人力资源丹佛斯vlt5000资料

人力资源丹佛斯vlt5000资料 Danfoss 参数 表 关于同志近三年现实表现材料材料类招标技术评分表图表与交易pdf视力表打印pdf用图表说话 pdf 5000 1. 恢复工厂设定: - 按 ”MENU” - 找到参数 620 - 按 ”CHANGE DATA”, 选择 INITIALIZE - 按 ‘OK’ - 断开电源，等待电源灯熄灭 - 送电 2. Program parameters in ‘Menu’: Verify each change with ”OK” 102 , 马达功率 kW (见马达铭牌) 103 , 马达电压 V (见马达铭牌) 104 , 马达频率 Hz (见马达铭牌) 105 , 马达电流 A (见马达铭牌) 106 , 马达转速 rpm (见马达铭牌) 128 , 电机热保护。ETR TRIP 1 201 , 最小马达频率 Hz (见马达铭牌 – 60%)。杀菌机设为0 202 , 最高马达频率 in Hz。输出频率上限。 (见马达 铭牌 + 10%至少) 205 , 最高马达频率参考值。与参数202一样, 207, 208 , 加减速时间。5.00 sec. 315 , 4.0 mA 323 , 继电器输出。VLT 运转 - 按 ”DISPLAY STATUS” 当地 启动/停止 用于检查马达转向 1. 按 ”MENU” 2. 按 STOP/RESET (显示开始闪烁) 3. 将002更改为 LOCAL 4. 按START启动马达, 按STOP/RESET停机 5. 将002更改为REMOTE 6. 按START 显示回复为平光) 自动调谐 条件:参数设定已完成，转向正确 1. Press STOP/RESET (display start flashing) 2. Program parameter 002 = LOCAL 107 = ENABLE (RS,XS) 3. Start auto tuning by pressing START button Auto tuning takes approxiamately 3 - 4 min. 4. When auto tuning is ready, the alarm lamp start flashing on frequency converter and the display show: AUTO MOTOR ADAPT OK 5. Press STOP/RESET to reset alarm. 6. Restore parameter 002 = REMOTE 7. Press START (display return to steady light) 参数设定 Operation & Display Load & Motor References & Limits 001 ENGLISH 100 SPEED OPEN LOOP 200 132 Hz CLOCKWISE 002 REMOTE 101 H-CONSTANT TORQUE 201 Min 马达频率 003 000.000 102 202 马达功率 in kW Max 马达频率 004 SETUP 1 103 203 MIN - MAX 马达电压 in V 005 ACTIVE SETUP 104 204 0.000 马达频率 in Hz 006 NO COPY 105 205 Max motor reference 马达电流 in A 007 UPLOAD ALL PARAM 106 Rated motor speed in 206 LINEAR RPM 008 1 107 ENABLE (RS,XS) 207 5.00 s 009 FREQUENCY [Hz] 108 depends on the unit 208 5.00 s 010 REFERENCE [%] 109 depends on the unit 209 depends on the unit 011 110 100% 210 depends on the unit 马达电流 [A] 012 POWER [kW] 111 1.0 Hz 211 depends on the unit 013 LCP+DIG CTRL/ AS 112 not used 212 depends on the unit P100 014 DISABLE 113 100% 213 10.0 Hz 015 DISABLE 114 100% 214 SUM 016 DISABLE 115 100% 215 0.00% 017 ENABLE 116 0.50 s 216 0.00% 018 LOCKED 117 100% 217 0.00% 019 LOCAL=STOP 118 5 ms 218 0.00% 119 0.0 sec. 219 0.00% 120 0.0 sec. 220 not used 121 COAST/DELAY TIME 221 160% 122 COAST 222 160% 123 0.0 Hz 223 0.0 A 124 50% 224 IVLT,MAX 125 50% 225 0.0 Hz 126 10.0 sec. 226 132.0 Hz 127 0.0 Hz (OFF) 227 -4000.000 128 ETR TRIP 1 228 4000.000 129 NO 229 0 (OFF)% 130 0.0 Hz 230 0.0 Hz 131 0.0 Volt 231 0.0 Hz 232 0.0 Hz 233 0.0 Hz (Cont’d) Inputs & Outputs Special functions Serial communication 300 RESET 400 OFF 500 1 301 FREEZE REFERENCE 401 depends on the unit 501 9600 BAUD 302 START 402 depends on the unit 502 LOGIC OR 303 REVERSING 403 ON 503 LOGIC OR 304 COAST INVERSE 404 OFF 504 LOGIC OR 305 JOGGING 405 MANUAL RESET 505 LOGIC OR 306 SETUP MSB/SPEED UP 406 5 sec. 506 LOGIC OR SETUP LSB/SPEED DOWN 307 407 NO FUNCTION 507 LOGIC OR 308 REFERENCE 408 DISABLE 508 LOGIC OR 309 0.0 Volt 409 OFF 509 10.0 Hz 310 10.0 Volt 410 depends on the unit 510 10.0 Hz 311 NO OPERATION 411 depends on the unit 511 not used 312 0.0 Volt 412 DISABLE 512 DANFOSS 313 10.0 Volt 413 ON 513 1 sec. 314 REFERENCE 414 0.000 514 OFF 315 4.0 mA 415 1500.000 316 20.0 mA 416 % 317 10 sec. 417 0.015 318 OFF 418 8 ms 319 0-IMAX = 0-20 mA 419 30 ms 320 5000 Hz 420 5.0 321 0-FMAX = 0-20 mA 421 10 ms 322 5000 Hz 422 20.0 Volt 323 VLT RUNNING 423 parameter 103 324 0.00 sec. 424 parameter 104 325 0.00 sec. 425 parameter 103 326 UNIT READY/REM CTRL 426 parameter 104 327 5000 Hz 427 parameter 103 328 25000 Hz 428 parameter 104 329 1024 429 parameter 103 430 parameter 104 431 parameter 103 432 parameter 104 433 100% 434 0.02 sec. 435 not used 436 not used 437 NORMAL 438 ENABLE 439 parameter 201 440 0.01 441 9999.99 sec. (OFF) 442 0.00 sec. (OFF) 443 5.0 444 0.01 445 DISABLE 446 AUTOMATIC 447 0% 448 1.000 449 0.00% Technical functions 618 DO NOT RESET 619 DO NOT RESET 620 NORMAL OPERATION Note: , Parameter settings in bold italic are specific for TA FlexD. All other parameter settings are the factory settings from the manufacturer of the frequency converter (Software version: 3.0x). , For the setting of parameter 102, 103, 104, 105 and 106, 见马达铭牌. , Record all parameters changed from factory settings settings in test protocol. , Sett following parameters after ready test / commissioning: Parameter 7 to UPLOAD (save settings in display EEPROM) Parameter 14 to DISABLE (disable STOP-button on frequency converter display) Parameter 18 to LOCKED (disable parameter changes from display) , Save parameter settings to PC by VLT Dialog software program after test / commissioning.