AWWA_C219-2006(优化)

~, American Water Works Association The Authoritative Resource on Safe Water~ 6666 West Quincy Avenue Denver, CO 80235-3098 T 800 .926.7337 www.awwa.org ANSIj AWWA C219-06 (Revision of ANSIjAWWA C219-01) AW\VA Standard Bolted, Sleeve-Type Couplings for Plain-End Pipe .~. STANDARD c,7.",~.':o ,,, 51'nee 1881 AnOclatlon ....-.. --..-....----------­~IW..,' Amw.n HlI10MI S~lnstilutJl Effective date: February 1, 2007 First edition approved by AWWA Board of Directors Jan. 27, 1991. This edition approved Feb. 12, 2006. Approved by American National Standards Institute July 6, 2006. Advocacy Communications Conferences Education and Training ~ Science and Technology Sections Copynght American Water WorkS Association Provi ded by lHS under license witn AININA No reproduction or networ1<;ing permitted without license from lHS Not for Resale AWWA Standard This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe minimum requirements and do not contain all of the engineering and administrative information normally contained in speci ficati ons. The AWWA standards usually contain options that must be evaluated by the user of the standard. Until each optional feature is speCified by the user, the product or service is not fully defined. AWWA publication of a standard does not constitute endorsement of any product or product type, nor does AWWA test, certify, or approve any product. The use of AWWA standards is entirely voluntary. AWWA standards are intended to represent a consensus of the water supply industry that the product described will provide satisfactory service. When AWWA revises or withdraws this standard, an official notice of action will be placed on the first page of the classified advertising section of Journal AWWA. The action becomes effective on the first day of the month following the month of Journal AWWA publication of the official notice. American National Standard An American National Standard implies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether that person has approved the standard or not , from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review, and users are cautioned to obtain the latest editions. Producers of goods made in conformity with an American National Standard are encouraged to state on their own responsibility in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. CAUTION NOTICE: The American National Standards Institute (ANSI) approval date on the front cover of this standard indicates completion of the ANSI approval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of publication . Purchasers of American National Standards may receive current information on all standards by calling or writing the Ameri can Nat ional Standards Institute, 25 West 43rd Street, Fourth Roor, New York, NY 10036; (212) 642-4900. Science and Technology AWWA unites the entire water community by developi ng and distributing authoritative scientific and technological knowledge. Through its members, AWWA deve lops industry standards for products and processes that advance public health and safety. AWWA also provides quality improvement programs for water and wastewater utilities. All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information or retrieval system, except in the form of brief excerpts or quotations for review purposes, without the written permission of the publisher. Copyright © 2007 by American Water Works Association Printed in USA 11 Copyright American Water Works Association Provided by IHS under license with AI/WJA No reproduction or networking permitted without li cense from IHS Not for Resale Committee Personnel The Steel Water Pipe Manufacturers Technical Advisory Committee (SWPMTAC) Task group for updating C219, which developed this standard, had the following per­ sonnel at the time: Del H. Eaton, Chair R.N. Borland, Dresser Inc., Bradford, Pa. (AWWA) R.]' Card, Victaulic Depend-O-lok Inc. , Atlanta, Ga. (AWWA) K. Clark, Mueller Company, Decatur, Ill. (AWWA) R.R. Collins, JCM Industries Inc., Nash, Texas (AWWA) D.H. Eaton, Roman Industrials Inc., Bothell, Wash. (AWWA) Z.J. Gentile, Ford Meter Box Company, Pell City, Ala. (AWWA) B. Kane, Cascade Waterworks Manufacturing Company, Yorkville, Ill. (AWWA) M. Mintz, M-Square Associates Inc., Elmont, N.Y. (AWWA) R.N. Satyarthi, Baker Coupling Company Inc., Los Angeles, Calif (AWWA) K.L. Shaddix, Smith-Blair Inc., Texarkana, Texas (AWWA) M.J. Topps, Viking Johnson Ltd., Hitchin, Herts, UK (AWWA) D.R. Wagner, Consultant, St. Louis, Mo. (AWWA) The AWWA Standards Committee on Steel Pipe, which reviewed and approved this standard, had the following personnel at the time of approval: John H . Bambei Jr., Chair George]. Tupac, Vice-Chair Dennis A. Dechant, Secretary General Interest Members WR. Brunzell, Brunzell Associates Ltd., Skokie, Ill. (AWWA) R.L. Coffey, H DR Engineering Inc., Omaha, Neb. (AWWA) H.E. Dunham, MWH Americas Inc., Bellevue, Wash. (AWWA) S.N. Foellmi, Black & Veatch Corporation, Irvine, Calif (AWWA) 111 Copyright American Water Wor1