sankyo_robotics_3000spwin_software_maintenace_manual
Maintenance Tool for the SC3000 Robot Systems
(For Maintenance Work Users)
AMO-NP-03017-34
SC3000 Robot Systems
3000SPWin Operation Manual
For Maintenance Work Users
This English version manual has been prepared according to the descriptions of the latest
issue of the corresponding Japanese version (7th issue dated March 1, 2005)
listed below:
dated March 1, 2005 ?? 7th issue
Notices for Safety
CAUTION
This notice advises of a condition that could present a potential hazard
where personal injury or damage of material are possible unless care is
exercised and correct operations are performed
? No part of this manual may be used or reproduced in any manner whatsoever
without the written permission of Sankyo Seiki Mfg. Co., Ltd.
All descriptions included in this manual are subject to change without notice. ? ? This publication may contain technical inaccuracies or typographical errors. Any
of your questions and comments on the contents of this document should be
directed to Sankyo Seiki Mfg. Co., Ltd.
Sankyo Seiki Mfg. Co., Ltd. is exempt from any responsibilities, for damages ? caused directly and/or indirectly by the contents of this manual.
March 2005 Edition
Sankyo Seiki Mfg. Co., Ltd.
Ina Plant
6100 Uenohara, Ina-shi
Nagano-Pref., Japan (Postal Code 396-8511)
TEL 0265 (78) 5111
FAX 0265 (78) 5116
Copyright ? 2002, Sankyo Seiki Mfg. Co., Ltd.
AMO-NP-03017-34
Contents
? Related Documents
? For Safety Work
1.
Generals.......................................................................................................................................1
2. Operation
Environment.................................................................................................................1
3. Installing and Uninstalling of
3000SPWin......................................................................................3
3.1
Installing...................................................................................................................................3
3.2
Uninstalling..............................................................................................................................4
4. Basic
Operations...........................................................................................................................5
4.1 Online
Operation......................................................................................................................5
4.2 Offline
Operation......................................................................................................................5
4.3 Main
Screen.............................................................................................................................6
4.4 Setup of
3000SPWin................................................................................................................8
4.5 User
levels...............................................................................................................................9
4.5.1 How to Control the User
Levels......................................................................................9
4.5.2 How to Change the User
level......................................................................................10
5. Various Maintenance
Functions..................................................................................................11
5.1 Controller status
monitor........................................................................................................11
5.1.1 Controller
error..............................................................................................................11
5.1.2 Task status
monitor.......................................................................................................12
5.1.3 DI/DO
monitor...............................................................................................................15
5.1.4 Robot current position
monitor......................................................................................16
5.1.5 Version
check...............................................................................................................17
5.2 Maintenance
work..................................................................................................................18
5.2.1 Change operation
range...............................................................................................18
5.2.2 Motor
replacement........................................................................................................19
5.2.3 Change home
position..................................................................................................23
5.3 Servo
monitoring....................................................................................................................24
5.3.1
Buffering.......................................................................................................................24
5.3.2 Monitor the thermal value and implementation
value....................................................27
5.4 ROM
communication.............................................................................................................29
5.4.1 Outline of ROM
communication....................................................................................29
5.4.2 Erase all in
flash...........................................................................................................29
5.4.3 Upload Controller System
Software..............................................................................29
5.4.4 Download System Software to
Flash............................................................................29
5.5 Axis
move..............................................................................................................................30
5.6 File
manager..........................................................................................................................31
5.7 HWDEF
editor........................................................................................................................33
AMO-NP-03017-34
Notices for Robot System Users
This manual has been prepared on the premise, for safety reasons, that the personnel
who read and use this manual have already acquired sufficient knowledge on operation of
automated equipment and devices.
Before any operation or maintenance work begins on the robot system(s), be sure to read and understand the section titled, “For Safety Work”, which soon appears in this manual.
AMO-NP-03017-34
Related Documents
For the robot system(s), there are various instruction manuals listed below and you are
requested to refer to those documents as you require.
Listed below are the documents related only to the SC3100 robot systems.
System Instructions Rev. 3
provides the comprehensive information on the SC3150/SC3400 Robot Systems.
Installation Manual Rev. 3
describes how to install the Controller, the way of cabling work, how to perform the
ABS homing, etc.
SC3150 Controller Hardware Manual
SC3400 Controller Hardware Manual
describes electrical specifications on the corresponding Controller.
Instructions on AD1309 Expansion I/O Card (Option)
Instructions on AD1319 Expansion I/O Card (Option)
Instructions on AD1339 HS Card (Option)
describes electrical specifications and other information on each expansion card.
Instructions on AD1316 Safety Connector (Option)
describes electrical specifications and other information on the AD1316 Safty
Connector.
Instructions on AD1340 Remote Switch Box
describes electrical specifications and other information on the AD1340 Remote
Switch Box.
Instructions on AB4301 CC-Link Card (Option)
describes electrical specifications and other information on the AB4301CC-Link
Card.
Buzz2 User’s Guide
describes the operation of Buzz2, which has been developed as “ADS” (*).
Pendant Operation Manual (Option) Rev. 3
describes the operation of the Pendant to be used, being connected to the
Controller.
3000SPWin Operation Manual (For General Users)
describes the operation of the maintenance work software, 3000SPWin, for the
SC3000 series robot systems.
3000SPWin Operation Manual (For Maintenance Work Users)
This manual.
SC3150 Controller Maintenance Manual
SC3400 Controller Maintenance Manual
describes the checks and parts replacement work, spare parts, etc. for the
corresponding Controller.
SSL/E Language Reference Manual Rev. 2
SSL/E means “Sankyo Structured Language / Enhanced”, a robot language to be
used for the SC3000 Series Robot Systems. Discussed in this manual are; how to
create programs in SSL/E, syntax of SSL/E and detailed information on
each
language command.
Manipulator Hardware Manual
describes the installation, maintenance and inspection work for the Manipulator.
Specifications depending on the Manipulator are given in this manual.
(*) “ADS” stands for the Application Development System and it is the name of the
software development environment, which is used to create Robot programs in SSL/E on a PC and download them to the Controller to enable testing of source program level.
AMO-NP-03017-34
For Safety Work
1. Introduction
Industrial robots usually have wide workspace and their manipulators move in high speed. Since they require special working procedures, such as teaching operation, any industrial robots is accompanied by some critical operating condition that other industrial systems
do not have. Furthermore, erroneous motion may potentially be caused in the robot
systems by wrong operation or electromagnetic noise effect. The Sankyo SC3000 Robot Systems are supplied with various safety operation
functions, and descriptions on safety
operations are included in the manuals and their related publications.
All the Sankyo Robot users are highly recommended to read the entire “For Safety
Operation” publication and the other related manuals to become familiar with safety
operations and instructions for the SC3000 Robot Systems.
1.1 General Notice
Ensure compliance with all local, state and national safety and electrical codes for the
installation and operation of the Sankyo Robot System. For example, if you used the
Sankyo robot in the USA, you need to be very familiar with the American National
Standards Institute / Robotic Industries Association (ANSI/RIA) safety standard
R15.06-1992. In other countries, the equivalent codes and/or standards shall be
observed.
1.2 Training Course
In the codes and standards regarding industrial robots, it is described that the operators
who perform teaching, inspection and tuning, and repair work for industrial robots are
obligated to receive special training for their work. All the operators for such work of the
Sankyo Robot Systems and their safety administrators need to receive instruction through
the special training course organized by Sankyo.
1.3 Scheme for Safety Operation Administration
For using the Sankyo Robot Systems, you shall designate the persons in charge of the
Robot operation and its safety operation respectively. Furthermore, organize the scheme for safety operation administration, such as emergent norm and reporting network, in
preparation for emergencies.
1.4 Working Norm
For safety operation administration, prepare the working norm and ensure to observe the norm.
i AMO-NP-03017-34
2. Precautions for Installation and Operations
2.1 Installing a Safety Barrier
Consider installing a safety barrier to avoid any person from stepping into the Manipulator
workspace.
? It must be possible to see the Manipulator movement through the barrier from its
outside.
? The barrier shall have enough rigidity with which the barrier would neither easily
get moved, broken nor damaged.
? The barrier shall have an entrance only through which the operator can enter the
barrier inside.
? A safety plug shall be placed at the entrance, which the operator pulls out before
entering the Manipulator workspace to disable the Manipulator from moving.
2.2 Installation Environment
If your installation site is relevant to any of the following items, consider improving the
installation environment or taking countermeasures required.
? The temperature at the installation site is out of the range of 0,
40?.
? The humidity at the installation site is out of the range of 30,90% RH,
or the
temperature changes so quickly that moisture condensing is caused.
? Some noise generator(s), (such as high-voltage equipment, electric driving
systems, etc.) is located near to the installation site.
? Oil mist and/or dust is generated at or around the installation site.
? Corrosive gas is generated at or around the installation site.
? The installation site is in explosive or inflammable atmosphere.
? Excessive vibration and/or mechanical shock is generated at or around the
installation site.
? The installation site is ill-ventilated because of bad ventilation condition.
2.3 Installation
When installing the robot system, pay attention to the following notes:
? In order to perform teaching operation and maintenance/inspection work safely,
provide the robot system and its peripheral equipment with sufficient working area
for the operator.
? The robot system and its peripheral equipment shall be so installed as that the
operator can always see them. Wire emergency stop button(s) from
more than 1 of
I/O-1, I/O-2 or AUX connector of the Controller to make operator(s) push the
emergency stop button easily and stop the Manipulator.
? The Pendant shall be so placed that the operator can use it outside the Manipulator
workspace while watching the Manipulator movement.
? Refer to the “Installation Manual” as well for the other notices
regarding installation
work.
ii AMO-NP-03017-34
2.5 Connecting Peripheral Equipment
CAUTION
- Before connecting any peripheral equipment, check the rated
voltage and current of the equipment. Connecting peripheral
equipment having its rated voltage and/or current outside the
specified allowable range may cause the Controller to get damaged.
- Do not keep the “/STBY” input always being turned on. Keeping it
always turned on, a realtime error occurs.
iii AMO-NP-03017-34
3. Preparation of Working Norm
Referring to the descriptions below and the manuals on the SC3000
Robot Systems,
make up your working norm and ensure to observe it. For the communication to the
observing personnel and the operator(s) of the other related equipment, prepare the
safety care sheets and perform communication according to the descriptions on them. On
such an occasion, oral communication may have some problem because of noisy working
locations and using body language may be recommended.
3.1 Checks Before Robot Operations
Before placing the SC3000 Series Robot System into operation, perform the following
checks. If you find any problem, repair the broken part or take actions required for the
problem. You are recommended to make your own checklist, referring to the following
descriptions:
? Check on the safety plug
Check that removing the safety plug of the safety barrier entrance surely
causes an emergency stop.
? Check on the cables
a. Make sure that the interface cables are free from any damage on their
outer cover.
b. Make sure that the EMS cable is free from any damage on its outer cover.
c. Check that there exists no damage such as a dent with the Controller,
Pendant and/or Manipulator outside section.
? Check on the Manipulator movement
After making sure of no person inside the Manipulator workspace, try to move
every axis by using the Pendant to check if the Manipulator moves smoothly
without any unusual noise.
? Check on the emergency stop button function
Check that pressing each of the emergency stop buttons (of the Pendant and
the external emergency stop button if any) surely stops operation.
? Making sure of no obstacle
Make sure that there exists no obstacle inside the Manipulator workspace.
iv AMO-NP-03017-34
3.2 Precautions for Teaching Operation
? Whenever possible, teaching operation shall be done while the operators being
outside the Manipulator workspace. If it is impossible to perform teaching
operation in that way, extreme attention shall be paid in preparation for
unpredictable erroneous motion and operation because the Manipulator moves at
high speed.
? All personnel for teaching operation including observing personnel shall have
received special instruction for their work, and only the personnel appointed by the
responsible chief person can perform teaching operation.
? Be sure to wear safety helmets, safety shoes and safety glasses.
? For teaching work, two men are required. One does teaching operation while the
other is observing the teaching at the control panel.
? The observing personnel is to do the following:
a. Devote himself to observing while standing at the position where all the
robot motion can be seen.
b. Press the emergency stop button immediately in an emergency.
c. Make no body other than the teaching personnel penetrate the work area.
? The personnel carrying out teaching operation shall always be ready to press the
emergency stop button.
? Before teaching work, perform pre-work checking with the check list which you
make according to item “3.1 Checks Before Robot Operations” of this
manual. In
case any unusual condition is found, take an appropriate action to solve the
problem.
? The Manipulator speed in teaching shall be 250 mm/sec or less.
? Place a "NOW TEACHING" sign plate onto the control panel.
? If you must enter the safety barrier inside section, pull out the safety plug at the
entrance of the barrier and carry it with you.
? For the communication to the observing personnel and the operator(s) of the other
related equipment, the descriptions of the safety care sheets shall be observed.
? Neither operate nor allow to operate any equipment, which may act as
a noise
generator, at the teaching operation area or its surrounding area.
? Do not use the Teaching Pendant by groping it while paying attention to only the
teaching points.
? Do not perform your work while turning your back to the Manipulator.
? Before teaching work, make sure that there is no obstacle near your feet. Be
careful to perform teaching work while standing on any high step (2 m or higher).
? When a failure comes up during your teaching operation, take actions as described
below:
a. Press the Emergency Stop button immediately when any erroneous
motion is observed.
b. Communicate with the observing personnel to turn off the main power
and place a "DO NOT TURN ON" sign plate at the main power switch.
c. When you check the failure after causing an emergency stop, first make
sure that the other related equipment is also stopping.
d. Pull out the safety plug at the entrance of the barrier and carry it
with
you during your work.
e. If the robot automatically stops due to power failure, ensure to stop the
robot, then check the problem cause to take actions required.
f. If any emergency stop device does not work, immediately turn off the
main power, then check the problem cause to take actions required.
g. Only the appointed personnel can do the work of problem solving.
v AMO-NP-03017-34
? To boot up the robot again after causing an emergency stop because of some
problem, first make the problem cause(s) clear and take the actions required. Then
carry out the re-booting operation according to the procedures described in item
“3.3 Operation Procedures“.
3.3 Operation Procedures
? Powering up
a. Turn on the main power
(a) Make sure that the switch you are now going to turn on is the main power
switch of the control panel.
(b) Make sure that nobody is in the Manipulator workspace.
(c) Make sure that no sign plate of "DO NOT TURN ON" is placed at the
main power switch.
(d) After making sure of the points described above, turn on the main power
switch of the control panel.
(e) At the time, check that the manipulator does not move at all.
b. Turn on the servo power
(a) According to what operation you want to do, turn the mode of the
Controller (*1) to the “Local” or “Teach”.
(b) Turn the Key Switch of the Pendant to the same position as the mode of
the Controller is turned to.
(c) Press the Manip. Power Switch (servo power switch = Green button) of
the Pendant.
(d) Make sure that the Servo power LED (Manip. Power) gets lighted.
(e) If the Manipulator shows any motion (even slightly) at this time, press the
Emergency Stop button to turn off the servo power.
(f) If any error happens in the procedures up to here, consult your
maintenance team to ask for taking actions.
Note *1: The mode of the Controller
The mode of the Controller means the mode setup of the Controller side.
It is different between the Controller models.
<In the case of the SC3150 & SC3400>
The mode setting input has prepared at the AUX connector in the rear
section of the Controller.
It is set by equipment that users wired or the mode change switch of the
Remote Switch Box, AD1340 (Option).
<In the case of the SC3100 & SC3300>
It is set by the mode change switch in front of the Controller.
<In the case of the SC3000 & SC3200>
The mode change switch of the Controller do not exist, therefore only the
mode change switch of the Pendant decide the operation mode.
vi AMO-NP-03017-34
? Initial operation check Perform initial operation check, usually at the beginning of the robot operation, to make sure that not only the robot system but also the other related equipment work properly.
a. Selecting the operation mode.
Turn the Key Switch of the Pendant and the mode of the Controller to the
“Local”.
b. Verifying the robot motion by the "Step" operation
(a) Press the “Step” key on the Pendant LCD screen.
(b) Make sure that there is neither unusual motion nor any teaching point
displacement.
c. Verifying the robot motion by continuous operation
(a) Press the "Start" key on the Pendant LCD screen to perform the
continuous operation from the top of the program. On this occasion, by
using the “Speed Override” function, first perform the continuous
operation at low speed, and then at the specified speed if there exists no
problem.
(b) Make sure that there is neither unusual motion nor any teaching point
displacement.
(c) In this operation, you shall always be ready to press the Emergency Stop
button.
? Teaching operation
a. Selecting the “Teach” mode
Turn the Key Switch of the Pendant and the mode of the Controller to the
“Teach”.
b. Using the Pendant, operate each axis to perform teaching and save the
teaching data. The following precautions shall be observed through the
teaching operation.
(a) Make sure that nobody is in the Manipulator workspace.
(b) Avoid any sudden motion of the Manipulator.
(c) Operate the Manipulator as slow as possible.
(d) Make sure that there is no obstacle near your feet.
(e) Do not deal with the Pendant roughly.
(f) Always be ready to press the Emergency Stop button.
(g) While holding the Pendant with your left hand, operate it with your
right
hand.
? Debugging
Debug the program created by using Buzz. On this occasion, with the “
本文档为【sankyo_robotics_3000spwin_software_maintenace_manual】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑,
图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
该文档来自用户分享,如有侵权行为请发邮件ishare@vip.sina.com联系网站客服,我们会及时删除。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。
本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。
网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。