拔动开关规格书技巧参数ss-12d00[宝典]

拔动开关规格书技巧参数ss-12d00[宝典] 规 格 书 SPECIFICATION DESIGNATION 系列:拨动开关 MODULE NO 型号:SS-12D00 0CIRCUIT 回路: 1P2T TIMING 切换类型: SHORTING 1( STANDARD TEST CONDTTIONS SHALL BE 5 TO 35? IN TEMPERATURE AND 45 TO 85% IN HUMIDITY。 温度5-35?,湿度45-85%标准状态下测试. 2( OPERATING TEMPERE RANGE—10 TO 60?。 温度-10~60?环境内使用. ITEM 项目 TEST CONDISTION测试条件 PERFORMANCE规格 6.ELECTRONICAL PERFORMANCE 电气性能 30mΩ max. CONTACT Being measured at 1kHz small current 6.1 RESISTANCE Contact resistance meter. 接触阻抗 在1kHz小电流下测量. 30毫欧 以下. Measurements shall be made following 100MΩ max. INSULATION Application of Dc 500V potential 6.2 RESISTANCE Across terminals and across terminals 绝缘阻抗 100兆欧 以上. And frame for 1 minute. 在端子之间和端子与壳之间加DC 500V 条件下,持续1分钟测量. AC 500V (50Hz or 60Hz) shall be WITHSTAND Applied across terminals and across terminals There shall be no breakdown. 6.3 VOLTAGE And frame for 1 minute. 耐电压 在端子之间和端子与壳之间加AC 500V 无击穿现象出现. (50Hz或60Hz) 条件下,持续1分钟测量. 7.MECHANICAL PERFORMANCE 机械性能 OPERATING Measure at the point 3mm from the tip 350gf?100gf 7.1 FORCE Of the actuator (knob). 动作力 在距离推杆前端3mm作测定点. A static force of 500gf being applied There shall be no sign of TERMINAL In one direction on the tip or the damage mechanically and 7.2 STRENGTH Terminal for 1 minute. electrically. 端子强度 一个500克之静电负荷施加于端子顶部的一个方无任何迹象显示机械及电器 向持续1分钟. 性能之损坏. ACTUATOR A static load of 1kgf being applied The deformation shall not be 7.3 STRENGTH In one direction of actuator for one min extreme and the actuator shall 推杆强度 一个1公斤静负荷施加于推杆之一个方向持续 mechanically work normally. 1分钟. 推杆无变形,可以正常操作. ITEM 项目 TEST CONDISTION 测试条件 PEREORMALNCE 规格 8.DURABILITY 耐久性 The tip of the terminals shall be A new uniform coating of solder Shall SLLDERING dipped 2mm in the solder bath at a cover a minimum of 75% of the surface Temperature of 230?5? for 3?0.5sec. 8.1 TEST being immersed. 可焊性试验 端子顶部被浸入焊锡池2mm深,温度230?5? 浸入的部分75%以上表面将被锡覆盖。 时间3?0.5秒. Solder bath method Solder temperature 230?5? Immersion time 3?0.5scc Without deformation of case Immersion depth up to the surface of Or excessive looseness of the board mechanically electrical characteristics Thickness of PCB 1.6 mm. Shall be satisfied. 焊炉焊的温度控制在230?5?，过炉焊接的时间本体无变形，能满足于机械、电器性能。 RESISTANCE 3?0.5秒，于(蒸板)厚度为1.6 mm. TO 8.2 SOLDERING Solder bath method Bit temperature 300?10? HEAT TEST 耐焊性试验 application time 3?0.5scc however excessive pressure shall not be applied to the terminal. 手焊接的时候温度需控制在300?10?，时间为 3?0.5秒，但不能在排脚上施加异常压力。 (1)Contact resistance接触阻抗. 100mΩ max.100毫欧以下. (2)Operating force动作力. ?30%Inltial 10000cycles of operation at a rate LIFI TEST of 15-18 cycles per minute with unloading. value. 寿命试验 无负载条件下,每分钟15-18次的速度操作10000变化范围初始值?30%. 8.3 次. (3)ITEN 项目—6.2 (4)ITEN 项目—6.3 (5)ITEN 项目—7.2 (6)ITEN 项目—7.3 80?2? for 96 hours , caner test keep HEAT TEST in normal condition for 30minutes. 耐热试验 在80?2?环境中放96小时,再放在正常环境中 (1)Contact resistance 150mΩ max. 8.4 30分钟后进行测试. 接触电阻150毫欧以下. 40?2? 90-95%RH for 96firs after test (2)Insulation resistance HUMIDITY 绝缘电阻. keep in mortal condition for 30 min. TEST 50MΩmin 50兆欧以上. 耐湿试验 在40?2? 90-95%RH环境中放96小时,再放在正8.5 常环境中,30分钟后进行测试. (3)There shall be no sign of damage At -20?3? for 96hours,after test mechanically and electrically. 无任何迹象显示机械及电器性能之损kept in normal condition for 30 min. COLD TEST 坏. 耐冷试验 在-20?3? 环境中放96小时,再置于正常环境8.6 中,30分钟后进行测试.