给激光打印机添加碳粉（Add toner to the laser printer）

给激光打印机添加碳粉（Add toner to the laser printer） 给激光打印机添加碳粉(Add toner to the laser printer) How do I add powder to the Samsung ML-1610 laser printer?: 1, a black box attached to the cartridge, pushed with a spring lid over it 2, the original left all the toner thrown out. (no, unfortunately, different manufacturers of carbon powder, static electricity, diameter size may be different, mixed together will damage the drum) 3, make a funnel with clean white paper and add the carbon powder to about 1 bottles (100g). 4, installed on the OK. To remove the left cover of the drum, you can see the powder bin cover, clean up the waste powder, pouring Print-Rite's Samsung powder, about 40 yuan, filling well, can be filled 2--3 times, there is no counter of this drum At present, the most common printing equipment is inkjet printers, laser printers, needle printers three. From the printing speed and print effect, laser printers account for a lot of advantages. From the point of view of consumables, laser printers use toner much cheaper than ink cartridges used by inkjet printers. Generally speaking, a box of toner can print more than 2000 documents. However, for the average user, adding powder to the printer itself is a headache, and today I'm going to introduce the process of adding toner to the laser printer: First, the preparatory work: First of all, to the market to buy a bottle of laser printer dedicated toner, the price of special toner is generally 20 yuan to 40 yuan. To add powder to the laser printer, we also need to prepare some tools, including: screwdriver, oblique pliers (pliers), cotton, brush, leather tiger (or hair dryer) and so on. Two. Remove the toner cartridge: First remove the toner cartridge from the printer, find the fixed screw on the cartridge cover, and remove the screw (usually 2 pieces) of the cartridge cover with a screwdriver and close the screws. Use a "one" screwdriver to gently pry off the buckle on the cover, and then open the drum cover. Note: some toner is used as a wire buckle, then we use the diagonal pliers gently pull the bayonet on the wire to open the cartridge cover. When we see the cartridge is divided into two parts, and the drum core is connected with a spring pressing waste box, is part of the cartridge, add toner when we should be added to the new toner cartridge. Open the toner cover will waste toner remaining in the cartridge in the spill, in order to prevent pollution, we should have covered the table with a newspaper. Three. Clean the residual toner: A lot of toner when replacing does not actually run out of toner will be completely in the waste box or cartridge will often leave some toner, if not clean, we add the original toner and toner is possible because of the incompatibility and the formation of solid mass, so we add carbon powder before must first clean up the original toner. 1. clean up, first pour clean waste cartridges and toner cartridges in the toner, then use the brush gently to remove the residual toner in the toner box edge. Where the brush doesn't clean up, we can clean the used carbon powder with a leather tiger or an electric hair dryer. (hint: the waste toner using the hair dryer blowing and wiping toner at the bottom of the box, there will be a large number of carbon dust flying, to avoid contamination of other equipment, the operation should be as far as possible in the outdoor box) of the toner toner after cleaning, we will clean the toner cartridge around with a brush. 2. cleaning: clean up the charging roller cartridge and toner cartridge of waste waste, but also on the waste toner charging roller, magnetic roller for cleaning, cleaning method to clean up the charging roller as an example below: cleaning the charging roller, first find the fixed screw charging roller (usually in the head on both sides of the charging roller). Use a screwdriver to unscrew the screws. Take out the charging roller carefully from the toner cartridge. Generally, both ends of the charging roller are equipped with plastic gears. Before wiping, we should first remove the gears at the ends of the charging roller. (hint: the charging roller drum and drum core distance are very close to the surface of the core drum has a special coating, the coating will be destroyed once the printing effect affect the future. Therefore, when removing the two parts, do not use the screwdriver to contact the drum core, remove the charging roller and clean the waste powder on the charging roller with cotton or soft cloth. After cleaning, return the charging roller to the cartridge box and screw the screws at both ends. Then we can clean up the toner on the magnetic roller according to the method of cleaning the charging roller described above. Four, add a new toner: through the above cleaning, then we can add a new toner cartridge to the toner bottle when adding screw purchase, tear seal under the mouth, will slowly pour the toner cartridge toner cartridge, until the date add. When you put the toner into the toner cartridge, in order to avoid spreading the toner outside, we can press the paper pad at the mouth of the toner box to make it easier to add powder to the toner cartridge. Add toner, toner cartridges and toner waste will cover and tighten the screws. Then wipe the toner around the drum with a clean brush or soft cloth. Before placing the toner cartridge into the printer, we first shake the toner cartridge with the left and right of the hand so that the toner in the toner cartridge is evenly distributed so that it can be printed normally later. Five. After the above operation, we have to fill the toner cartridge toner. Then install the components back into the laser printer in the reverse disassembly procedure. 1. first detection cartridges is suitable for powder, rotating compact side gear, on the degree of visual powder magnetic roller is uniform, and if there is a scratch, magnetic roller powder or uneven scratches are not suitable for powder. At present, the scraper and magnetic roller in the regeneration industry demand is not very big, but I believe there will soon be an alternative spare parts are produced. 2, if the above problems do not have it, the second step is to clean up excess toner cartridge includes a magnetic roller on the toner, which is very important. Unscrew the screw under the roller. Take three thin slices in turn. (please pay attention to the positive and negative sides), then remove the magnetic roller, clean the sponge roller under the magnetic roller and the powder in the powder bin with a vacuum cleaner or a leather tiger. The above is the first step of adding powder. If you add the same brand again, you may omit step 2. The 3 and third steps are to load the carbon powder, open the powder bin, shake the toner and load it into the powder bin, cover the powder bin cover, place it flat, shake the powder bin, turn the magnetic roller to test the powder, and then install the machine test. Compatible difference of carbon powder and original carbon powder in printing effect: the resolution of image can satisfy the requirement of business card making and general color manuscript. The color depends on: the life of the magnetic roller and the life of the scraper and the quality of the carbon powder to decide. The magnetism of the magnetic roller decreases gradually, the printing color will gradually become shallow; the scraper is not good, will appear the powder leakage phenomenon, causes the printing quality to drop. So, when you buy compatible toner, you need to know something about the use of your printer. Powder filling and cleaning method for HP 5L/6L laser printer: First, open the machine to remove the toner cartridge, with oblique mouth clamp to one side of the metal pin pulled out outwards, on both sides of the silver metal pin can be pulled out after the toner cartridge is divided into two parts, with drum core is a waste powder collecting device, a magnetic roller is one piece for powder. The Two, clean up waste powder: the metal pin will collect waste powder in the light blue photosensitive drum on both sides of the dial, remove the photosensitive drum in dark, smooth, with the discharge roller, then two screw nails on the rotary scraper, scraper removed, slowly will waste bin waste powder poured out, then the scraper and the discharge roller, the photosensitive drum according to the original location of restoration (such as the need to replace the old drum core, scraper drum core, the scraper can be changed into new). The Three, filling toner: powder supply on one side of the magnetic roller without gear screw rotation, with plastic shell can be seen after a purple plastic lid, open the lid, the powder chamber and the magnetic roller toner completely clean (if not clean up the magnetic roller and the powder bin printing proofs possible bottom ash or writing light) magnetic roller will be installed, the application of force hold magnetic roller, magnetic roller to prevent out of place. The laser printer toner shake slowly into the powder supply chamber, cover the plastic cover, good plastic shell (attention: semi circular hole semi circle magnetic roller axis on the end of the plastic shell and the good), rotation of the magnetic roller side gently of the gear ring, the toner evenly. The Four. The powder supply and the waste powder collection parts are installed and disassembled according to the position of the opening, Plug in both sides of the metal pin. When the selenium drum is installed, the photosensitive drum baffle plate shall be pushed out, and the side gear of the light drum core shall be turned upwards, and the residue on the drum surface shall be removed, and the loader can be used.