REDA公司UHT杀菌机设备参数

REDA公司UHT杀菌机设备参数 Alarm List Alarm 1:Emergency inseried Alarm 2:Product pump termic switch Alarm 3:Water pump termic switch Alarm 4:Anomalie inverter separator Alarm 5:Low level supply water Alarm 6:Separator low turns Alarm 7:Separator high turns Alarm 8:separator vibration alarm Separator:分离器 Working time setup Production working time 生产排渣间隔 10 min Production discharge time 生产排渣时间 25/100 s Partial discharges before long discharge 排渣前的部分排渣 nr. 5 s CIP working time CIP排渣间隔 3 min CIP discharge time CIP排渣时间 30/100 s Long discharge time 长排渣时间 40/100 s Time Rinse-closing Closing time setup Closing time(sec) 8 Starting closing time(sec) 30 Safety closing cycletime(min) 水顶时间间隔 5 Safety closing time(sec) 水顶持续时间 2 Rinsing time setup 冲洗时间设置 Pre-rinse time(sec) 预冲洗时间(排渣前) 5 Post-rinse time(sec) 后冲洗时间(排渣后) 5 Cooling cycle time(min) 水冷却(离心机)时间间隔 5 Cooling time(sec) 水冷却持续时间 5 Control page 控制页面 REDA PASSWORD ACTIVE SIGNALINGS 实时信号 HISTORICAL SIGNALINGS 历史信号 PID page PID UHT Parameters PREPARTION PARAMETERS 准备参数 PRODUCTION PARAMETERS 生产参数 NORMAL AND ASEPTIC CIP PARAMETERS 普通或无菌CIP参数 THRESHOLDS ALARMS PARAMETERS 报警阀值参数 Trend page CAPACITY UHT GRAPHIC TEMPERATUER UHT GRAPHIC TEMPERATUER UHT GRAPHIC Work page CYCLES MENU 循环目录 RECIPE SELECTS 方法选择(工艺选择) RECIPE WRITE 方法写入(工艺设定) SEGNALI REDA<->PSC PREPARTION PARAMETERS ) 设备杀菌温度 145.0 sp temp. sterilize.T1T with water(? sp capacity plant on steril.F1T(l/h) 5000 sp capacity plant wait prod F1T(l/h) 5000 sp holder pressure P1T(bar) 4.5 sp return pressure P5T(bar) 3.5 sp temp. return BT T5T STER(?) 85.0 PHASE 1:initial rinsing time(min) 最初冷冲洗时间 5 PHASE 2:heating time(min) 加热时间 5 PHASE 3:sterilization(min) 杀菌 30 PHASE 4:cooling time(min) 冷却时间 5 PHASE 5:stabilization time(min) 稳定时间 5 PHASE 6:attend production time(min) 等待生产时间 5 PRODUCTION PARAMETERS sp temp. sterilization product T1T(?) 140.0 sp capacity plant F1T(l/h) 5000 sp temp. filling T3T(?) 22.0 sp temp. return BT T5T PROD(?) 30.0 sp pressure holder P1T(bar) 4.5 sp pressure return P5T(bar) 1.5 PHASE 7:water drain from line 1(sec) 1线排水 10 PHASE 7:water drain from line 2(sec) 2线排水 10 PHASE 8:discharge water by V5(lt) 排水V5 600 PHASE 9:recovery water + product V4(lt) 茶水回收V4 120 PHASE 10:production product to tank(ql) 茶入罐 600 PHASE 11:recovery product L1(sec) 1线茶回收 15 PHASE 11:recovery product L2(sec) 2线茶回收 15 PHASE 12:discharge product to tank(lt) 茶排放入罐 650 PHASE 13:recovery product + water V312(lt) 茶水回收 200 PHASE 14:attend new prod.O cip 等待继续生产或CIP 60 NORMAL AND ASEPTIC CIP PARAMETERS cip 1=double 2=normal 3=lye 4=rinse 2 sp capacity discharge F1T(l/h) 8000 sp capacity recicle F1T(l/h) 8000 sp pressure return P5T(bar) 1.0 sp temp. rinse T1T(?) 80.0 sp temp. 1?lye T1T(?) 110.0 sp temp. 1?acid T1T(?) 65.0 sp temp. 2?lye T1T(?) 90.0 sp temp. 2?acid T1T(?) 55.0 concentration 1?lye(%) 2.5 concentration 1?acid(%) 1.0 concentration 2?lye(%) 1.5 acid(%) 0.5 concentration 2? PHASE 15:time 1?rinse warm cip(min) 第一次热冲洗 10 PHASE 16:time 1?lye cip(min) 第一次碱洗 30 rinse warm cip(min) 第二次热冲洗 15 PHASE 17:time 2? PHASE 18:time 1?acid cip(min) 第一次酸洗 30 PHASE 19:time 3?rinse warm cip(min) 第三次热冲洗 20 PHASE 20:time 2?lye cip(min) 第二次碱洗 20 PHASE 21:time 4?rinse warm cip(min) 第四次热水冲洗 10 PHASE 22:time 2?acid cip(min) 第二次酸洗 20 PHASE 23:time 5?rinse cip(min) 第五次冲洗 10 PHASE 24:time rinse final cip(min) 最终冷冲洗 5 Temper T10T 预热段出口 TVT 蒸汽加热温度 T1T 加热段出口 T1BT 保温段出口 T2T 预冷段出口 T3T 塔水冷却段出口 T4T 冰水冷却段出口 TCT 蒸汽屏障温度 T4AT 灌注出 T5T 回流入平衡桶温度 灌注机 Temperatures Filling head V314 96.0 Filling valve steam barrier 100.0 Steam spray cap V311 95.0 Steam spray valve V312 95.0 Product pipe CIP 70.0 Product pipe STZ 110.0 Product pipe Cooling 45.0 T2-Heating section outlet 灌注出口 STZ 120.0 T2-Heating section outlet 灌注出口 PRD 50.0 Drums Batch 200kg Delta-PreBatch 3.0kg Repetition no. for AVG error calculation 2 Maximum error allowed 2.0kg Start 1-Filling head lowering 35.0kg Timing 1-Filling head lowering 8 [0,1s] 55.0kg Start 2-Filling head lowering Timing 2-Filling head lowering 8 [0,1s] Start 3-Filling head lowering 85.0kg 8 [0,1s] Timing 3-Filling head lowering Start 4-Filling head lowering 110.0kg Timing 4-Filling head lowering 10 [0,1s] MF00 循环结束 MF01 喷帽打开 MF02 喷帽关闭 MF03 帽夹打开归位&再次下降 MF04 蒸汽喷帽-温度控制 MF05 帽夹关闭 MF06 帽夹打开归位&再次下降 MF07 帽夹没在中心 MF08 灌注阀下降 MF09 批量 MF10 灌注阀完全打开 MF11 灌注阀部分打开 MF12 灌注阀关闭 MF13 蒸汽喷阀 MF14 等待灌注阀上升 MF15 灌注阀上升 MF16 帽夹到中心 MF17 帽夹归位&再次下降 MF18 帽夹打开 MF19 喷帽打开&帽夹上升 MF20 喷帽关闭