobiliser system has to be
programmed.
In order to program the engine immobiliser system, you must: , be in possession of the access code to the built-in systems interface
(written on the customer's confidential card),
, be in possession of a new injection ECU,
, use the diagnostic tool,
, carry out an engine ECU programming procedure: "PROGRAMMING THE
ENGINE ECU",
, download the injection ECU (if necessary).
D - TELECODING THE INJECTION ECU
This procedure is used to reduce diversity.
Parameters which can be telecoded:
, engine cooling (fan unit),
, air conditioning pressure sensor,
, gearbox,
, diesel injection type,
, additional heating,
, ECUs.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
139
Chapter 14
E - REPLACING THE INJECTORS
Original fit.
Diesel injector carriers marked as a function of their injection pipe diameter
(diesel flow) (class reference 1, 2 or 3).
The cartographic maps of the injection ECU include the class of injectors fitted
on the engine.
Repair.
If an injector is replaced, an injector of the same class must be fitted.
Warning: Fitting an injector of a different class leads to incorrect operation
of the particle filtration system.
Note: Fitting 4 injectors of a different class is possible, provided that their
new class is telecoded into the injection ECU.
F - DOWNLOADING THE INJECTION ECU
The software of the injection ECU is updated by downloading (ECU with a
flash EPROM).
Note: This operation is performed using the diagnostic tools. G - PROGRAMMING THE TOTAL ADDITIVE QUANTITY PARAMETER
If the additive ECU is replaced, the total additive quantity must be
programmed into the new additive ECU.
Warning: Swapping an additive ECU between two vehicles is forbidden. H - PRIMING THE ADDITIVE CIRCUIT
After opening the additive circuit, it must be reprimed: switch the ignition on
then off again 3 times.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
140
Chapter 14
V - WARRANTY RETURN PROCEDURE
A - COMPONENTS OF THE INJECTION SYSTEM
Before returning parts to the assessment centre, the following components
must be blanked, placed in a plastic bag and packaged in their original
packaging:
, diesel injectors,
, high pressure fuel pump,
, high pressure fuel common injection rail,
, high pressure fuel sensor,
, fuel filter.
B - INJECTION ECU
The injection ECU will automatically lock if it is disconnected.
IMPORTANT: When returning parts under warranty, return the injection ECU
with its access code.
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
141
Chapter 15
WIRING DIAGRAM I - LAYOUT DIAGRAM
SDI046P
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
142
Chapter 15
II - PARTS LIST
BB00 - Battery
BM34 - Engine relay unit with 34 fuses BSI1 - Built-in systems interface C001 - Diagnostic connector
CA00 - Ignition switch
MC11 -
MC30 -
MC34 - Earths
MC35 -
MM01 -
0004 - Control panel
1115 - Cylinder reference sensor 1150 - Pre-post heating unit 1160 - Preheater plugs
rd1208 - High pressure pump 3 piston deactivator 1211 - Fuel sender pump
1220 - Coolant temperature sensor 1221 - Diesel thermistor
1233 - Turbocharging pressure regulation electrovalve
1253 - All or nothing EGR electrovalve 1261 - Accelerator pedal position sensor 1263 - EGR + throttle electrovalve 1264 - Swirl electrovalve
1276 - Diesel heater
1285 - Inlet air heater electrovalve 1310 - Air flowmeter
1312 - Inlet air pressure sensor 1313 - Engine speed sensor
1320 - Engine management ECU 1321 - High pressure fuel sensor 1322 - High pressure fuel regulator 1331 - Injector - cylinder n? 1
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
143
Chapter 15
PARTS LIST (continued)
1332 - Injector - cylinder n? 2
1333 - Injector - cylinder n? 3
1334 - Injector - cylinder n? 4
1341 - Particle filter pressure differential sensor 1344 - Upstream exhaust gas temperature sensor 2100 - Stop switch
2101 - Redundant stop switch
7306 - Cruise control safety switch (clutch switch) 11 -- - Preheater ignition function
15 -- - Engine cooling function
70 -- - ABS function
72 -- - Trip computer, clock function
80 -- - Air conditioning, climate control function
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
144
Chapter 15
BOSCH HDI EDC 15C2 INJECTION SYSTEM AND PARTICLE FILTER
本文档为【E-Book - Injection Hdi Bosch Edc 15c2 Pour Moteur Dv4Td - 153 Pp - English】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑,
图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。